Audiovox XR9000 User Manual

Model XR9000

Owner’s Manual

Long Range Remote Start Security System

With Plug-In Shock Sensor & Starter Disable

IMPORTANT ! In order to provide you with the highest level of security to your
vehicle, this system is equipped with selectable manual override circuitry. It is
possible that you will need to override you security system if the transmitter
becomes lost, or inoperative due to battery failure. Reading the sections on
"Manually Overriding Your System" is necessary to fully underst and the procedure
required to enable your vehicle in such situations. In addition, the chart on the last
page of this manual has a section for the particular features and options installed
in your vehicle as well as the override method selected. Although the default
mode is "Valet Switch" operation, the system can be configured for "Custom
Code" operation for enhanced security. Confirm the override mode selected on
the last page of this manual, and familiarize yourself with the section on it's opera­tion.

FEATURES :

 1 Two Way 6 Button LCD Remote Control & 1 One Way 5 Button Remote

Control

 Seven Channel Code Learning Programmable Receiver
 External Superheterodyne Transceiver Antenna
 Single Or Two User Programmable W/Separate Control Outputs
 Single Button Lock/Unlock or Separate Button Lock/Unlock or Both
 Remote Keyless Entry With Optional Access Guard (must have power door

locks)

 Selectable Manual Override Mode
 New Enhanced Panic Feature (Any button other than unlock stops siren, no

change to the units state)

 Smart Disarm (If triggered, elect to shut off siren, or disarm entire unit )
 Adjustable Shock Sensor Via The Transmitter (Pre-Detect Off, Pre & Full Detect

Off, City Mode)

 Safe Start Output Controlled From Channel 3 (Option Channel 3 For T runk, Or

For R/S)

 24 Hour Time Start Mode
 Cold Temperature Start Mode
 2 or 4 Hour Automatic Start Mode
 Parking Meter Count Down Timer On LCD Remote
 Additional Count Down Timer Mode
 Remote Panic In All Modes (Press & Hold Lock /Unlock Button For 3 Seconds

To Engage)

 Improved Custom Code Override, User Selectable and Programmable
 Protected PBLED, (Push Button LED V alet/Program/Manual Override Switch )
 7-Function LED-Arm / Disarm / Zone 1 / Zone 2 / Zone 3 / Valet / Arming
 Intrusion Alert With Memory
 Instant Siren Activation
 Starter Disable Output

Page 1

128-7863

1 of 20

 Additional Engine Immobilizer Output, (Optional Relay Required)
 True Last Door Arming (Hardwire Only)
 Defective Zone By-Pass
 Defective Zone Chirp Confirmation (Unit Chirps To Report Zone Cleared)
 6 Tone Mini Siren
 Car Horn Output For Additional Alarm Response (Improved Timing To Minimize

RF Interference.)

 Additional Negative Trigger Input (Hood and Trunk)
 RF Inhibit With Ignition On
 Parking Light Flasher (Relay On Board)
 Plug In Dual Stage Shock Sensor (Pre-detect, Full Trigger and “City Mode”)
 Audible Arm, Disarm, Defect, and Tamper Chirp Indications
 Headlight Control Output
 Illuminated Entry Control Output
 Active or Passive Arming Selectable
 Programmable Auto Lock On / Off
 Programmable Auto Unlock On / Off/Drivers Door/All Doors
 Programmable Door Lock Pulse Duration 1 Second / 3.5 Seconds/1 Sec

L/ Dbl. U/L

 Programmable Active or Passive Door Locks
 User Programmable Permanent Chirp Delete
 On Command RF Chirp Delete from Transmitter Or Selectable Through

Software

 Dome Delay Learn Circuitry (Patented)

OPTIONS :

 Telematic Upgrade Ready
 Plug In Flash Logic By-Pass Capable
 Remote Trunk Release (must have electric trunk release)

 Remote Keyless Entry (must have power door locks)
 Multiple Vehicle Capable
 Remote Power Window Roll Up

CAUTION! Be certain that the vehicle is outdoors before using this or any remote

YOUR “CODE HOPPING“ TRANSMITTERS

The transmitters included with your new security system use the most advanced
and secure form of radio frequency transmission available on any current auto­motive security system. Some of today’s sophisticated auto thieves use a device
known as a code grabber, which will receive and store the signal from your
keychain transmitter and re-transmit at a later time to disarm your system.

Your Keeloq Code Hopping transmitters will change their signal every time the
button is pressed, so when a thief grabs then re-transmits your signal, the alarm
system will not respond.

If your transmitter button is pressed more than fifty times while it is out of range of
the vehicle (children playing with your keys), the transmitter will not operate when
you return to the vehicle, and will need to be re-aligned to the receiver. To do this,

vehicle starting device. A running engine produces dangerous car­bon monoxide fumes which can be harmful or fatal if prolonged expo­sure occurs. DO NOT remote start the vehicle if it is garaged.

Page 2

128-7863

2 of 20

simply press button 1, (lock), two times within a one second time period. The
system will now respond to that transmitter each time a button is pressed.

NOTE: This system is custom configurable and can be set up to operate with a

2. Press and release Lock/Arm button on the keychain transmitter.

NOTE: If the optional Headlamp illumination feature has been added, and has

SILENT ARMING - ACTIVE (Must be activated during programming)

number of options controlled from any transmitter button or button com­bination. For reference, we will describe operation assuming that your
system is programmed for separate lock and unlock but­tons. Also reference will be made to the icons as shown
on the buttons left.

been selected for operation when arming, as an added convenience, the
system will turn on the headlights when the system is armed.

1. Turn off the engine, exit the vehicle and close all doors, hood lid and trunk lid.

2. Press and hold the Lock/Arm button on the keychain transmitter for 2
seconds.

 The dash mounted LED begins to flash slowly.
 Parking Lights flash one time.
 Siren will not sound.

If the siren "chirped" three times, sometime after arming, the exclusive delayed
dome light learn circuit has been programmed and the system detected a open
entry point after the learned delay expired. Closing the hood, trunk, or doors will
correct the problem and you do not need to disarm the system to make the
correction.

NOTE: The LCD based remote will be explained in
detail further in this manual See "System Status"
described later in this manual. Consult your instal­lation center if your system has been configured
differently.

NOTE: Your system has the option of using a siren,
the vehicle horn, or both for the sounding device.
Where the siren is referenced below, the horn or
both may in fact chirp, or beep.

ARMING THE SYSTEM - ACTIVE

1. Turn off the engine, exit the vehicle, and close all
doors, hood lid and trunk lid.

 The dash mounted LED begins to flash slowly.
 Parking Lights flash one time.
 Siren sounds one chirp.

If the siren/horn
hood lid ajar. Simply close the opened entry point to provide full protec­tion. If the siren "chirped" three times, sometime after arming, the
exclusive delayed dome light learn circuit has been programmed and
the system detected a open entry point after the learned delay expired.
Again, closing the hood, trunk, or doors will correct the problem and you
do not need to disarm the system to make the correction. If the siren/
horn did not sound when arming, then the chirps have been turned off
and you should refer to the section titled "ELIMINATING THE ARM/DIS­ARM CHIRPS" in this manual.

 Doors Lock - Optional

sounds 3 chirps, then you have left a door, trunk, or

Page 3

128-7863

3 of 20

 Doors Lock - Optional

NOTE: If the optional Headlamp illumination feature has been added, and has
been selected for operation when arming, as an added convenience, the sys­tem will turn on the headlights when the system is armed.
The LCD Remote has the following response:

ARMING THE SYSTEM - P ASSIVE (AUTOMATIC)

(Must be activated during programming)

1. Turn off the engine, exit the vehicle and close and lock all doors, hood lid and
trunk lid.

 The dash mounted LED begins to flash rapidly, indicating 30 second passive
arming has begun.

2. Opening any protected entry point during the 30 second passive arming cycle
will immediately suspend automatic arming and the 30 second passive arm­ing cycle will re-start when all doors are closed. At the end of the passive
arming cycle;

 The dash mounted LED begins to flash slowly.
 Parking Lights flash one time.
 Siren sounds one chirp

If the siren did not sound when arming, then the chirps have been turned off and
you should refer to the section titled “ELIMINA TING THE ARM / DISARM CHIRPS“
in this manual.
 Doors Lock - Optional
Door locking during passive arming is a selectable feature. The alarm can be
programmed to allow the doors to lock only when arming using the keychain
transmitter and they will not automatically lock during passive arming.

PROTECTION WHILE THE SYSTEM IS ARMED

 Opening any protected door, hood or trunk lid will cause the alarm to imme­diately sound. The alarm will continue to sound for 30 seconds, then stop and
continue to monitor all protected entry points. If the thief left a door opened, the
alarm will sound for six 30 second cycles, remain armed and ignore that trig­gered zone.\

 Whenever the system is armed, the dash mounted LED indicator will slowly
flash. This serves as a visual deterrent to the potential thief. The LED is a very
low current bulb and will not cause the vehicle’s battery to drain, even when left
unattended for extended periods.

 Whenever the system is triggered, the vehicle’s parking lights will flash for the
full 30 second alarm cycle, attracting visual attention to the vehicle.

 Optional - Whenever the system is armed, the vehicle’s starting circuit will be
bypassed. If the thief should choose to ignore the siren, the vehicle can not be
started.

 Any mild impact to the vehicle’s glass will cause the alarm to sound a short
series of warning tones.

 Any strong impact to the vehicle’s glass will cause the alarm to trigger for the
full 30 second alarm cycle.

NOTE: If the optional interior illumination circuit was installed, the interior light

will flash as well for the full 30 second alarm cycle.

DISARMING THE SYSTEM
NOTE: If the optional 2 step door unlock circuit is installed, when the unlock

Page 4

128-7863

4 of 20

transmitter button is activated, the drivers door only will unlock, pressing the
unlock button a second time will cause all doors to unlock.
NOTE: If your transmitter has been configured with single button Lock/Unlock, t o
activate the all door unlock feature operate the Lock/Unlock button a second
time within 3 seconds of the first unlock command.

1. As you approach the vehicle, press and release the Unlock/Disarm button on
the keychain transmitter.

 The dash mounted LED turns off.
The LED will start flashing rapidly, indicating that the system is re-arming
automatically. Open any door to suspend the automatic arming.
 Parking Lights flash two times.
If the parking lights flashed three times, then the alarm was triggered in your
absence. Before turning the key on, examine the LED to identify which zone was
triggered.
 Siren sounds two chirps.
If the siren sounds 4 chirps, then the alarm was triggered in your absence. Before
turning the key on, examine the LED and refer to the INTRUSION WARNING
SIGNALS section of this manual to identify which zone was triggered.
If the siren did not sound when disarming, then the chirps have been turned off
and you should refer to the section titled “ELIMINATING THE ARM / DISARM
CHIRPS“ in this manual.

 Doors Unlock - Optional
 2 Step Doors Unlock - Optional

NOTE: If the optional Headlamp illumination feature has been added and has
been selected for operation when disarming, as an added convenience, the
system will turn on the headlights when the system is disarmed.

SILENT DISARMING (Must be activated during programming)
Note: If the optional 2 step door unlock circuit is installed, when the unlock

transmitter button is activated, the drivers door only will unlock, pressing the
unlock button a second time will cause all doors to unlock.
NOTE: If your transmitter has been configured with single button Lock/Unlock as
shown, to activate the all door unlock feature operate the Lock/Unlock button a
second time within 3 seconds of the first unlock command.

1. Press and hold button the Unlock/Disarm button on the keychain transmitter for

2 seconds.
 The dash mounted LED turns off.
The LED will start flashing rapidly, indicating that the system is re-arming
automatically. Open any door to suspend the automatic arming.
 Parking Lights flash two times.
If the parking lights flashed three times, then the alarm was triggered in your
absence. Before turning the key on, examine the LED to identify which zone was
triggered.
 Siren will not sound.
If the siren sounds 4 chirps, then the alarm was triggered in your absence.
Before turning the key on, examine the LED and refer to the INTRUSION

Page 5

128-7863

5 of 20

WARNING SIGNALS section of this manual to identify which zone was triggered.

 Doors Unlock - Optional
 2 Step Doors Unlock - Optional

NOTE: If the optional Headlamp illumination feature has been added and has
been selected for operation when disarming, as an added convenience, the
system will turn on the headlights when the system is disarmed.

WHILE THE SYSTEM IS SOUNDING

If during a triggered state, you wish to shut off the siren without disarming your
security system, simply press and release any transmitter button other than the
Unlock/Disarm button. This action will turn off the siren yet leave the vehicle fully
armed and protected. This feature is particularly useful if you are aware of children
playing near your vehicle that may accidently trigger your security system. In this
case you can cancel the siren sounding without disarming your alarm.

INTRUSION WARNING SIGNALS

This system will inform you if an intrusion attempt has occurred while you were
away from the vehicle. If an intrusion attempt has occurred, the siren will
chirp 4 times and the parking lights will flash 3 times when disarming the
system. Enter the vehicle and observe the red dash mounted LED to identify
which zone was triggered.

 If the LED is flashing one time...pause...one time...pause...etc., then an

intrusion attempt was made to the shock sensor, or an accessory trigger­ing device that may have been added to the system.

 If the LED is flashing two times...pause...two times...pause...etc., then

an intrusion attempt was made to a hood or trunk pin switch that was
added to the system or to a light activated entry point if the alarm was
installed using the voltage sensing feature.

 If the LED is flashing three times...pause...three times...pause...etc.,

then an intrusion attempt was made through one of the vehicle’s doors.

These intrusion warning indicators are stored in the system’s memory and will
only be erased when the ignition key is turned on.

PUSH-BUTTON LED/V ALET/OVERRIDE/PROGRAMMING SWITCH: (PBLED)

The PBLED switch allows you to temporarily bypass all alarm functions, elimi­nating the need to hand your transmitter to parking attendants or garage me­chanics. When the system is in valet mode, all alarm functions are bypassed,
however the remote panic feature and remote door locks will remain operational.
To use the valet mode, the system must first be disarmed either by using your
keychain transmitter, or by activating your personalized manual override code.

1. Enter the vehicle, and turn the ignition key to the on position.

2. Press and hold the PBLED switch until the LED turns on solid. The system

will remain in the valet mode.

3. To return to normal operation, press and release the PBLED switch any time

the ignition is on.

NOTE: Always remember to return the vehicle to the valet off position. This will

ensure that the vehicle remains protected at all times.

MANUALL Y OVERRIDING YOUR SYSTEM:
USING THE PBLED OVERRIDE SWITCH

Your Security System can be disarmed without the use of the keychain transmit­ter. This is necessary, since you will need the ability to operate your vehicle if the
transmitter is lost or its battery fails. If your system has been selected for Valet
Switch manual override as indicated on the last page of this manual, to bypass
the alarm system:

Page 6

128-7863

6 of 20