Audiovox VOH682A, VOH681A INSTALLATION GUIDE
VOH681A Drop Down Video Monitor
VOH682A Drop Down TV / Video Monitor
AUTOON OFF
OPEN
Installation Guide
Important Notice
It is unlawful in most jurisdictions for a person
to drive a motor vehicle which is equipped
with a television viewer or screen that is
located in the motor vehicle at any point
forward of the back of the driver's seat, or
that is visible directly or indirectly to the
operator of the motor vehicle.
Please note that the state of Rhode Island
forbids the installation of such a device in a
motor vehicle.
MATERIALS INCLUDED IN THIS PACKAGE:
3c
1) VOH681A V ideo Monitor with out TV T uner / VOH682A Video Monitor with TV Tuner (1 pc)
2) Accessory Harness (P/N 8010730) (1 pc)
3) 12 Pin Power / Signal harness (P/N 112B2821) (1 pc)
4) 2 Pin Power Wire Harness with choke (P/N 112B2824) (1 pc)
5) RCA “Y” Adapter (1 Male to 2 Female) (P/N 0892165) (1 pc)
6) Hardware Package
#4 x 3/8” Screws (12 pcs)
#8 x 5/8” Self Drilling Screws (4 pcs)
#8 Washers (4 pcs)
7) Remote Control (P/N 1361612 supplied with VOH682A only)
8) Protective Cover for External A / V Inputs (P/N 1023336)
3
1
AUTOON OFF
OPEN
2
3b
3a
3c
3e
3d
3f
4
CHOKE
TOOLS REQUIRED:
#2 Phillips Screwdriver
#1 Phillips Screwdriver
Utility or Razor Knife or Shears
Wire Strippers
Upholstery hook tool (for removal of panels as necessary)
Electrical Tape
Masking Tape
Multimeter (to verify 12 volt DC and continuity: Do not use a test light or logic probe)
Marker pen – to mark headliner
Scribe (to mark trim ring if used)
Misc. electrical connectors (to connect to vehicle power source). Requirements will vary from
vehicle to vehicle)
Video tape (to verify system operation after installation)
3
6
3
3e
5
3a
3a
7
8
-1-
GENERAL INSTALLATION APPROACH:
1) Decide upon system configuration and options that will be installed (i.e.: what components, VCP,
Tuner, RF Modulator/external amp, remote headphones, 2
2) Review all manuals to become familiar with electrical requirements and hook ups.
3) Decide upon mounting locations of all components and method of mounting.
4) Prep the vehicle by removing any interior trim necessary to gain access to vehicle's wiring as well as
all areas where interconnecting wire harnesses will need to be located. If any access holes need to be
cut into the vehicle (headliner, other trim components etc.), this should be done now as well. (Refer to
Page 3).
5) Route the wiring harnesses throughout the vehicle as necessary. (Refer to the Wiring Diagrams on
pages 6 and 7 of this manual as well as the wiring instructions for the individual components and
accessory options being installed). Be sure that all wiring is protected from sharp edges and is routed
in such a manner that it will not be pinched when all components and interior trim are fully installed. Be
sure to leave enough slack in the wiring at each component to allow working room.
6) Remove all A/V system components from their packaging and place them loosely in the vehicle at
their respective locations.
7) Connect all components together (electrically) and verify proper operation of all system functions.
Note: This is best done BEFORE, components have been permanently mounted.
8) After verifying proper operation of the system, proceed to mount of each component.
9) When all components are mounted, recheck function of entire system again to ensure that no wiring
was pinched or connected improperly during final installation.
nd
VCP, etc.).
GENERAL SYSTEM CONFIGURATIONS:
The following is intended to give a rough guideline of system configurations that are possible with the
VOH681A and VOH 682A series Drop Down Video Systems:
System 1: Video Monitor without tuner (VOH681A), VCP .
-All wiring necessary is included with this package.
-Headphones are connected into the headphone jacks on the monitor itself.
System 2: Video Monitor with tuner (VOH682A), VCP
-Same as system 1, but TV antenna must be added (AN-300 or similar).
System 3: Video Monitor (VOH681A), VCP , 2nd VCP (or other A/V component)
-Same as system 1 but extra Source Component (PN 8010730) Harness must be purchased.
System 4: Video Monitor / TV (VOH682A), VCP, 2nd VCP (or other A/V component)
-Same as system 3, but TV antenna must be added (AN-300 or similar).
Notes:
-All systems have built-in game/camcorder inputs (the A/V input jacks on the video monitor itself).
-There are a few audio output options that can be added as follows:
a) Remote headphone jacks can be added to a VOH681A system. Refer to the wiring
diagram on p6.
b) Additional speakers can be added to a VOH682A system using the speaker outputs. Refer to the
wiring diagram on p7.
-The VOH681A and VOH 682A video systems are only intended for an overhead, drop down installation. It
is not intended for seat back or any other type of mounting. The hinging mechanism is designed for
horizontal, drop down use only .
-2-
Loading...