Applicant: Shintom Co., Ltd. Transmitter Type: BFYT3017
EXHIBIT 20
PAGE 1 OF 52
1
Important
There are some basic rules that apply to most hardware installation procedures
and need to be observed to prevent damage or injury.
1. Always make sure that any power is disconnected to the vehicle before handling any
electrical components like wiring, fuseboxes, connectors, etc.
2. Never force any connection between components, electrical connectors or the like.
3. Always use the proper tools for the task at hand. Using improper tools may cause
damage to yourself, your vehicle, or your cellular telephone system.
4. Think through all the necessary steps of installation before actually beginning the
procedure and equip yourself for all steps to be performed.
5. Always make sure your workspace and your tools are clean and tidy. The
introduction of dirt or grease may hinder the performance of your cellular telephone
and related components.
Installation Procedure
1. Before we begin
You will need the following items in order to properly install the cellular telephone in the
trunk of an automobile.
1. Cradle (CR91)
2. Mounting Bracket (MT91)
3. Power Cable (EPC91)
4. Extension Cable (EIC91)
5. Clamshell Bracket
6. Screw kit
(M4 × 6) (SKM46)
(M4 × 10) (SKM410)
(M4 × 35) (SKM435)
7. Hands-Free Microphone (MIC91)
8. Installation Guide (OMCMK**)
Applicant: Shintom Co., Ltd. Transmitter Type: BFYT3017
EXHIBIT 20
PAGE 2 OF 52
2
2. Mount the Transceiver unit
To install the cellular telephone with the transceiver unit located in the trunk-space of the
automobile follow the steps outlined below.
a. Place the mounting bracket so that the
four bracket holes line up with the transceiver holes.
b. Replace the four screws (supplied M4 ×
6mm) in the screw kit so that the mounting bracket is secured to the transceiver
unit.
c. Place the unit top-side up (bracket feet
down), utilizing the included flatwashers,
insert the four self-tapping screws (supplied M4 × 35mm) and tighten them
down.
Orange
Extension Cable
Power Cable
fuse 3A
fuse 1A
Red
Black
3. Wiring
a. Connect the cables to the mounted transceiver unit using the supplied trunk mount
extension cable as illustrated.
Car Battery
Ground (Black)
Back up (Red)
Ignition (Orange)
Extension cord
Hands-Free Mic
Cradle
Hand Set
Transceiver unit
Antenna
Applicant: Shintom Co., Ltd. Transmitter Type: BFYT3017
EXHIBIT 20
PAGE 3 OF 52
3
4. Mount the Cradle and Handset
a. Using a pedestal mount. The cradle unit
can be mounted as displayed. Be sure
to use only supplied M4 × 10mm screws.
Using improper screws will damage the
cradle unit.
b. Plug in the handset and Hands-Free
Mic.
c. Check to make sure ALL signal and
power leads are in place and properly
connected.
Hands-Free Mic
Applicant: Shintom Co., Ltd. Transmitter Type: BFYT3017
EXHIBIT 20
PAGE 4 OF 52
4
5. Antenna
The following is the standard antenna installation for TR93.
Antenna type : Glass mount type - Colinear
Mount location : Rear window of a vehicle
Antenna cable : RG-58/U 8 feet (2.44m) or longer
Install the antenna on your vehicle as shown below.
Rear window
Transceiver unit
Antenna
Coaxial cable
RG-58/U
8 feet or longer
Rear window
Antenna
Applicant: Shintom Co., Ltd. Transmitter Type: BFYT3017
EXHIBIT 20
PAGE 5 OF 52
TR93
MOBILE CELLULAR TELEPHONE
OPERATING INSTRUCTIONS
PRINTED IN XXXX x-xx
288Exxxx
555 Wireless Blvd., HAUPPAUGE, NY 11788
Applicant: Shintom Co., Ltd. Transmitter Type: BFYT3017
EXHIBIT 20
PAGE 6 OF 52
TELEPHONE
Congratulations. By choosing the TR93, you have joined the
millions of satisfied customers who are enjoying the benefits
and quality performance that only an Audiovox Cellular Tel-
ephone can provide.
Your Audiovox Mobile Cellular Telephone has been designed
to the highest standards of quality and manufacturing excellence to fulfill both your personal and business requirements.
The Audiovox TR93 is packed with advanced features like
Programmable One Touch Emergency Dialing, Anti-Fraud Security Features, Automatic Call Retry, a Constant Signal
Strength Indicator.
And of course, your new Audiovox TR93 comes with something
only an Audiovox phone can provide The proven reliability
that has made Audiovox one of the world's leading suppliers
of cellular communications equipment.
The following pages describe your phone's functions and will
help you make the most efficient use of this wonderful communications tool.
Following codes can be obtained through your
selling Audiovox dealer.
a. 3-digit Initial Lock (Unlock) Code
b. 3-digit Initial Call Restriction Code
c. 2-digit Initial Call Counter Code
d. 2-digit Initial Call Timer Code
Keep these codes in a safe place!
TR93 MOBILE CELLULAR
Applicant: Shintom Co., Ltd. Transmitter Type: BFYT3017
EXHIBIT 20
PAGE 7 OF 52
1
TABLE OF CONTENTS
INTRODUCTION .............................................. 3
Safety Information for Wireless Handheld Phones ................3
Features ..................................................................................7
Key/Display Names and Functions ........................................8
INSTALLATION .............................................. 10
Cautions ................................................................................10
Parts List ...............................................................................11
BASIC OPERATION....................................... 13
Turning the Phone ON and OFF...........................................13
Display Own Telephone Number .....................................13
Display Own System ID ...................................................13
Placing Calls .........................................................................13
Call-in Progress Protection ...............................................14
Receiving Calls.....................................................................14
Call in Absence Indication................................................14
Silent Incoming Calls .......................................................14
Automatic Answering .......................................................15
Redialing Functions..............................................................15
Last Three Numbers Dialed..............................................15
Automatic Redial (Programmable Option).......................16
MIC Mute During Conversation ..........................................16
Volume Adjustment..............................................................16
Earpiece Volume ...............................................................16
Alert Volume.....................................................................16
Keypad Tone Volume........................................................16
ENHANCED OPERATION ............................ 17
Locking/Unlocking the Phone ..............................................17
Locking the Phone ............................................................17
Changing the Unlock Code...............................................17
Automatic Lock (Programmable Option).............................17
Keypad Disable Function in Handsfree Mode
(Programmable Option)........................................................18
Storing in the Memory .........................................................19
Name Entry Keys..............................................................19
Manual Storage .................................................................20
Automatic Storage ............................................................22
Storage After Vacant Memory Location Search ...............22
Editing the Telephone Numbers and Names ........................ 23
Editing the Telephone Numbers .......................................23
Editing the Names ............................................................24
Editing Phone Number under Stored Name .....................24
Memory Search.................................................................24
Applicant: Shintom Co., Ltd. Transmitter Type: BFYT3017
EXHIBIT 20
PAGE 8 OF 52
2
Recalling Numbers from Memory........................................24
Memory Dialing ...............................................................24
Dialing after Telephone Number Search ..........................25
Dialing after Name Search................................................25
Speed Dialing ...................................................................25
Link Dialing .........................................................................26
Storing Number in Link Dialing Memory ........................ 26
Recalling Number from Link Dialing Memory................26
Making Link Dialing ........................................................26
One Touch Dialing................................................................27
Storing in the One Touch Memory ...................................27
Placing a Call with One Touch Memory ..........................27
Programmable One Touch Emergency Call .........................27
Placing One Touch Emergency Call .................................27
One Touch Emergency Call ON/OFF...............................27
Programming a New Emergency Number........................27
Scratch Pad Memory ............................................................28
Storing Numbers in the Scratch Pad Memory ..................28
Dialing Numbers in the Scratch Pad Memory ..................28
Emergency and Priority Dialing ...........................................28
Storing the Emergency and Priority Number ................... 28
Dialing the Emergency and Priority Number ...................28
EXTENDED FEATURES AND FUNCTIONS .......
29
Call Restriction .....................................................................29
To Activate the Call Restriction ........................................29
To Change the Call Restriction Code ...............................29
Keypad (DTMF) Tones.........................................................30
Keypad (DTMF) Tones Duration Selection ......................30
Keypad (DTMF) Tones Mute during conversation...........30
Sending DTMF Tones During a Call ................................30
Timer and Counter Functions ...............................................30
Elapsed Time Display .......................................................30
Outgoing Call Timer.........................................................31
Cumulative Call Timer...................................................... 31
Temporary Accumulated Call Counter ............................. 31
Outgoing Call Counter......................................................32
Accumulated Call Counter ...............................................32
To Change the Call Timer/Call Counter Codes ................ 32
Call Time Warning Tone ...................................................33
SID Management (Programmable Option) ..........................33
A/B System Selection...........................................................33
Multiple City Registration ....................................................34
Current SID, Channel and RSSI Level Display ...................35
Electronic Serial Number (ESN) ..........................................35
Anti Fraud Security Feature (PIN Feature) ..........................35
Function Review...................................................................36
GENERAL SPECIFICATIONS ..................... 41
TABLE OF KEY OPERATION...................... 42
12 MONTH LIMITED WARRANTY ............ 45
Applicant: Shintom Co., Ltd. Transmitter Type: BFYT3017
EXHIBIT 20
PAGE 9 OF 52
3
INTRODUCTION
SAFETY INFORMATION FOR MOBILE
PHONES
IMPORTANT
READ THIS INFORMATION BEFORE USING
YOUR MOBILE CELLULAR TELEPHONE
The cellular telephone is one of the most exciting and innovative electronic products ever developed. With it you can
stay in contact with your office, your home, emergency services, and others.
For the safe and efficient operation of your phone,
observe these guidelines.
Your mobile cellular telephone is a radio transmitter and receiver. When the phone is ON, the antenna is the part of the
phone that sends out and receives radio frequency (RF) energy . The phone operates in the frequenc y range of 824 MHZ
to 894 MHZ and employs commonly used frequency modulation (FM) techniques. When you use your phone, the cellular system handling your call controls the power level at
which your phone transmits. The power le vel can range from
0.006 of a watt to 3 watts.
EXPOSURE TO RADIO FREQUENCY ENERGY
In 1991 the Institute of Electrical and Electronics Engineers
(IEEE), and in 1992 the American National Standards Institute (ANSI) updated the 1982 ANSI Standard for safety levels with respect to human exposure to RF energy. Over 120
scientists, engineers, and physicians from universities, government health agencies, and industry, after reviewing the
available body of research, de veloped this updated Standard.
In March, 1993, the U.S. Federal Communications Commission (FCC) proposed the adoption of this updated Standard.
To operate within this updated ANSI Standard, use your
phone as described under “Efficient Phone Operation.”
EFFICIENT PHONE OPERATION
Do not operate your mobile cellular telephone when holding the
antenna, or when any person is within 4 inches (10 centimeters)
of the antenna.
A person or object within 4 inches (10 centimeters) of the antenna could impair call quality , cause your phone to operate at a
Applicant: Shintom Co., Ltd. Transmitter Type: BFYT3017
PAGE 10 OF 52
EXHIBIT 20
4
higher power level than necessary, and expose that person to RF
energy in excess of that established by the updated ANSI Standard.
For best call quality, keep the antenna free from obstructions
and point it straight up.
If you want to limit RF exposure even further than the updated
ANSI Standard, maintain a distance from the antenna of more
than 4 inches (10 centimeters). Of course, you may also choose
to control the duration of your calls.
ANTENNA CARE AND REPLACEMENT
Do not use the phone with a damaged antenna. If a damaged
antenna comes into contact with the skin, a minor burn may result. Replace a damaged antenna immediately. Consult your
manual to see if you may change the antenna yourself. If so, use
only a manufacturer approved antenna. Otherwise, have your
antenna repaired by a qualified technician.
Use only the supplied or an approved antenna. Non-approved
antennas, modifications, or attachments could impair call quality, damage the phone, and violate FCC regulations.
DRIVING
Check the laws and regulations on the use of cellular telephones in the areas where you drive. Always obey them. Also,
when using your phone while driving, please:
• give full attention to driving,
• use hands-free operation, if available, and
• pull off the road and park before making or answering a
call if driving conditions so require.
ELECTRONIC DEVICES
Most modern electronic equipment is shielded from RF energy. However, RF energy from cellular telephones may affect inadequately shielded electronic equipment.
RF energy may affect improperly installed or inadequately
shielded electronic operating and entertainment systems in
motor vehicles. Check with the manufacturer or its representative to determine if these systems are adequately
shielded from external RF energy. You should also check
with the manufacturer of any equipment that has been added
to your vehicle.
Consult the manufacturer of any personal medical devices
(such as pacemakers, hearing aids, etc.) to determine if they
are adequately shielded from external RF energy.
Applicant: Shintom Co., Ltd. Transmitter Type: BFYT3017
PAGE 11 OF 52
EXHIBIT 20
5
Turn your phone OFF in health care facilities when an y re gulations posted in the areas instruct you to do so. Hospitals
or health care facilities may be using equipment that could
be sensitive to external RF energy.
AIRCRAFT
Turn your phone OFF before boarding any aircraft.
• Use it on the ground only with crew permission.
• Do not use it in the air.
To prevent possible interference with aircraft systems, U.S.
Federal Aviation Administration (FAA) regulations require
you to have permission from a crew member to use your
phone while the plane is on the ground. To prevent interference with cellular systems, FCC regulations prohibit using
your phone while the plane is in the air.
CHILDREN
Do not allow children to play with your phone. It is not a
toy. Children could hurt themselves or others (by poking
themselves or others in the eye with the antenna for example).
Children also could damage the phone, or make calls that
increase your telephone bills.
BLASTING AREAS
To avoid interfering with blasting operations, turn your unit
OFF when in a “blasting area” or in areas posted: “Turn off
two-way radio”. Construction crews often use remote control RF devices to set off explosives.
POTENTIALLY EXPLOSIVE ATMOSPHERES
Turn your phone OFF when in any area with a potentially
explosive atmosphere. It is rare, but your phone or its accessories could generate sparks. Sparks in such areas could
cause an explosion or fire resulting in bodily injury or even
death.
Areas with a potentially explosive atmosphere are often, but
not always, clearly marked. They include fueling areas such
as gas stations; below deck on boats; fuel or chemical transfer or storage facilities; areas where the air contains chemicals or particles, such as grain, dust, or metal powders; and
any other area where you would normally be advised to turn
off your vehicle engine.
Do not transport or store flammable gas, liquid, or explosives in the compartment of your vehicle which contains your
phone or accessories.
Applicant: Shintom Co., Ltd. Transmitter Type: BFYT3017
PAGE 12 OF 52
EXHIBIT 20
6
Vehicles using liquefied petroleum gas (such as propane or
butane) must comply with the National Fire Protection Standard (NFPA-58). For a copy of this standard, contact the
National Fire Protection Association, One Batterymarch
Park, Quincy, MA 02269, Attn.: Publications Sales Division.
Applicant: Shintom Co., Ltd. Transmitter Type: BFYT3017
EXHIBIT 20
PAGE 13 OF 52
7
FEATURES
• SID management (programmable option)
• Multiple city registration
• Easy to read LCD display with alphanumeric and status indi-
cators
• Back-lit keypad and LCD display
• Microphone mute control
• Priority/emergency calling with automatic retry
• 9 number speed dialing
• Automatic redial (programmable option)
• 89 alphanumeric memory locations
• 7 location scratch pad, with automatic scroll
• Vacant memory location search
• Automatic entry into vacant memory location
• Phone number search
• Name search
• Programmable one touch dialing
• Programmable one touch emergency call
• Last 3 number dialed memory
• Silent incoming calls
• Automatic answering
• Call in progress protection
• Call time warning tone
• DTMF tone dialing from memory
• DTMF keypad mute
• DTMF extended tone dialing
• A/B system selection
• Current SID, RF channel and RSSI level display
• Automatic self diagnostics
• Electronic serial number display (own)
• Telephone number display (own)
• System ID display (own)
• 6 function call timer
• Function review
• Anti-Fraud PIN feature capability
• Automatic lock (programmable option)
• Keypad disable in handsfree mode (programmable option)
• Link dialing
This cellular telephone is also capable of supporting the following optional network services.
1) Caller ID
2) Voice Mail Notification
3) Short messaging Service
Note: Your cellular service provider may use different
terminology when referring to the enhanced features listed above. Please check with your cellular
service provider for an explanation and availability of these enhanced features.
Applicant: Shintom Co., Ltd. Transmitter Type: BFYT3017
EXHIBIT 20
PAGE 14 OF 52
8
KEY/DISPLAY NAMES AND FUNCTIONS
Loudspeaker
Curly Cord Socket
IN USE Indicator4
Mute Indicator5
Send Key A
System A Indicator1
System B Indicator2
62-digit Display
Received Signal
Strength Indicator
8 Function Mode
Indicator
7ROAM Indicator
0Message Indicator
3
B End Key
Power Key C
Digit Keys E
Programmable D
One Touch
Emergency Key
K Message Review
Key
914-digit Display
Up/Down Keys F
H Clear Key
I Function Key
J Recall/Store Key
G
One Touch Dial,
Mute, and Alpha Key
Applicant: Shintom Co., Ltd. Transmitter Type: BFYT3017
PAGE 15 OF 52
EXHIBIT 20
9
1 A lights when the system A (non-wireline) is selected.
2 B lights when the system B (wireline) is selected.
Note: AB lights when standard mode is selected.
3 Received Signal Strength Indicator Yi constantly
displays the signal strength represented by the number
of bars.
4 I lights when a call is in progress.
5 M lights when the mute control is in effect.
6 2-digit display 8.8shows the memory location number
and the status of various functions.
7 R lights when receiving services other than a regis-
tered home system.
8 F lights when f is pressed to select extended func-
tions, etc.
9 14-digit display shows the telephone number dialed, etc.
0 a flashes when Message is received where En-
hanced Feature Service is provided.
A sinitiates and answers a call.
B eterminates a call.
C p(Power) turns your phone on and off.
D 1 (Programmable One Touch Emergency Key) places
a call to the programmed emergency number by a single
key stroke.
E Digit keys enter telephone numbers, alphanumeric in-
formation, etc.
F Up/Down keys ^ and v adjusts the alert, earpiece and
keypad tones. ^ and v are also used to select
ON/OFF setting and scroll.
G
M/A
(One Touch Dial, Mute and Alpha Key):
• In standby mode, the stored telephone number in the
one touch memory is dialed with a single key stroke.
• During conversation, switches off the microphone to
mute your voice.
• Used to enter alphanumeric characters.
H c (Clear) clears the digit(s) from the display.
I f (Function) is used with digit keys to allow operation
of extended functions, etc.
J
R/S
(Recall/Store) recalls telephone numbers from the
memory. Also used to store telephone numbers in the
memory.
K
(Message) enters Message Review Mode.
Applicant: Shintom Co., Ltd. Transmitter Type: BFYT3017
EXHIBIT 20
PAGE 16 OF 52
Loading...