Audiovox XSN1V1 Quick Start Guide

What’s in the Box?

Base

Antenna

Flexible

Power Adapter or Cigarette Lighter

Socket

Rock Underground

1 Mount the Magnetic Mount Antenna 2 Route the Antenna Cable 3 Find a Location for Snap and Mount It

4 Initiate the Courtesy Period

5 Connect the Audio

CAUTION: Do not attempt to install, activate, or adjust any of the setting options described in this Quick Start Guide unless your vehicle is parked in a safe location.

1 2 3 4 5

Snap Radio

Magnetic Mount

Antenna

Aux In Cable

Cable

Routing Adapter

Alcohol Prep Pad

Antenna Alcohol Preparation Pad

A. Mount the Magnetic Mount Antenna outside your vehicle, on a clean and dry

horizontal surface that will always face the sky.

B. The best location is on the roof above the front windshield, centered between

the left and right sides.

Sedans and Coupes

Pickups and SUVs Convertibles*

* If the antenna can not

be placed above the windshield, place it on vehicle hood.

C. Install the Cable Routing Adapter to direct the antenna cable downward, if mounting on an

edge.

TIP: Use the Alcohol Prep Pad to clean the surface.

A. Tuck the antenna cable under the windshield rubber

molding and run it to the nearest corner.

B. Route the cable out of the molding and into the rubber

weather stripping around the door opening.

C. Lift the weather stripping. Tuck and run the cable

inside it to the bottom of the door opening. Replace the weather stripping.

D. Pull the cable out and route it toward the power adapter

or cigarette lighter socket location.

E. Plug the Magnetic Mount Antenna connector into the

ANTENNA connector on the Base of Snap.

TIP: Include enough slack in your routing to accommodate open doors or the hood lid. Coil any excess cable in a hidden location and keep it away from any vehicle pedals or controls.

Stalk

Plug

ANTENNA

AUDIO FM

Place Antenna Closer to A-Pillar if Cable Doesn’t Reach Center of Roof

Power Adapter or

Cigarette Lighter

Socket Location

Antenna Connector

A. Mount Snap by plugging the Base into the power adapter or cigarette lighter socket.

B. Grasp the rear of Snap’s Base and gently push in, while at the same time rotating the Base

slightly to the right and then to the left. Do not push it in by holding the Radio Control Unit or Flexible Stalk.

TIP: Choose a socket that doesn’t interfere with the driver’s vision or access to driving controls, won’t interfere with the deployment of airbags or other safety equipment, and makes Snap easily accessible for operation.

A. Power on your Snap by pressing the Power button. Ensure the

vehicle is outside and the antenna has a clear view of the sky.

B. When prompted, press the number button 1, then 2, then 3. The

Courtesy Period Begun message will verify that the Courtesy Period

has begun.

C. You will be notified about the length of the Courtesy Period and

prompted to set up the audio connection. Snap will then tune to channel 1.

TIP: At this point, you should have access to all the channels in a few minutes. However, leave Snap tuned to channel 1 until you have set up the audio connection.

NOTE: If Acquiring Signal or Chk Antenna Connection is displayed, verify that you have mounted and connected the antenna. Refer to “Mount the Magnetic Mount Antenna” on page 14, or to “Troubleshooting” on page 42 of the User Guide for additional help.

Press 1,2,3 To Begin

Courtesy Period Begun

Decide on one of the following in-box audio connection options. Refer to “Connect the Audio” on page 23 of the User Guide for details including other connection options.

Option 1: Best: Use the provided Aux In Cable, if your vehicle’s stereo system has an auxiliary input jack.

A. Plug one end of the cable into the AUDIO connector on Snap and the other end into the auxiliary

input jack on the vehicle’s stereo system.

B. Turn on your vehicle’s stereo system and set it to play from the auxiliary input source.

C. You should now hear the XM channel 1. The installation is complete.

TIP! Refer to your vehicle’s owner’s manual to find the location of the auxiliary input jack, or consult the vehicle dealer.

Audio Connector

AUDIO FM

Aux In

Aux In Cable

continued on other side...

Connect the Audio (continued) Snap Button Functions Snap Main Display

Option 2: Good: Use the PowerConnect™ feature of Snap. PowerConnect plays the XM audio through your vehicle’s FM radio.

A. Find and make a list of all available FM channels in your area that are

not being used by an FM radio station.

B. Pick the first FM channel on your list. Tune your vehicle’s FM radio to

this FM channel.

C. Set your Snap to transmit on the same FM channel that you have

selected on your vehicle’s FM radio:

i. Press FM on the top of Snap.

FM 90.1

ii. Turn the Rotary knob to select the available FM channel you

have chosen.

D. You should hear XM channel 1 through your vehicle’s FM radio. If you are satisfied with the

sound quality, the installation is complete.

E. If you are not satisfied, move to the next FM channel on your list and repeat the process.

Continue until you have found an FM channel with which you are satisfied.

F. Press FM or wait 10 seconds to exit the FM mode.

TIP: Refer to “PowerConnect Installation Instructions” on page 25 of the User Guide for details on how to find an available FM channel.

90.1

1 2 3 4 5

6 Explore, Enjoy and Subscribe

Once installation is complete, you can tune to other channels and listen to all the commercial-free music, plus live sports and the latest news, talk & entertainment on XM.

A. Turn the Rotary knob to tune to other channels and press the Previous or Next Category button

to browse and select the different categories.

B. Subscribe before the Courtesy Period expires. Follow the instructions displayed on the screen.

Call / Visit 866-408-9796

C. You can also subscribe anytime you want online or by phone. Just go to www.xmradio.com and

click on Activate Radio or call 1-800-XM-RADIO (1-800-967-2346).

TIP: To subscribe, you will need your Radio ID, which you can find by pressing MENU, on a label on the bottom of the gift box, on the label on the back of your Snap, and by tuning to channel 0.

To Subscribe xmradio.com

Number Buttons

Press to tune to a stored favorite channel, press and hold to store a favorite channel; in FM mode, press to select a stored FM preset, press and hold to store an FM preset.

Rotary Knob

Turn to tune to the previous or next channel within the current category; in FM mode, turn to tune FM channels.

Scan Button

Press to start or stop scanning through channels within the current category.

Front View (Radio Control Unit)

1 2 3 4 5

Previous/Next Category Buttons

Press to access the previous or next category; press and hold to cycle through the categories.

Top View (Radio Control Unit)

Power Button

Press to turn Radio on and off.

Menu Button

Press to access Radio ID and adjust audio level.

FM Button

Press to change to FM mode for configuring FM channels.

When listening to a channel, information about the channel and what is currently playing is displayed. The screen will alternate between displaying the artist name and song/program title; and displaying the category, channel name and channel number.

Antenna Signal Strength

Artist Name

or Talk Show Host

or Sports Teams/Score

Displayed when a

Favorite Channel or

FM Preset is selected