Audiovox VX4022 Installation Manual
VX7022/VX4022/DMX5022
Installation Guide
What’s in the Box The
following items are supplied with
e VX7022/VX4022/DMX5022:
th
• HeadUnit
• TrimRing
• HardwareBag
• Power/SpeakerOutputHarness
• RemoteControl
• ExternalMicrophone
• InstallationGuide
WARNING!Neverinstallthisunitwhereoperationandviewingcouldinterferewith
safedrivingconditions.
tools and supplie are needed to install the
head unit:
• Torx type, flat-head and Philips
• Wire cutters and strippers
• Tools to remove existing radio (screw
• Electrical tape
• Crimping tool
• Volt meter/test light
• Crimp connections
• 18 gauge wire for power connections
• 16 – 18 gauge speaker wire
Tools and Supplies The following
screwdrivers
, socket wrench set or other
driver
tools)
DASHBOARD
TAB
Step 1-b
Step 1-c
Step 2
Step 5-c
Optional Equipment
Steering Wheel Control Interface (SWC) - The VX7
iDatalink Maestro SW
steering wheel control adapters.
022/VX4022/DMX5022 are compatible with various PAC, Metra and
Disconnect the Battery
To prevent a short circuit, be sure to turn off the ignition and remove the negative (-) battery cable prior to installation.
•
NOTE: If the head unit is to be installed in a car equipped with an on-board drive or navigation computer, do not
disconnect the battery cable. If the cable is disconnected, the computer memory may be lost. Under these conditions,
use extra caution during installation to avoid causing a short circuit.
Replacing the Fuse
•
When replacing the vehicles Radio fuse always use the proper rated replacement fuse. Using a fuse with an improper rating
could damage the unit and cause a fire.
ISO-DIN Installation
The head unit is designed to fit into a 2.0 DIN dashboard opening. The unit has threaded holes in the chassis side panels which
may be used
mount the radio to the dashboard. Please consult with your local car stereo specialty shop for assistance on this type of
installation.
1. Remove the existing factory radio from the dashboard or
2.
Remove the factory mounting brackets and hardware from the
existing radio and attach them to the new radio.
CAUTION! Do not exceed M5 X 6MM screw size. Longer
screws may damage components inside the chassis.
with the original factory mounting brackets of some Toyota, Nissan, Mitsubishi, Isuzu, Hyundai and Honda vehicles to
center console mounting. Save all hardware and brackets as
they will be used to mount the new radio.
3.
Place the radio in front of the dashboard opening so the wiring
can be brought through the mounting sleeve. Follow the
wiring diagram carefully
secure and insulated with wire nuts or electrical tape. After
completing
the mating socket on the rear of the chassis. Turn the unit
to confirm
the unit does not operate, re-check all wiring until the problem
is corrected.
4.
Mount the new radio assembly to the dashboard or center
console using the reverse procedure in step 1 above.
CAUTION! Be careful not to damage the car wiring.
NOTE: It is the end-users responsibility to install and operate this unit in a manner in accordance with local, state and federal
laws. The PARKING BRAKE wire MUST BE CONNECTED as directed in the manual.
the wiring connections, plug the connector
operation (vehicle ignition switch must be “ON”). If
and make certain all connections are
into
on
Using the Cosmetic Trim Ring
A cosmetic trim ring is supplied with the head unit for installation
flexibility. This unit will fit into most import dashes with little or
no modification to the dash board/cavity. Some US domestic
vehicle dashes will accept a Double-DIN chassis, but there is
usually a small gap between the radio and dash piece after
installation is complete. In this case, use the trim ring to conceal
any gaps that may be present.
NOTE: For proper operation of the CD/DVD player, the chassis must be mounted within 30° of horizontal. Make sure the
unit is mounted within this limitation.
2
Loading...