Audiovox VOH1332 User Manual
VOH1332
Owner’s/Installation
Manual
13.3” Flip-Down In Vehicle
Entertainment System
Audiovox Electronics Corporation
150 Marcus Blvd.
Hauppauge, NY 11788
1-800-645-4994
Features
- TFT Active Matrix Color 13.3” LCD
- 3 Channel A/V Switching Built-In
- Audio Amplifier, Volume Control, and Headphone Jacks Built-In
- Game/Camcorder A/V Input Jacks
- Backlit Controls for easy Night Operation
- “Hide-Away” Screen when not in Use
- Built-In TV Tuner
- Infrared Remote Control Repeater Circuit (for Wireless VCP, and Tuner Functions)
(VCP must be purchased separately)
C1
Package Contents
A) VOH1332 Video Flip Down Pod- (p/n VOH1332)
(not shown)
B) Source Component Harness- (p/n 8010730)
C) Accessory Bag-
1. Power harness (15ft.)
2. Audio “Y” Patch Cord Adapter- (p/n 0892165)
3. #10 x 1 ¼” Self-drilling Screws- (Qty. 8)
D) Owner’s/Installation Manual (not shown)
E) Remote Control
C
E
C2
C3
B
Tools Required
- #2 Phillips Screwdriver
- Wire Strippers
- Masking Tape
- Multimeter (to verify 12VDC and continuity, do not use test light)
- #1 Phillips Screwdriver
- Utility Knife
- Electrical Tape
- Misc. electrical connectors (to connect to the vehicle power source…. Will vary from vehicle
to vehicle)
- Video tape (to verify function of the system after installation)
2
Rear Panel Feature
467
1111
5
11
12
8
9
10
12
1
3
2
11
1) Left RCA Out: Hook-up for left audio out (white female RCA jack)
2) Right RCA Out: Hook-up for right audio out (red female RCA jack)
3) Video Out: Hook-up for video out (yellow female RCA jack)
4) Power Harness Connection: This plug connects to the power harness mating plug
5) Optional Wired Headphone Connections: Green is right positive, Gray is left positive and
Black is the ground. Minimal load requirement is 4Ω. Additional speakers or amplifiers can
be added to the system at this connection point.
6) Antenna Connections: This connects to the antenna if applicable.
7) DIN Connectors: The source component harness (P/N 8010730) connects here. A cable tie
will mount through holes provided in PCB, and is recommended for wire strain relief. A
second component harness is needed to utilize both mini-din connectors.
8) Right Audio In: Use to hook-up Game/Camcorder or DVD (red female RCA jack)
9) Left Audio In: Use to hook-up Game/Camcorder or DVD (white female RCA jack)
10) Video In: From Game/Camcorder or DVD (yellow female RCA jack)
11) Mounting location: Panel mounting locations
12) Headphone Out: Additional headphone out jacks for wired headphones.
3
Front Button Panel Features
123456789
1) Power: This button turns the VOH1332 on and off. Dimly lit when in stand-by mode.
2) Channel ∆ ∇: Pressing ∆ will select higher programmed channels and pressing ∇ will select
lower programmed channels than current channel.
3) Volume ∆ ∇: Pressing ∆ will raise the volume and pressing ∇ will lower the volume.
4) Select: Each press of this button selects the next source (1-3). Note that some sources
produce an image, depending upon whether components are connected to all sources.
5) Latch: Sliding this latch forward will release the 13.3” monitor to drop into playing position.
6) AP: Places the tuner in auto-program mode. Auto program will scan all channels available
and store active channels into memory for easy selection with the channel up/down buttons.
7) Bright ∆ ∇: Pressing this button ∆ will increase monitor brightness, and pressing this button ∇
will decrease monitor brightness.
8) Contrast ∆ ∇: Pressing this button ∆ will increase picture contrast, and pressing this button ∇
will decrease contrast.
9) Color ∆ ∇: Pressing this button ∆ will increase color separation and pressing this button ∇ will
decrease color separation.
4
General Installation Approach
1) Before beginning installation, please refer to warning on page 10.
2) Decide upon system configuration and options that will be installed (ie: what components,
VCP, remote headphones, 2nd VCP, etc.).
3) Review all manuals to become familiar with electrical requirements and hook ups.
4) Decide upon mounting locations of all components and method of mounting.
5) Prep the vehicle by removing any interior trim necessary to gain access to vehicle power
hook up point as well as all areas where interconnecting wire harnesses will need to be
located. If any access holes need to be cut into the vehicle (headliner, other trim
components, etc.) this should be done now as well. Refer to page 4.
6) Route the wiring harnesses throughout the vehicle as necessary. (Refer to the wiring
diagram on pages 5 and 6 of this manual as well as the wiring instructions for the individual
components and accessory options being installed). Be sure that all wiring is protected from
sharp edges and is routed in such a manner that it will not be pinched when all components
and interior trim are fully installed. Be sure to leave enough slack in the wiring at each
component to allow working room.
7) Remove all A/V system components from their packaging and place them loosely in the
vehicle at their respective locations.
8) Connect all components together (electrically) and verify proper operation of all system
functions. NOTE: This is best done both BEFORE and AFTER all components have been
permanently mounted.
9) After verifying proper operation of the system, proceed with mounting of each component.
10) When all components are mounted, recheck function of entire system again to ensure that no
wiring was pinched or connected improperly during final installation.
Notes
- Connecting to both the Wireless Headphones IR Transmitter and a FM Modulator will require
an additional RCA Adapter (P/N 0892165).
- One dual RCA Patch Cord is needed to connect the TV/Monitor to the Wireless Headphone
IR Transmitter.
- One dual RCA Patch Cord is needed to connect the TV/Monitor to the FM Modulator, and is
included in the FM Modulator package (P/N 1070610).
- For audio output, there are a few scenarios that may apply to your system:
a) Remote headphone jacks may be added and located throughout the vehicle.
b) Additional speakers and amplifiers may be added throughout the vehicle.
5
Loading...