Audiovox PRO-9649B User Manual

Page 1

Model: PRO-9649b

Owner’s Manual

3 Button Remote Security System

with Dual Stage Shock Sensor

IMPORTANT ! In order to provide the highest possible level of security to your vehicle, this system is equipped with selectable manual override circuitry . It is possible that you will need to manually override your security system if the transmitter becomes lost, or inoperative due to battery failure. Reading the sections on "MANUALLY OVERRIDING YOUR SYSTEM" is nec- essary to fully understand the procedure required to enable your vehicle in such situations. In addition, the chart on the last page of this manual has a section for the particular features and options installed in your vehicle as well as the override method selected. Valet Switch manual override is pre-selected from the factory, however, the system can be configured for "Custom Code" operation. Confirm the override mode selected on the last page of this manual, and familiarize yourself with the selection on it's operation.

FEATURES:

 2 Three Button Programmable RF Trans-

mitters

 Five Channel Receiver

(capable of accepting 4 transmitters)

 Code Hopping Technology  Selectable Manual Override Mode  Remote Panic in all modes  Protected Valet  User Programmable Manual Override

Code

 7 Function LED - Arm / Disarm / Zone 1

/ Zone 2 / Zone 3 / Valet / Arming

 Intrusion Alert with Memory  Audible Arm / Disarm / Defective Zone /

T amper Confirmation

 Instant Siren Activation  Starter Disable  True Last Door Arming (hardwire only)  Defective Zone By-Pass  Hardwire or Voltage Sense Selectable  Active or Passive Arming Selectable

OPTIONS:

 Remote Trunk Release (must have electronic trunk release)  Remote Keyless Entry (must have power door locks)  Multiple Vehicle Capable  Remote Starter  Remote Power Window Roll Up  Remote Garage Door Interface  Headlight Illumination During Arming/Disarming, Or Both

 Programmable Auto Lock On / Off  Programmable Auto Unlock On / Off  Programmable Door Lock Pulse Duration 1

Second/3.5 Seconds/1 Sec L/Dbl. U/L

 Programmable Active or Passive Door

Locks

 User Programmable Permanent Chirp Delete  On Command RF Chirp Delete from Trans-

mitter Or Selectable Through Software

 6 Tone Multi Tone Siren (And or)  Car Horn Activation for additional alarm

response

 Additional Negative Trigger Input  RF Inhibit with ignition on  Parking Light Flasher  Remote Trunk Release (must have

electronic trunk release)

 Remote Keyless Entry With Optional

Access Guard (must have power door locks)

 Illuminated Entry  Plug In Dual Stage Shock Sensor

128-8190

1 of 8

Page 2

YOUR "Code Hopping" TRANSMITTERS

The transmitters included with your new security system use the most advanced and secure form of radio frequency transmission available on any current automotive security system. Some of today’s sophisticated auto thieves use a device known as a code grabber, which will receive and store the signal from your keychain transmitter, and re transmit at a later time to disarm your system.

Your code hopping transmitters will change their signal every time the button is pressed, so when a thief grabs then retransmits your signal, the alarm system will not respond.

If your transmitter button is pressed more than fifty times while it is out of range of the vehicle (children playing with your keys), the transmitter will not operate when you return to the vehicle, and will need to be realigned to the receiver. To do this, simply press the lock button two times within a one second time period. The system will now respond to that transmitter each time a button is pressed.

Note: Your system has the option of using a siren, the vehicle horn, or both for the

ARMING THE SYSTEM - ACTIVE

1. Turn off the engine, exit the vehicle, and close all doors, hood lid, and trunk lid.

2. Press and release the Lock button on the keychain transmitter.

SILENT ARMING - ACTIVE

1. Turn off the engine, exit the vehicle, and close all doors, hood lid, and trunk lid.

2. Press and hold the Lock button on the keychain transmitter for 2 seconds.

ARMING THE SYSTEM - PASSIVE ( AUTOMATIC )

1. Turn off the engine, exit the vehicle, close and lock all doors, hood lid and trunk lid.

2. Opening any protected entry point during the 30 second passive arming cycle will imme-

sounding device. Where the siren is referenced below, the horn or both may in fact chirp, or beep.

; Red dash mounted LED begins to flash slowly. ; Parking Lights flash one time. ; Siren and or Horn sounds one chirp.

If the siren/horn sounds 3 chirps, then you have left a door, trunk, or hood lid ajar. Simply close the opened entry point to provide full protection. If the siren "chirped" three times, sometime after arming, the exclusive delayed dome light learn circuit has been programmed and the system detected a open entry point after the learned delay expired. Again, closing the hood, trunk, or doors will correct the problem and you do not need to disarm the system to make the correction. If the siren/horn did not sound when arming, then the chirps have been turned off, and you should refer to the section titled “ ELIMINATING THE ARM / DISARM CHIRPS “ in this manual.

 Doors Lock - Optional  Headlight Illumination - Optional

; Red dash mounted LED begins to flash slowly. ; Parking Lights flash one time. ; Siren will not sound.

 Doors Lock - Optional  Headlight Illumination - Optional

; Red dash mounted LED begins to flash rapidly, indicating 30 second passive

diately suspend automatic arming, and the 30 second passive arming cycle will restart when all doors are closed. At the end of the passive arming cycle;

If the siren sounds 3 chirps, then you have left a door, trunk, or hood lid ajar. Simply close the opened entry point to provide full protection.

arming has begun.

Page 2

128-8190

2 of 8

Page 3

; Red dash mounted LED begins to flash slowly. ; Parking Lights flash one time. ; Siren sounds one chirp

been turned off and you should refer to the section titled “ELIMINATING THE ARM / DISARM CHIRPS “ in this manual.

 Doors Lock - Optional Door locking during passive arming is a selectable feature. The

alarm can be programmed to allow the doors to lock only when arming using the keychain transmitter, and they will not

PROTECTION WHILE THE SYSTEM IS ARMED

DISARMING THE SYSTEM

1. As you approach the vehicle, press and release the Unlock button on the keychain transmit-

Note: If the optional 2 step door unlock circuit is installed, when the unlock transmitter

automatically lock during passive arming.

; Opening any protected door, hood, or trunk lid will cause the alarm to

; Whenever the system is armed, the red dash mounted LED indicator will slowly

; Whenever the system is triggered, the vehicle’s parking lights will flash for the  Optional - Whenever the system is armed, the vehicle’s starting circuit will be

; Any mild impact to the vehicle’s glass will cause the alarm to sound a short ; Any strong impact to the vehicle’s glass will cause the alarm to trigger for the full

ter.

; Red dash mounted LED turns off.

If passive arming was selected during the installation, then the LED will start flashing rapidly, indicating that the system is re-arming automatically. Open any door to suspend the automatic arming.

; Parking Lights flash two times.

; Siren sounds two chirps.

 Doors Unlock - Optional

button is activated, the drivers door only will unlock, pressing the unlock button a second time will cause all doors to unlock. If your transmitter has a sperate lock

If the siren did not sound when arming, then the chirps have

immediately sound. The alarm will continue to sound for 30 seconds, then stop and continue to monitor all protected entry points. If the thief left a door opened, the alarm will sound for six 30 second cycles, remain armed and ignore that triggered zone.

flash. This serves as a visual deterrent to the potential thief. The LED is a very low current bulb, and will not cause the vehicle’s battery to drain, even when left unattended for extended periods.

full 30 second alarm cycle, attracting visual attention to the vehicle. bypassed. If the thief should choose to ignore the siren, the vehicle can not be

started. series of warning tones. 30 second alarm cycle.

If the parking lights flashed three times, then the alarm was triggered in your absence. Before turning the key on, examine the LED to identify which zone was triggered.

If the siren sounds 4 chirps, then the alarm was triggered in your absence. Before turning the key on, examine the LED and refer to the INTRUSION WARNING SIGNALS section of this manual to identify which zone was triggered.

If the siren did not sound when disarming, then the chirps have been turned off, and you should refer to the section titled " ELIMINATING THE ARM / DISARM CHIRPS " in this manual.

Page 3

128-8190

3 of 8

Page 4

unlock buttons, pressing the unlock button anytime after the first unlock command will cause all the vehicle doors to unlock.

 Headlight Illumination - Optional

SILENT DISARMING

1. As you approach the vehicle, press and hold the Unlock button on the keychain transmitter for 2 seconds.

; Red dash mounted LED turns off.

; Parking Lights flash two times.

; Siren will not sound.

 Doors Unlock - Optional

Note: If the optional 2 step door unlock circuit is installed, when the unlock transmitter

 Headlight Illumination - Optional

WHILE THE SYSTEM IS SOUNDING

If during a triggered state, you wish to shut off the siren without disarming your security system, simply press and release any transmitter button other than the disarm button. This action will turn off the siren yet leave the vehicle fully armed and protected. This feature is particularly useful if you are aware of children playing near your vehicle that may accidently trigger your security system. In this case you can cancel the siren sounding without disarming your alarm.

INTRUSION WARNING SIGNALS

This system will inform you if an intrusion attempt has occurred while you were away from the vehicle. If an intrusion attempt has occurred, the siren will chirp 4 times and the parking lights will flash 3 times when disarming the system. Enter the vehicle, and observe the red dash mounted LED to identify which zone was triggered.

n If the LED is flashing one time...pause...one time...pause...etc., then an intrusion

attempt was made to the shock sensor, or an accessory triggering device that may have been added to the system.

o If the LED is flashing two times...pause...two times...pause...etc., then an intrusion

attempt was made to a hood or trunk pin switch that was added to the system, or to a light activated entry point if the alarm was installed using the voltage sensing feature.

p If the LED is flashing three times...pause...three times...pause...etc., then an intru-

sion attempt was made through one of the vehicle’s doors.

These intrusion warning indicators are stored in the system’s memory and will only be erased when the ignition key is turned on.

PUSHBUTTON LED/V ALET/OVERRIDE/PROGRAMMING SWITCH: (PBLED)

The PBLED switch allows you to temporarily bypass all alarm functions, eliminating the need to hand your transmitter to parking attendants or garage mechanics. When the system is in valet mode, all alarm functions are bypassed, however the remote panic feature and remote

If passive arming was selected during the installation, then the LED will start flashing rapidly, indicating that the system is re arming automatically. Open any door to suspend the automatic arming.

If the parking lights flashed three times, then the alarm was triggered in your absence. Before turning the key on, examine the LED to identify which zone was triggered.

button is activated, the drivers door only will unlock, pressing the unlock button a second time will cause all doors to unlock. If your transmitter has a separate lock/ unlock buttons, pressing the unlock button anytime after the first unlock command will cause all the vehicle doors to unlock.

Page 4

128-8190

4 of 8

Page 5

door locks will remain operational. To use the valet mode, the system must first be disarmed either by using your keychain transmitter, or by activating your personalized manual override code.

1. Enter the vehicle, and turn the ignition key to the on position.

2. Press and hold the PBLED switch until the LED turns on solid. The system will remain in the valet mode.

3. T o return to normal operation, press and release the PBLED switch any time the ignition is on.

Note: Always remember to return the vehicle to the valet off position. This will ensure that

the vehicle remains protected at all times.

MANUALL Y OVERRIDING YOUR SYSTEM: USING THE PBLED OVERRIDE SWITCH

Your Security System can be disarmed without the use of the keychain transmitter. This is necessary, since you will need the ability to operate your vehicle if the transmitter is lost or its battery fails. If your system has been selected for Valet Switch manual override as indicated on the last page of this manual, to bypass the alarm system;

1. Open the vehicle door. The alarm will sound.

2. Turn the ignition key to the on position.

3. Within 5 seconds, press and release the PBLED override switch. The alarm system will stop sounding and enter the (bypassed) mode. You can now start and operate the vehicle normally. Typically this override mode is used only if the transmitter has become inoperative.

Programming Your Custom Override Code:

Unlike override switches easily found, and defeated, this security system allows the consumer to program a personal override code, offering a higher level of security. To take advantage of this option, programmable feature # 10 must be selected for the Custom Code Option. Consult your installation center for programming details. The system comes from the factory with a pre-programmed override code of 11. To change this default override code, do the following:

1. Disarm the system by use of the transmitter, or by use of the emergency override sequence. Turn the ignition switch to the on position.

2. Within 10 seconds, press and release the PBLED switch, 3 times.

3. Within 10 seconds turn the ignition switch off, on, off, on, off, on. (The siren or horn will beep and the lights will flash one time.)

4. Within 10 seconds, begin to enter your chosen 10ths digit by pressing and releasing the PBLED switch from 1 up to 9 times.

5. Within 10 seconds of the last entered 10ths digit, turn the ignition switch off then on.

6. Within 10 seconds, begin to enter your chosen units digit by pressing and releasing the PBLED switch from 1 up to 9 times.

7. Finish by turning the ignition switch to the off position.

If the new code was accepted, the unit will report back the newly entered code, by flashing the LED, first indicating the 10ths digit, pause and then the units digit. The unit will report the new code three times with a one second pause between each code, then the system will begin arming. If the LED flash pattern reports the previously stored code, the new code was not entered correctly. Please repeat steps 1 through 7 above considering the following. Note: Acceptable digits 10ths or units are 1 through 9. The unit will not recognize a 0 (Zero),

or no digit entered in any place, units or tenths.

Note: If 15 seconds of inactivity expire, or if the ignition switch is turned off for more then

5 seconds during any of the above steps, the unit will revert back to the last successfully stored code.

To Change the code from the factory pre-assigned code of 11 to “52” you would do the following:

1. Disarm the system by use of the transmitter, or by use of the emergency override sequence.

2. Turn the ignition switch to the on position.

3. Within 10 seconds, press and release the PBLED switch, 3 times.

Custom Code Programming Example:

Page 5

128-8190

5 of 8

Page 6

4. Within 10 seconds turn the ignition switch off, on, off, on, off, on. (The siren or horn will beep and the lights will flash one time.)

5. Within 10 seconds, begin to press and release the PBLED switch to set the tenths digit. (As per the example, press and release 5 times to set the tenths digit to 5)

6. Within 10 seconds of the last press of the pushbutton, turn the ignition switch off then on.

7. Within 10 seconds, begin to press and release the PBLED switch to set the units digit. (As per the example, press and release 2 times to set the units digit to 2).

8. Turn the ignition switch to the off position. Immediately observe the LED flash pattern.

Y ou will note the LED flashing five times, pause, and then flash two times, pause. This pattern will be repeated three times indicating the new code (52) has been accepted and stored in memory. Note: If after step 7, the LED flashes a code other than what was just entered, this indicates

that the code has not been changed. You will have to repeat steps 1 through 7 above

being certain to note the following: Acceptable digits 10ths or units are 1 through 9. The unit will not recognize a 0 (Zero), or no digit entered in any place, units or tenths. Note: If 15 seconds of inactivity expire, or if the ignition switch is turned off for more then 5 seconds

during any of the above steps, the unit will revert back to the last successfully stored code.

MANUALL Y OVERRIDING YOUR SYSTEM: USING THE CUSTOM CODE OVERRIDE

Assuming the override code programmed has not been changed, and the default override code of 11 is in the system's memory.

1) Enter the vehicle and turn the ignition switch to the on position. Note: The siren will sound.

2) Within 5 seconds, press and release the PBLED switch 1 time.

3) Within 5 seconds, turn the ignition switch off then on.

4) Within 5 seconds, press and release the PBLED switch 1 time.

5) Turn the ignition switch off then on and start the vehicle. Note: If you have changed the programmed override code then substitute your new code

tenths for step 2 above, and units for step 5 above.

ELIMINATING THE NORMAL ARM/DISARM CHIRPS

Y ou can selectively eliminate the normal arm & disarm chirps by holding the transmitter button slightly longer when arming or disarming. This will prevent the siren chirps for one arm or disarm cycle. If you find this inconvenient and wish to eliminate these chirps permanently,

1. Turn the ignition switch 'on" then 'off".

3. Within 10 seconds of turning off the ignition, press and release the PBLED switch 3 times.

4. If the chirps were on before you started, the siren will emit 2 short chirps indicating that the

chirps are now off. If the chirps were off before you started, the siren will emit one short chirp indicating that the chirps are now on.

Note: If the vehicle battery is disconnected then reconnected, the unit will return to the

default setting of chirps on. Repeat the above procedure to eliminate the arm/disarm

chirps.

REMOTE PANIC OPERA TION

The ARM or DISARM button on your keychain transmitter also functions as a panic switch for use in emergency situations. To use remote panic,

1. Press and hold the ARM or DISARM button on the keychain transmitter for 3 or more seconds. The alarm will immediately sound.

2. T o stop the alarm, press and hold the ARM or DISARM button on the transmitter again for 3 seconds. If the button is not pressed, the alarm will automatically stop after 30 seconds. Also if any transmitter button other than the ARM or DISARM button is pressed and released, the Panic mode will be turned off immediately. The normal function of this transmitter button will be suspended during the Panic sounding period.

3. During the panic mode, the Lock and Unlock buttons can be used to lock and unlock the doors, (if the option is installed), however once the unlock/disarm button is pressed, the vehicle's starter inhibit device, (where installed) will be disabled allowing the vehicle to start.

Page 6

128-8190

6 of 8

Page 7

Note: While in the Panic mode, pressing and releasing the ARM or DISARM buttons will,

ADDITIONAL REMOTE FUNCTION ( CHANNEL 3 )

This security system has an additional features that can be connected to a number of different optional accessories. Some of the more common uses for this channel are;

Operation of the optional accessory or accessories, can be controlled by pressing and holding the programmed button on the keychain transmitter for four seconds, or by pressing and releasing the programmed button on the transmitter two times in succession. Check with your installation center for more information on what accessories were installed and how they are accessed.

ADDITIONAL REMOTE FUNCTION ( CHANNEL 4 )

This security system has an additional feature that can be connected to a number of different optional accessories. Some of the more common uses for this channel are;

To activate the optional accessory, press the programmed button on the keychain transmitter for up to 8 seconds for continuous output, or press and release for momentary activation. The optional accessory will immediately engage. Check with your installation center for more information on the optional accessory that may have been installed and how it is accessed.

ADDITIONAL REMOTE FUNCTION ( CHANNEL 5 )

This security system has an additional feature that can be connected to a number of different optional accessories. Some of the more common uses for this channel are;

if the option is installed, lock and unlock the doors respectively. While in the panic mode, anytime the DISARM button is pressed, the panic feature will continue for the allotted 30 seconds, however, the security system will be disarmed allowing the vehicle to start.

 Remote Trunk Release  Remote Car Starter  Remote Window Closure  Remote Garage Door Interface

IGNITION CONTROLLED LOCK UNLOCK: (Unlock Drivers Only, or Unlock All Doors) Your security system has a selectable safety feature that allows the vehicle doors to lock

when the ignition switch is turned on, (Providing all doors are closed), and to unlock the doors when the ignition switch is turned off. In addition, the unlocking of the doors is further selectable, in a two step unlock configuration, to unlock only the drivers door or all doors.

Page 7

128-8190

7 of 8

Page 8

SYSTEM FUNCTIONS A T A GLANCE

DASH LED INDICAT ORS

RAPID FLASHING = PASSIVE ARMING SLOW FLASHING = ARMED OFF = DISARMED ON SOLID = V ALET MODE 3 FLASH...PAUSE = INTRUSION ZONE 3 2 FLASH...PAUSE = INTRUSION ZONE 2 1 FLASH...PAUSE = INTRUSION ZONE 1

SIREN CHIRP INDICA TORS

*1 CHIRP = ARM *2 CHIRPS = DISARM 3 CHIRPS = ARM / DOOR OPENED 4 CHIRPS = DISARM / INTRUSION

* These chirps are optional, and can be de-activated.

PARKING LAMP INDICA TORS

1 FLASH = ARM 2 FLASHES = DISARM 3 FLASHES = DISARM / INTRUSION

PRO-9649b

Your System Has These Features Activated

 Starter Disable  Remote Keyless Entry  Auto Lock with ignition key  Auto Unlock with ignition key  Passive Arming  No Lock in passive mode  Hardwire doors, hood, and trunk  Custom Code Override  Valet Switch Override

128-8190

8 of 8