Audiovox PRO-PDL-2B, PRO-PDL-4B Installation Instructions Manual

I. PREPARING FOR INSTALLATION:

1. Review installation drawings and wiring diagram to familiarize yourself with the use
and wiring of the system.
NOTE: These instnx:tions apply to both the 2-Door and 4-Door Lock systems.
If installing the 2-Door system, ignore the section applicabie to the 4-Door system.

2. Determine where the CONTROL MODULE will be mounted. This will normally be
behind the dash near the fuse block to allow for connection of the 12 Volt Positive
and Ground Wires.

3. Examine the WIRING HARNESS. You will find two groups of 5 wires each (on 4-door
models you will also find two groups of 2 wires each). One of the 5-wire harnesses

will be shorter than the other. This short harness is to be routed to the front door
nearest the mounting location of the CONTROL MODULE.

4. Remove door panels on all doors.

II. CONTROL MODULE MOUNTING & WIRE ROUTING:

1. Select mounting location for CONTROL MODULE and secure with two self-tap 4 X

12 mm screws.

2. Plug wiring harness into control module.

3. Route the SHORT 5-wire harness to the FRONT door nearest the CONTROL
MODULE by the folk)wing method:

a) If the door has an existing rubber tube connecting the door jamb to the door. route

the wires through the tube and into the door.

b) If the door has no existing tube, drill a 3/8. diameter hole in the door jamb and in

the door. Route wires out the hole in the door jamb and into the flexible rubber
tube provided. Route wires into the hole in the door. Allow enough slack in wires
for door to open completely and press grommets on ends of the tube into the
drilled holes.

4. Now route the long S-wire harness to the other FRONT door in the sarne manner.

5. If installing the 4-door kit, route one 2-wire harness into each REAR door in the same
manner as for the front doors.

6. Do not connect any wires at this time.

Form No. 12&-42~

128-4230A

III. POWER LOCK MECHANISM MOUNTING:

1. Refer to mounting illustration for POWER LOCK MECHANISM.

2. Select mounting location insKje door that will not interfere with WINDOW.
WINDOW MOVEMENT, DOOR MECHANISM or any other part within the door.

3. Make certain thls location will enable connection of the POWER LOCK
MECHANISM to the existing door lock button mechanism as shown.

4. Once selected, use one of the two possible mounting methods shown (direct
mounting to door frame method or use of mounting support strap method).

5. Once the mounting method Is decided on, install the POWER LOCK MECHA­NISMS in each door using the hardware shown in the applicable drawing.

NOTE: Use 5-wire locks in front doors and 2-wire locks in rear doors.

IV. CONNECTION OF POWER DOOR LOCK MECHANISM TO DOOR

LOCK:

1. Refer to drawings for the possible connection methods depending on type of
existing door lock and the location of the existing door button rod that joins the
button to the door lock.

2. Assemble as follows:
a) Place CONNECTING ROD threw the hole in the POWER LOCK MECHA-

NISM plunger as shown.

b) Bend CONNECTING ROD as necessary to reach the existing door button

rod.

c) Place the CONNECTING ROD ADAPTOR over the existing door button

rod as shown and secure by inserting the 4 x 11 mm hex head screw into
the threaded hole and tightening firmly .

d) Manually move the existing door lock button tram the locked to the

unlocked position and check that the attached mechanism moves smoothly
and the plunger on the POWER LOCK MECHANISM extends and

retracts.
e) Tighten any loose screws.
f) Repeat procedure tor all remaining doors.

CONNECTION METHODS:

UNLOCK I I

REAR DOOR

LOCK

Ji

LOCK ~ ~ UNLOCK

~

I

c

128-4230J