Audiovox XM-RCV User Manual

Download

P .

ELECTRONICS COR

XM® SATELLITE DIGITAL AUDIO

RECEIVER SYSTEM MODEL SRXM-001

INSTALLATION MANUAL

FOR USE WITH THE RADIO RECEIVER

UNIT (RRU) MODEL XM-RCV

For Customer Service

Visit Our Website At

999

.audiovox.com

Product Information, Photos,

FAQ’s Owner’s Manuals

INTRODUCTION

The Audiovox Electronics XM® Satellite Digital Audio Control And Receiver System (Model SRXM-001) was developed to allow the user to listen to a huge selection of programming

supplied by a subscription to XM

Radio. (XM®-compatible antenna also required).

The Audiovox Electronics XM installed using the installation instructions herein, and is designed to work with the user’s existing car stereo system through an unused FM frequency or the auxiliary audio inputs. The programming and use of this system is described in detail in the supplied Owner’s Manual.

The Audiovox Electronics XM with a satellite RADIO RECEIVER UNIT (RRU), a SATELLITE SYSTEM CONTROL UNIT (SCU), and a FM MODULATOR/CONTROL INTERFACE unit that allows the user to select an exact XM antly designed and can be mounted in the cab of the vehicle in numerous ways. This Installation Guide depicts typical installation scenarios.

It is important that the installer reads and understands all of the installation procedures for each of the components to be installed, either supplied with the Audiovox Electronics XM Satellite Digital Audio Control and Receiver System (Model SRXM-001) or equipment that

is to be installed in conjunction with the system such as the XM® Antenna.

The Audiovox Electronics XM® Satellite Digital Audio Control and Receiver System (Model SRXM-001) comes with a 36 month limited warranty (see the back cover of the owner’s manual for details)

Radio channel on the easy to read display. The controller is compact, pleas-

Satellite Digital Audio Control And Receiver System is easily

Satellite Digital Audio Control and Receiver System comes

TRADEMARKS

Other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies and are hereby acknowledged.

INSTALLATION and WIRING PRECAUTIONS

1. To prevent a short-circuit, Be sure to turn off the ignition and remove the negative (-)

battery cable, prior to installation. Connect power wires last.

NOTE: If the SRXM-001 System is to be installed in a car that is equipped with an on-board drive or navigation computer, do not disconnect the battery cable. If the cable is disconnected, the computer memory may be lost. Under these conditions, use extra caution during installation not to cause a short circuit.

2. Do not install the unit in the following locations:

Locations exposed to direct sunlight. Where hot air is discharged from the car heater. In areas subject to extreme temperatures.

3. Incorrect installation may cause damage to the system. Mount the unit firmly in place, using

the supplied brackets and screws.

4. Be careful not to damage the car wiring.

5. Be sure to use the supplied screws and washers.

6. Be careful not to snag any wires when tightening screws.

PACKING LIST

RLTO RRUTO SCU

ANT.

POWER

TO CAR

TO RADIO

ANT.

SATELLITE RADIO RF MODULATOR

AUDIO OX

SRXM-001 MAIN SYSTEM COMPONENTS

(NOTE: Components are not drawn to scale.)

RADIO RECEIVER UNIT (RRU)

Model # XM-RCV

AUDIO OX

AUDIO OUT

LR DIN OUTSAT.TER.

1 pc.

INSTALLATION PARTS

RRU Mounting

Brackets

2 pc.

(P/O XM-RCV)

Phillips Round Head

Screw

(4mm x 8mm)

w/ External Tooth Washer

(Used to mount SCU to mounting

surface)

Self-tapping Screws

Flat Washers and Lock Washers

(Used to mount RRU to mounting surface)

SATELLITE SYSTEM CONTROL

UNIT (SCU)

Model # SAT-COM

AUDIO OX

(5mm x 15mm), with

4 pcs. each

(P/O XM-RCV)

Din Cable, 13- pin

(6 Meter)

To connect the RRU to the FM Modula-

tor / Control Interface

SFT

1 pc.

Phillips Round Head

Screw (4mm x 8mm)

(Used to mount

bracket to RRU)

(P/O XM-RCV)

FM MODULATOR /

CONTROL INTERFACE

(P/O SAT-COM)

4 pc.

FM Modulator Control

Interface Wire Harness

1 pc.

Phillips Round

Head. Screw

(4mm x 12mm)

(Used to mount FM MOD

to mounting surface)

4 pc.

(P/O SAT-COM)

4 pcs. each

(P/O XM-RCV)

1 pc.

(P/O XM-RCV)

1 pc.

(P/O SAT-COM)

RCA to RCA Cable

To connect the RRU to the FM Modula-

(6 Meter)

tor / Control Interface

1 pc.

(P/O XM-RCV)

Hook & Loop

SUPPLIED

ACCESSORIES

Quick

Reference

Card

Owner's

Manual

OPTIONAL

ACCESSORIES

Trim Ring,

Satellite Control

Model #SAT-PF

Satellite Radio

Wireless Remote

Control Model

#SAT-RC

Adhesive Tape

1 cut set.

(P/O SAT-COM)

1 pc.

(P/O SAT-COM)

1 pc.

(P/O SAT-COM)

TYPICAL FM MODULATED SYSTEM

INSTALLATION

SFT

AUDIO OX

IMPORTANT - Some vehicles use a special dual antenna “Diversity" system.

If the vehicle into which this system is being installed has this type of antenna

system, the antenna cable will not fit the socket on the FM modulator. Use

of the SRXM-001 system with “Diversity" systems is not recommended. You

may also find some cars have an antenna plug that is too small to mate with

the socket on the FM modulator. If this is the case, call Audiovox’s Toll-Free

Assistance for a special adaptor. This adaptor can also be purchased at most

car stereo installation centers.

Ouput to the RF Mododulator Audio Input.

with system) used to connect the RRU Audio

NOTE: “B” RCA to RCA Cable (supplied

*Yellow = Satellite connection

*Green =Terrestrial connection

(Sold separately)

NOTE: “A” To Satellite Radio Antenna

connect the FM Modulator to the RRU,

NOTE: “C” Before routing the Din Cable to

connector is matched to the RRU.

matched to the FM Modulator and the Black

unnecessary re-work. The Gray connector is

observe the color code to avoid any

R L

AUDIO OUT

AUDIO OX

TER. SAT. DIN OUT

TO SCU

RLTO RRU

POWER

ANT.

AUDIO OX

TO RADIO

SATELLITE RADIO RF MODULATOR

ANT.

TO CAR

TYPICAL AUXILLARY AUDIO SYSTEM

INSTALLATION

SFT

AUDIO OX

IMPORTANT - Some vehicles use a special dual antenna “Diversity" system.

If the vehicle into which this system is being installed has this type of antenna

system, the antenna cable will not fit the socket on the FM modulator. Use

of the SRXM-001 system with “Diversity" systems is not recommended. You

may also find some cars have an antenna plug that is too small to mate with

the socket on the FM modulator. If this is the case, call Audiovox’s Toll-Free

Assistance for a special adaptor. This adaptor can also be purchased at most

car stereo installation centers.

*Yellow = Satellite connection

*Green =Terrestrial connection

(Sold separately)

NOTE: “A” To Satellite Radio Antenna

Ouput to the Radio Reciever Auxilary Input.

with system) used to connect the RRU Audio

NOTE: “B” RCA to RCA Cable (supplied

connect the FM Modulator to the RRU,

NOTE: “C” Before routing the Din Cable to

Output to the Radio Reciever Auxilary Input.

with system) used to connect the RRU Audio

RCA to 1/8” Stereo Plug Cable (not supplied

-or-

connector is matched to the RRU.

matched to the FM Modulator and the Black

unnecessary re-work. The Gray connector is

observe the color code to avoid any

R DIN OUT

AUDIO OUT

AUDIO OX

TER. SAT. L

POWER

TO RRU

LTO SCU

AUDIO OX

ANT.

TO RADIO

SATELLITE RADIO RF MODULATOR

ANT.

TO CAR

TYPICAL FM MODULATED INSTALLATION for SRXM-001 SYSTEM COMPONENT LAYOUT

Ground (BLACK)

Attach this wire to the chassis of the car. Be sure that the surface is free of paint and is not rusty. If a proper ground connection is not made, the SRXM-001 System may not operate correctly and stray noise may be picked up by the unit.

To FM Radio Antenna input

+12V Battery

(YELLOW)

Connect this wire to a terminal which is always energized.

FM Modulator

FM Radio

SCU

From Existing Vehicle Antenna

Satellite Radio

Antenna

(Purchased Separately)

DIN Cable

Filter Box & Fuses

+12V Accessory / Ignition (RED)

Connect this wire to a terminal which is energized when the ignition switch is turned to the "ON" or "ACCESSORY" position.

MOUNTING THE FM MODULATOR

Install the FM Modulator to the mounting surface with the self-tapping screws (4mm x 12mm).

RRU

RCA to RCA

Cable

13-Pin

DIN Cable

Self-Tapping Phillips Head Screw

SYSTEM INSTALLATION

RADIO RECEIVER UNIT (RRU)

PROCEDURE for HORIZONTAL INSTALLATION of the RRU

Attach the mounting brackets to each side of the RRU, using the 4 Phillips Round Head

Screws (4mm x 8mm).

Bracket

Phillips Head Screws (4mm x 8mm) used in 4 places

Determine the mounting location and drill 4x 1/8” (4mm) mounting holes.

WARNING

Never mount the unit near the fuel tank.

4x 1/8” (4mm) mounting holes

NOTE:If mounting surface is carpeted, use caution when drilling holes to prevent drill bit from catching on carpet. Cut holes in carpet before drilling into subsurface.

Mount the unit in place, using 4 Self-tapping Screws (5mm x 15mm), w/Flat Washers and

Carpet

Lock Washers. Use RTV (silicone sealer) on screw threads or around the holes to prevent moisture intrusion.

RRU

Self-tapping Screw (5mm x 15mm), w/Flat Washers and Lockwashers used in 4 places

Bracket

Carpet

PROCEDURE for VERTICAL INSTALLATION of the RRU

Attach a mounting bracket to each side of the RRU, using the 4 Phillips Round Head

Screws (4mm x 8mm).

RRU

Phillips Head Screws (4mm x 8mm) used in 4 places

Bracket

Determine the mounting location and drill 4 x 1/8” (4mm) mounting holes.

WARNING

Never mount the unit near the fuel tank.

4x 1/8” (4mm) mounting holes

Carpet

NOTE: If mounting surface is carpeted, use caution when drilling holes to prevent drill bit from

catching on carpet. Cut holes in carpet before drilling into subsurface.

Mount the unit in place, using 4 Self-tapping Screws (5mm x 15mm), w/Flat Washers and Lock

Washers. Use RTV (silicone sealer) on screw threads or around the holes to prevent moisture intrusion.

Self-tapping Screw (5mm x 15mm), w/Flat Washers and Lockwashers used in 4 places

Bracket

RRU

Carpet

PROCEDURE for the MOUNTING of the RRU UNDER THE REAR DECK

Attach the mounting brackets to each side of the RRU, using the 4 Phillips Round Head

Screws (4mm x 8mm).

Bracket

Phillips Head Screws used in 4 places (4mm x 8mm)

Determine the mounting location and drill four 4mm mounting holes.

Underside of Rear Deck

4x 1/8” (4mm) mounting holes (4 places)

Mount the unit in place, using 4 Self-tapping Screws (5mm x 15mm), w/Flat Washers and

Lock Washers.

Rear Deck

Self-tapping Screw (5mm x 15mm), w/Flat Washers and Lockwashers used in 4 places

INSTALLING THE SATELLITE SYSTEM CONTROL UNIT (SCU)

PROCEDURE for a TYPICAL INSTALLATION of the SCU USING HOOK & LOOP ADHESIVE TAPE (SUPPLIED)

1. Determine where the SCU is to be located (flat surface) NOTE: The chosen position must allow a clear view of the display and easy access to the controls for both the Driver and Passenger of the vehicle.

2. Using an Alcohol Swab, clean and dry the entire surface area where the SCU is to be mounted and the back surface of the SCU.

3. Remove the protective paper from the back of the first piece of the supplied Hook & Loop Adhesive Tape (Loop side) and apply it to the mounting surface (see Figure 1.)

4. Remove the protective paper from the back of the second piece of the supplied Hook & Loop Adhesive Tape (Hook side) and apply it to the back side of the SCU (see Figure 2.). Position the SCU cable in the appropriate directional channel on the back of the SCU so that the back surface is flat (see Figure 3.).

5. Carefully press the SCU into place.

Velcro Tape (Loop)

Figure 1.

Hook & Loop Adhesive Tape (Hook)

Figure 2.

NOTE:

Figure 3.

Do not install the unit in the following locations: In Locations exposed to direct sunlight. Where hot air is discharged from the car heater. In areas subject to extreme temperatures.

PROCEDURE FOR A TYPICAL BRACKET INSTALLATION OF THE SCU

SFT

(Bracket not supplied)

Audiovox suggests this type of installation over the Hook & Loop type of installation though the Hook & Loop installation (if done correctly) is a secure and sufficient mounting option. Installation of the SCU using a bracket results in a professional, factory-installed look, without visibly damaging the interior of the vehicle. When combined with the optional Trim Ring (model #SAT-PF) the results are further cosmetically enhanced. There are several types of brackets available to accomplish this type of installation.

The installation procedure that follows, illustrates the use of a Pro.Fit found that the Pro.Fit

VSM® line of mounting brackets are easy to install and compliments the installation of the SCU as well as being a perfect match to the optional Trim Ring (model #SAT-PF). Pro.Fit® VSM mounting bracket reduce the installation liability while maintaining the resale value of a car because of the professional fit, professional look and safe design.

Currently Pro.Fit

VSM® offers hundreds of brackets, covering most popular cars, vans, and trucks. Step-

by-step instructions and technical support are available for every mount and application. After the proper mounting bracket has been selected and installed using the Original Manufacturers

installation instructions, proceed with the following steps:

1. Feed the SCU Cable through the hole in the Trim Ring (optional) and connect it to the RF Modulator.

2. Using the Phillips Head Screws and the External Tooth Lock Washers (supplied),

Mount the SCU to the bracket as shown in the Figure below. NOTE: Use caution not to over tighten the screws into the back of the SCU as this may

cause damage to the unit.

NOTE:

Do not install the unit in the following locations: In Locations exposed to direct sunlight. Where hot air is discharged from the car heater. In areas subject to extreme temperatures.

mounting bracket. Audiovox has

(Example installation position)

Phillips Round Head Screw (4mm x 8mm)

External Tooth Washer

(4mm int.)

Bracket

Bracket Shown is a PRO.FIT for ordering information

(Not Supplied)

visit www.pro-fit-intl.com

SCU

Trim Ring

(Not Supplied, Model #SAT-PF)

For ordering information call Audiovox Electronics toll-free telephone assis-

tance line at 1-800-645-4994 or contact us via the web:

www.audiovox.com

Upon completion of the SCU installation and before the XM radio is activated a test of the system should be performed. To verify that the SRXM-001 system and the antenna have been installed correctly and are functioning, select and listen to CH 1. (XM preview channel). If there is no power to the SCU check that all connections have been made and that fuses are good. If there is no signal present, make sure that the antenna is unobstructed (move vehicle) and check the antenna cable connection to the RF Modulator. For a detailed trouble-shooting guide, refer to the Owner’s Manual.

128-6213A

Audiovox XM-RCV User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual