Low Profile Boundary
M60
M60
OVERVIEW
The M60 is a miniaturized condenser microphone with fully integrated electronics
and immunity from RF interference typically caused by cell phones and GSM devices.
Primary applications for the M60 are: podium, corporate board rooms, meetings and
video conferencing where aesthetics and audio quality are of prime importance. The
microphone element is cardioid by design; however a “hemi-cardioid” polar pattern is
produced when coupled with a flat surface such as a table, floor, wall or podium.
The striking design of the M60 brass housing is achieved through an intricate process
utilizing a computer controlled machining center. The bottom of the housing is
treated with a shock absorbent material for dampening purposes and has two
threaded holes that allow the M60 to be bolted into a permanent position if desired.
Microphone
FEATURES
· Optimized for voice
A high quality 12’ shielded mic cable is attached directly to the internal circuitry of the
M60 with the ability to exit the housing at either 180 or 90 degrees, depending on
whether the cable will be routed through a drilled surface. In addition, there are two
types of connectors offered: XLRm or terminal connectors.
MODEL VARIATIONS
Each microphone comes with a 12’ integrated cable terminating into a XLRm
(CONN170M or terminal connector (CONN170f)
M60 - Black with XLRm connector
M60P - Same as above with terminal connector
M60N - Satin nickel withXLRm connector
M60NP - Same as above with terminal connector
· Immunity from RF interference
· Extremely high sensitivity
· Miniaturized integrated preamp circuitry
· Proprietary low noise circuitry
· Designed, machined, assembled & tested in
the USA
· 3 year warranty
APPLICATIONS
· Video Conferencing
· Board rooms
· Podium
· Courtroom
SPECIFICATIONS
Transducer Type
Frequency Response
Polar Pattern
Output Impedance
Sensitivity
Equivalent Noise Level
Signal to Noise Ratio
Maximum SPL
Dynamic Range 108 dB
Power Requirements 18-52 V phantom
Connector 3-pin XLRm
Polarity Positive pressure on diaphragm
Materials / Finish
Weight
Length
Condenser
70 Hz - 8 kHz
Hemi Cardioid
150 ohms
68 mV / Pa @ 1k
22 dB (A-weighted)
72 dB
≥130 dB
produces positive voltage on pin
2 relative to pin 3 of output XLR
connector
Brass/ Black, Nickel Finish
232 g / 8.3 oz
63 mm / 2.48 in
FREQUENCY RESPONSE
ARCHITECT AND ENGINEER SPECIFICATIONS
The microphone shall be of the condenser type with modular capsule available
in hemi-cardioid polar pattern. The microphone shall be protected from RF
interference. The microphone shall have a fully integrated preamp circuitry
thereby eliminating the need for a remote phantom power module. The
microphone shall operate on 18-52 Volts DC and the nominal output impedance
shall be equal to 150 ohms at 1 kHz. The microphone shall have a sensitivity of
68 mV / Pa at 1 kHz. The microphone shall have a maximum SPL level of ≥130
dB with THD of 0.5%. The microphone shall be machined out of brass and
the dimensions shall be 63 mm in diameter by 12mm maximum height. The
microphone shall be the Audix M60
OPERATION AND MAINTENANCE
The M60 is a low impedance microphone and should be plugged into a “mic
level” input on your console, mixer or recording device. The M60 requires
phantom power and will NOT operate without phantom power voltage (18-52
Volts) which is available on most professional mic preamps and mixing devices.
If phantom power is not available on your equipment, use an external phantom
power source such as the Audix APS2. Avoid plugging or unplugging the
microphone into or out of the audio system unless the channel is muted or the
volume of the system turned down. Failure to do so may result in a loud popping
noise which could seriously damage the speakers and the sound system.
M60
POLAR PATTERNS
0
0
-3
30
-6
-9
60
90
120
2.0000K 4.0000K 8.0000K 12.0000K
-12
-15
-18
-21
-24
-27
-30
dBR
150
180
125.0000 250.0000 500.0000 1.0000K
Further miking techniques may be found at www.audixusa.com.
DIMENSIONS (mm)
63.00 mm
25.40 mm
Mounting holes
PRODUCT REGISTRATION: Please register your product online at www.audixusa.com/docs_12/about/product_registration.shtml.
SERVICE AND WARRANTY:
workmanship, Audix will repair or replace said product at no charge with proof of purchase. Audix does not pay or reimburse shipping costs for warranty repairs or returns. The warranty excludes
any causes other than manufacturing defects, such as normal wear, abuse, environmental damage, shipping damage or failure to use or maintain the product per the supplied instructions. No
Implied Warranties: All implied warranties, including but not limited to implied warranties of merchantability and fitness for a particular purpose are hereby excluded. The liability of Audix, if any,
for damages relating to allegedly defective products shall be limited to the actual price paid by Dealer for such products and shall in no event include incidental or consequential damages of
any kind. Should your microphone fail in any way, please contact the Audix Service department at 503.682.6933. A Return Authorization is required before returning any product. OTHER THAN
THIS WARRANTY, AUDIX MAKES NO WARRANTIES, EXPRESS OR IMPLIED, WITH RESPECT TO THE PRODUCTS, THE USE OF THE PRODUCTS, THE PERFORMANCE OF THE PRODUCTS. AUDIX SHALL
NOT BE LIABLE FOR SPECIAL INCIDENTAL, CONSEQUENTIAL, INDIRECT OR SIMILAR DAMAGES ARISING FROM OR BASED ON THE SALE, USE, STORAGE OR DISPOSAL OF THE PRODUCTS, AUDIX’S
SERVICE WORK, BREACH OF WARRANTY, BREACH OF CONTRACT. NEGLIGENCE, OR ANY OTHER THEORY OF LIABILITY, EVEN IF AUDIX HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
ALL SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE.
This microphone is under warranty for a period of 3 years to be free of defects in material and workmanship. In the event of a product failure due to materials or
www.audixusa.com
Audix Corporation 9400 SW Barber St. Wilsonville, OR 97070
503.682.6933 Fax: 503.682.7114
ver 3.1 03-18
Loading...