Audiovox VE1040 User Manual
Video Cassette Recorder
User’s Guide
AVR-1040
DV-T27N-SJ 99.11.26 5:3 PM ˘`A1
have it replaced by your service technician
7 Power-Cord Protection- Power-supply cords should be routed so that they are not likely to be
walked on or pinched by items placed upon or against them, paying particular attention to
cords at plugs, convenience receptacles, and the point where they exit from the video product.
8 Ventilation- Slots and openings in the case are provided for ventilation to ensure reliable
operation of the video product and to protect it from overheating. These openings must not be
blocked or covered. The openings should never be blocked by placing the video product on a
bed, sofa, rug, or other similar surface. This video product should never be placed near or
over a radiator or heat register. This video product should not be placed in a built-in
installation such as a bookcase or rack unless proper ventilation is provided or the video
product manufacturer’s instruction’s have been followed.
9 Attachments- Do not use attachments unless recommended by the video product manufacturer
as they may cause hazards.
10 Water and Moisture- Do not use this video product near water- for example, near a bath tub,
wash bowl, kitchen sink or laundry tub, in a wet basement, or near a swimming pool and the
like. Caution : Maintain electrical safety. Powerline operated equipment or accessories
connected to this unit should bear the UL listing mark or CSA certification mark on the
accessory itself and should not be modified so as to defeat the safety features. This will help
avoid any potential hazard from electrical shock or fire. If in doubt, contact qualified service
personnel.
11 Accessories- Do not place this video product on an unstable cart, stand, tripod, bracket, or
table. The video product may fall, causing serious injury to a child or adult as well as serious
damage to the video product. Use this video product only with a cart, stand , tripod, bracket,
or table recommended by the manufacturer or sold with the video product. Any mounting of
the product should follow the manufacturer’s instructions and use a
mounting accessory recommended by the manufacturer.
11A A video product and cart combination should be moved with care. Quick
stops, excessiveforce, and uneven surfaces may cause the video product
and cart combination to overturn.
Note to CATV system installer
This reminder is provided to call the CATV system installer’s attention to Section 820-40 of the NEC
which provides guidelines for proper grounding and, in particular, specifies that the cable ground shall
be connected to the grounding system of the building, as close to the point of cable entry as practical.
12
Outdoor Antenna Grounding- If an outside antenna or cable
system is connected to the video product, be sure the antenna
or cable system is grounded so as to provide some
protection against voltage surges and built-up static charges.
Section 810 of the National Electrical Code, ANSI/NFPA No.
70-1984 (Section 54 of
Canadian Electrical Code, Part 1)
provides information with respect to proper grounding of
the mast and supporting structure, grounding of the leadin wire to an antenna-discharge unit, connection to
grounding electrodes, and requirements for the grounding electrode. See example as shown.
Safety information
ANTENNA DISCHARGE UNIT
(NEC SECTION 810-20)
ANTENNA LEAD
IN WIRE
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250 PART H)
GROUND CLAMP
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
EXAMPLE OF ANTENNA
GROUNDING
NEC - NATIONAL ELECTRICAL CODE
Safety information,continued
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE
COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert
the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure
that may be of sufficient magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and servicing instructions in the literature accompanying
the appliance.
WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPLIANCE TO RAIN OR MOISTURE.
CAUTION : TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT,
FULLY INSERT.
IMPORTANT SAFEGUARDS
In addition to the careful attention devoted to quality standards in the manufacture of your video
product, safety is a major factor in the design of every instrument. However, safety is your
responsibility too. This sheet lists important information that will help to assure your enjoyment
and proper use of the video product and accessory equipment. Please read them carefully
before operating and using your video product.
Installation
1 Read and Follow Instructions- All the safety and operating instructions should be read before the
video product is operated. Follow all operating instructions.
2 Retain Instructions- The safety and operating instructions should be retained for future reference.
3 Heed Warnings-Comply with all warnings on the video product and in the operating instructions.
4 Polarization- This video product is equipped with a polarized alternating -current line plug (a plug
having one blade wider than the other). This plug will fit into the power outlet only one way.
This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the
plug. If the plug still fails to fit, contact your electrician to replace your obsolete outlet. To prevent
electric shock, do not use this polarized plug with an extension cord, receptacle, or other outlet
unless the blades can be fully inserted without blade exposure. If you need an extension cord, use
a polarized cord.
5 Power Sources-This video product should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of power supply to your home,
consult your video dealer or local power company. For video products intended to operate from
battery power, or other sources, refer to the operating instructions.
6
Overloading- Do not overload wall outlets of extension cords as this can result in a risk of fire or
electric shock. Overloaded AC outlets, extension cords, frayed power cords, damaged or cracked
wire insulation, and broken plugs are dangerous. They may result in a shock or fire harzard.
Periodically examine the cord, and if its appearance indicates damage or deteriorated insulation,
i
ii
DV-T27N-SJ 99.11.26 5:17 PM ˘`A2
Contents
Overview of the equipment..................................................... 1
Front panel ...............................................................................................................1
Front panel display....................................................................................................2
Back panel................................................................................................................3
Remote control.........................................................................................................4
Connecting your VCR................................................................. 7
Connecting an antenna to the VCR ...........................................................................7
Connecting your VCR to your TV...............................................................................8
Connecting a cable system ......................................................................................10
Setting up your VCR................................................................ 12
Turning the VCR on ................................................................................................12
Changing the on-screen menu language..................................................................12
Setting the clock......................................................................................................13
Selecting cable or antenna viewing..........................................................................14
Programming the channel memory .........................................................................14
Setting the Cabel Box (Cable Box Setup) ................................................................17
Using video cassettes.............................................................. 18
Protecting video cassettes from accidental erasure.................................................18
Inserting /Removing video cassettes ........................................................................18
Watching recorded programs................................................19
Playing a video cassette ...........................................................................................19
Searching forward while viewing a video cassette ...................................................19
Searching backward while viewing a video cassette ................................................19
Pausing a video cassette during playback................................................................19
Stopping video cassette playback ............................................................................19
Fast forwarding the video cassette...........................................................................19
Rewinding the video cassette...................................................................................20
Slow motion/Adjusting the picture ..........................................................................20
Recording programs ................................................................21
Preparing to record a pogram.................................................................................21
Manual recording....................................................................................................21
Timer recording......................................................................................................22
Reviewing timer programs......................................................................................24
Cancelling timer programs......................................................................................24
One touch timer recording .....................................................................................25
Using advanced features ........................................................26
Play the tape automatically ......................................................................................26
Switch the VCR to TV or VCR mode automatically ...................................................26
Searching a cassette tape for programs (indexing).................................................27
Searching with the tape counter (go-to search)......................................................27
Marking a tape for zero search/Child Lock.............................................................28
CM Skip/Display/Daylight-Saving Time....................................................................29
Duplicating video cassette tapes with another VCR..................................................30
Connecting a Audio system to this VCR....................................................................31
Glossary.................................................................................... 32
Troubleshooting.......................................................................33
Specifications .............................................................................35
13
Power Lines- An outside antenna system should not be located in the vicinity of overhead power
lines, other electric light or power circuits, or where it can fall into such power lines or circuits.
When installing an outside antenna system, extreme care should be taken to keep from touching
or approaching such power lines or circuits as contact with them might be fatal. Installing an
outdoor antenna can be hazardous and should be left to a professional antenna installer.
Use
14 Cleaning- Unplug this video product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
15 Object and Liquid Entry-Never push objects of any kind into this video product through
openings as they may touch dangerous voltage points or “short-out” parts that could result in
a fire or electric shock. Never spill liquid of any kind on the video product.
16 Lightning-For added protection for this video product during a lightning storm, or when it is
left unattended and unused for long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent damage to the video product due to
lightning and power line surges.
Service
17 Servicing-Do not attempt to service this video product yourself as opening or removing covers
may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service
personnel.
18 Conditions Requiring Service-Unplug this video product from the wall outlet and refer servicing
to qualified service personnel under the following conditions.
A. When the power-supply cord or plug is damaged.
B. If liquid has been spilled, or objects have fallen into the video product.
C. If the video product has been exposed to rain or water.
D. If the video product does not operate normally by following the operating instructions.
Adjust only those controls that are covered by the operating instructions. Improper
adjustment of other controls may result in damage and will often require extensive work by
a qualified technician to restore the video product to its normal operation.
E. If the vido product has been dropped or the cabinet has been damaged.
F.
When the video product exhibits a distinct change in performance-this indicates a need for
service.
19 Replacement Parts-When replacement parts are required, have the service technician verify
that the replacements he uses have the same safety characteristics as the original parts. Use of
replacements specified by the video product manufacturer can prevent fire, electric shock, or
other hazards.
20 Safety Check- Upon completion of any service or repairs to this video product, ask the service
technician to perform safety checks recommended by the manufacturer to determine that the
video product is in safe operating condition.
21 Wall or Ceilling Mounting- The product should be mounted to a wall or ceilling only as
recommended by the manufacturer.
22 Heat-The product should be situated away from heat sources such as radiators, heat registers,
stoves, or other products (including amplifiers) that produce heat.
iii.
Safety information, continued
DV-T27N-SJ 99.11.26 5:3 PM ˘`A4
1 2
8 RECORD/OTR
Press to record the program currently airing on
the channel. Press multiple times to process one-
.touch-recording (OTR) time options.
9 Remote Sensor
This sensor receives a signal from your remote
control. Do not block sensor view from remote
control.
10 Display panel
Displays information to assist you in operating
the VCR successfully.
Front panel display
1 POWER
Indicates that the VCR Power is on.
2 RECORD
Indicates that the VCR is recording a program.
3 VCR
Indicates that the VCR is in VCR mode when lit.
When not lit, the VCR is in TV mode.
4 TIMER
Indicates that a timer recording has been
programmed.
*When the power indicator is blinking on the display panel, the VCR
is in the child lock mode.
Overview of the equipment, continued
POWER
RECORD
VCR
TIMER
This section summarizes the buttons, controls, and
terminals that you will use with your VCR.
Front panel
1 POWER
Press to turn the VCR on or off.
2 STOP/EJECT
Press to stop tape movement and to eject a video
cassette.
3 Cassette compartment
Insert a video cassette into this slot.
4 CHANNEL/TRACKING
Press to change the channel (channels stored in
memory only) or to adjust the tracking.
5 REW
Press to rewind a video cassette.
6 PLAY
Press to play a video cassette or press during video
cassette playback to temporarily pause playback
7 FF
Press to fast forward a video cassette.
4
Remote control
1 POWER
Press to turn your VCR on or off.
2 INPUT
Press to select between the VCR tuner and the
Audio/Video Input jacks (auxiliary).
3 0-9
Press to select channels or to make certain
selections when using the menu system.
4 PLAY
Press to play a video cassette.
5 REW
Press to rewind a video cassette.
6 STOP
Press to stop tape movement.
7 REC/OTR
Press to record the program currently airing
on the channel. Press multiple times to process
one-touch-recording (OTR)time options.
8 SPEED
Press to select tape recording speed (SP, or EP)
9 TV/VCR
Press to select the TV or VCR tuner.
10 CM SKIP
Press during playback mode to skip
commercials or program segments.
11 MENU
Press to display the main menu.
12 EJECT
Press to eject a video cassette from the
compartment.
6
Installing the remote control batteries
1 Open the battery compartment on the back of the
remote control.
2 Install two AAA size batteries as shown. Make sure
the “+” and “–” terminals are oriented correctly.
3 Replace the cover.
Using the remote control
Hold the remote control within an angle range of about
30° from either side of the remote sensor. The remote
control range is about 23 feet (7m) from the VCR.
Point the front of the remote control directly at the front
of the VCR.
Overview of the equipment, continued
8
• If your antenna system has two sets of twin
300-ohm leads, purchase a combiner (available at
electronics stores). Place one set of twin leads
underneath the screws on the combiner and tighten
the screws. Do the same with the other set of twin
leads. Press the cable from the combiner onto the
ANT. IN terminal on the back of your VCR.
Connecting your VCR to your TV
1 Connect one end of a coaxial cable to the RF OUT
terminal on the back of the VCR.
2 Connect the other end of the coaxial cable to the
ANT. IN terminal on the back of the TV.
Connecting your VCR,continued
ANT.IN
VCR
VCR
ANT.IN
Loading...