Audiovox VDS102T User Manual
VDS102T
DROP-DOWN
VIDEO MONTOR
ON OFF AUTO
®
Installation Guide
Important Notice
An LCD panel and/or video monitor may be installed in a motor vehicle
and visible to the driver if the LCD panel or video monitor is used for
vehicle information, system control, rear or side observation or navigation.
If the LCD panel or video monitor is used for television reception, video or
DVD play, the LCD panel or video monitor must be installed so that these
features will only function when the vehicle is in “park” or when the
vehicle’s parking brake is applied.
An LCD panel or video monitor used for television reception, video or DVD
play that operates when the vehicle is in gear or when the parking brake
is not applied must be installed to the rear of the driver’s seat where it will
not be visible, directly or indirectly, to the operator of the motor vehicle.
MATERIALS INCLUDED IN THIS PACKAGE:
1) Over Head Docking Station (P/N 136-3955) – (1 pc)
2) Lamp Harness (P/N 112B3110) – (1 pc)
3) 2 Pin Power Wire Harness with choke (P/ N 112B3143) – (1 pc)
4) Hardware Package
Screws (#4) – (8 pcs)
Self Drilling Screws (#8) – (4 pcs)
Nut – (4 pcs)
5) Trim Ring (P/N 102-4111) – (1 pc)
6) PODTVT (P/N 136-3877) – (1 pc)
7) Mounting Bracket (P/N 108-3856) – (1 pc)
8) Remote Control (P/N 136-3956) – (1 pc)
1
ON OFF AUTO
7
2 3
4 5
8
POWER
EJECT
FMM
CHANNEL
SELECT
ON/OFF
SOURCE
1
2
3
AUTO
MEMORY
6
4
5
SKIP/
SEARCH
9
7
8
ERASE/
+
-
WRITE
0
VOLUME
SEEK/CH
PIXMUTE
SEARCH SEARCH
ENTER
MENU
SETUP
RETURN
REPEAT
SEEK/CH
A-B
RADIO TV/CATVTV DVD
DISPLAY BAND RECALL STORE
ZOOMAUDIO
SUBTITLE
ANGLE
PLAY
IIPAUSE
STOP
6
TOOLS REQUIRED:
Nut Driver / Socket Wrench
#2 Phillips Screwdriver
#1 Phillips Screwdriver
Utility or Razor Knife or Shears
Wire Strippers
Upholstery hook tool (for removal of panels as necessary)
Electrical Tape
Masking Tape
Multimeter (to verify 12 volt DC and continuity: Do not use a test light or logic probe)
Marker pen – to mark headliner
Scribe (to mark trim ring if used)
Misc. electrical connectors (to connect to vehicle power source). Requirements will vary
from vehicle to vehicle)
~1~
12
3
1. Infrared Sensor
14
13
12
11
10
4
5
6
7
8
9
– Allows the remote control to operate the VDS102T and to control the shuttle when docked.
2. Three position Dome Light Switch
• Auto – Automatically switches on the dome lights in conjunction with the vehicle’s interior
illumination.
• Off – The dome lights will not turn on in this position.
• On – Turns on the dome lights.
3. Dome Lights –
4. Channel ( ) Button –
5. Channel ( ) Button –
6. Auto Program Button –
7. Screen Release –
8. Shuttle Shut-off Switch –
9. Security Lock Knob –
10. 24 Pin Signal Interface Connector –
11. Shuttle Release –
12. POWER Button –
13. FMM Select Button –
Provide additional interior illumination.
5
Used this button to increase the channel number to the desired number.
6 Used this button to decrease the channel number to the desired number.
Allows the user to scan and store active TV stations into memory.
Moves in the direction of the arrow to release the drop down screen.
Turns off the shuttle when closed.
Used to ensure that the shuttle is not released accidentally.
Used to connect the shuttle to the docking station.
Press to release the shuttle from the docking station.
Used to turn the system ON/OFF. Bright red when system is on, dim when off.
When this button is pressed it will turn on the wireless FM Modulator and
then cycle through the available FM frequencies (FM Off, Channel 1, 88.3MHz; Channel 2, 88.7MHz;
Channel 3, 89.1MHz; Channel 4, 89.5MHz; Channel 5, 89.9MHz).
14. Source Select Button –
Used to select one of the three sources (DVD, AV1, TV)
~2~
Loading...