Audiovox VBP620 User Manual

VBP620

PORTABLE 6.2" LCD MONITOR AND DVD PLAYER

IN A BAG

Notice:

This Product incorporates copyright protection technology that is pro­tected by method claims of certain U.S. Patents and other intellectual
property rights owned by Macrovision Corporation and other rights own­ers. Use of this copyright protection technology must be authorized by
Macrovision Corporation, and is intended for home and other limited view­ing uses only unless otherwise authorized by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.
An LCD panel and/or video monitor may be installed in a motor vehicle
and visible to the driver if the LCD panel or video monitor is used for
vehicle information, system control, rear or side observation or navigation.
If the LCD panel or video monitor is used for television reception, video
or DVD play, the LCD panel or video monitor must be installed so that
these features will only function when the vehicle is in park! or when the
vehicle"s parking brake is applied.
An LCD panel or video monitor used for television reception, video or
DVD play that operates when the vehicle is in gear or when the parking
brake is not applied must be installed to the rear of the driver"s seat
where it will not be visible, directly or indirectly, to the operator of the
motor vehicle.

A. Introduction

Thank you for selecting the VBP620 portable DVD player in a bag.
The main features include a 6.2" Screen (16:9 Aspect Ratio) Liquid
Crystal Display (LCD) monitor and a DVD player. The unit applies
the latest state of the art electronics and is designed for use in hotels,
offices home or vehicle. The unit is constructed to provide years of
reliable, trouble-free service, and is compact so that you can take it
with you anywhere and is designed for quick and easy installation.
Please read the entire instruction manual supplied with this product
prior to operation. The documentation will assist you in installing the
system properly to obtain the best equipment performance. All manu­als should be stored for later use.

B. Cautions and Warnings

1. Placement

To prevent fire or electric shock, do not expose this appliance to
rain or moisture. Do not place the set on an unstable cart, stand,
tripod, bracket or table to prevent it from falling. Keep the unit away
from strong magnets, heat sources, direct sunlight, excessive dust.
If the unit is brought directly from a cold to a warm location, mois­ture may condense inside the unit. When you move it from a cold
to a warm location, wait for about one hour before operating the
unit, or remove the disc and leave the unit turned on until the mois­ture evaporates.

2. Installation

Ensure that the VBP620 is installed in accordance with the in­structions and illustrations provided in this manual.

3. Object and Liquid

Do not push objects of any kind into the unit through openings; do
not spill or spray liquid of any kind on or in the system (this may
result in a fire or electric shock). Do not place anything heavy on
the unit. To ensure proper ventilation and proper operation, never
cover or block the slots and openings with a cloth or other material.

3

4. Disassembly

Do not attempt to disassemble the cabinet. There is a risk of elec­tric shock and/or exposure to Laser Radiation. Contact qualified
service personnel if your system is in need of repair.

5. Cleaning Unit

When cleaning, make sure the system is unplugged from the power
source. Do not use liquid cleaners or aerosol cleaners. Use a
cloth lightly dampened with water for cleaning the exterior of the
system only.

6. Disc

Do not use irregularly shaped discs such as heart or star-shaped
discs as they may cause the unit to malfunction. Do not stick paper,
tape or glue on the disc. Do not expose the disc to direct sunlight
or heat sources such as hot air ducts. Do not touch the surface of
disc. Handle the disc by its edge. Clean the disc by wiping the disc
from the center out with a cleaning cloth. Remove the disc from
the unit and store it in its case after playing. Some playback opera­tions of discs may be intentionally fixed by software producers.
Since this unit plays discs according to the disc contents the soft­ware producers designed, some playback features may not be
available. Also refer to the instructions supplied with the discs.

C. Contents

1. 1 x 6.2"" LCD Monitor & DVD Player Combination

2. 1 x AC to DC Adapter

3. 1 x Remote Control w/Battery (CR2025)

4. 1 x Instruction Manual

5. 1 x Power Adapter w/Built-In FM Modulator

6. 1 x Mounting Bag w/Straps

7. 1 x Carrying bag

8. 1 x Rechargable Battery Pack (Part Number RB05)

9. 1 x Audio/Video Input Cable

10. 1 x Audio/ Video Output Cable

4

OPTIONAL:
Wireless IR headphones (Part Number IRHSCS)

D. Powering and installation

1. Powering the system indoors (Refer to Figure 1)
Plug one end of the AC to DC adapter into the DC 9V jack on the
right side of the main unit, then plug the other end into the 120V AC
power receptacle.

2. Powering the system in a car

Plug one end of the DC Power adapter into the DC 9V jack on
the unit, then plug the other end into the cigarette lighter socket.

Figure 1

3. Powering the system with rechargeable Battery

Please refer to K. * Rechargeable Battery Installation and Use
(Page 34 and 36).

E. Installation Prior to installation

Make sure that the unit is placed into the mounting bag with the clear
plastic covering around DVD door, Load a disc into the DVD
compartment and then fasten the Velcro strap across the top portion
of the unit. If you are installing the bag onto the seatback you will need
to attach the supplied Seat Standoff to the back of the mounting bag
with the Velcro bands to obtain the proper viewing angle as shown in
Figure.2

5

1.Installing the System onto the seat back in a car

(Refer to Figure 2)

Seat Standoff

Figure 2

1).Take one of the supplied straps from the carrier bag. Connect
the latch to one of the upper metal rings on the mounting bag.
Connect the S! hook to the other upper metal ring and place the
loop over the headrest. Adjust the strap until the bag is firmly
secured.

2).Take another strap from the carrier bag, and connect the latch to
the lower metal ring on the left side of the bag. Attach the S!
hook to the same ring after looping the strap around the seat rail.
Repeat this process for the right side. In some vehicles, it may
be necessary to attach the S! connector to the rail directly, as it
may not be long enough to reach back to the ring.

3).Adjust the straps tightly so that the bag is secured.

6

2. Installing the system between the driver/passenger seat

(Refer to Figure 3)

Figure 3

1). Take one strap and connect the latch to the upper metal ring on
the left side of the bag. Attach the S! hook to the same ring
after looping the strap around the headrest of the driver"s seat.
Repeat this process for the right side (Passenger Seat).

2).Take another strap and connect the latch to lower metal ring on
the left side of the bag. Attach the S! hook to the same ring
after looping the strap around the driver"s seat rail. Repeat this
process for the right side. In some vehicles, it may be neces­sary to attach the S! connector directly to the rail, as it may not
be long enough to reach back to the ring.

3).Adjust the straps tightly so that the bag is secured.

7

F. Controls, Indicators, and Connectors

1. Unit View (Refer to Figure 4)

Figure 4

1) Screen Mode Button

2) Pause Button

3) Play Button

4) Open Button

5) Previous Button

6) Stop Button

7) Next Button

8) IR Transmitter

9) Remote Control Sensor

10) Power LED

11) Power On/Off Switch

12) Brightness control

13) Volume control

14) Headphone Jack 1

15) Headphone Jack 2

16) IR On/Off Switch

17) DC 9V Input Jack

18) DVD Video Output Jack

19) DVD L+R Audio Output
Jack

20) Video Input Jack

21) Audio L+R Input Jack

8

2. Remote Control View (Refer to Figure 5)

1) DISPLAY Button

2) ANGLE Button

3) SUBTITLE Button

4) AUDIO Button

5) ZOOM Button

6) UP/DOWN/LEFT/RIGHT/

ENTER Button

7) RETURN Button

8) A-B Button

9) FORWARD Button

10) REVERSE Button

11) SLOW Button

12) STOP Button

13) NUMERIC KEYPAD

14) SETUP Button

15) MENU Button

16) REPEAT Button

17) PREVIOUS Button

18) NEXT Button

19) PLAY Button Figure 5

20) PAUSE Button

9

G. Loading and Playing a Disc

a. After connecting power to the unit, slide the POWER ON/OFF on

the right side to ON, the DVD player"s POWER indicator lights.

b. Open the disc tray by pressing OPEN at the lower right of the disc

tray, and place a disc into the tray with the disc"s label facing up.

c. Press at the right side of the door until it clicks shut. The unit will

load the disc and start playing.

d. Rotate BRIGHT and VOLUME to adjust the LCD"s brightness and

the DVD player"s volume.
e. To stop playing a disc, press STOP.
f. To turn off the DVD player, slide POWER ON/OFF to OFF. The

DVD player"s POWER indicator turns off.
g. To remove the disc, open the disc tray, just use your finger to

access the right inner corner of the disc tray and lift up the disc

and remove it from the disc tray. Please refer to Figure 6.

Figure 6

10

H. SETUP

Press #SETUP" to display the Main screen of the SETUP Menu on
the screen. Press #SETUP" again to exit the SETUP Menu and the
unit will resume its last playback mode.

1) Press #SETUP", the General Setup Page! will display on screen.

General SETUP Menu Screen

a).Select #TV Type" using UP/DOWN, and then press the RIGHT

button to enter the submenu. Choose TV Type using UP/DOWN
and then press ENTER to confirm the setting. Press the LEFT
button to return.

TV Type Screen Display

b).Select #TV Display" using the UP/DOWN button, and then press

RIGHT to enter the submenu. Select the TV display mode on
the screen using UP/DOWN, and press ENTER to confirm the
setting. Press LEFT to return.

11

TV Display Screen Display

* Normal/PS: When the player is connected to a normal TV, and a

wide picture is shown on the full screen.

* Normal/LB: When the player is connected to a normal TV, and a

wide picture is shown on the screen with a black strip at both the
top and bottom of the screen.

* Wide: When the player is connected to a wide screen TV, a wide

picture is shown on the full screen.

c).Select #Angle Mark" using the UP/DOWN buttton, and then press the

RIGHT button to enter the submenu. Choose Angle Mark on or off
using the UP/DOWN button and then press ENTER to confirm the
setting. Press the LEFT button to return.

Angle Mark Screen Display

* On: The screen will show the angle mark icon. (*If an angle option

is available).
* Off: The screen will not display the Angle Mark icon.
NOTE: Not all discs contain above features.

12