Audiovox PRO 9445FT User Manual

Model PRO 9445FT

Installation Manual

REMOTE KEYLESS ENTRY

PRE-INSTALLATION NOTES:

DIP SWITCHES :

This unit incorporates three on - board dip switches for selection of optional features. They are;

ON OFF
Dip Switch #1 Auto Lock/Unlock No Auto Lock/Unlock
Dip Switch #2 Passive Lock Active Locks
Dip Switch #3 Passive Starter Inhibit Active Starter Inhibit

STARTER DISABLE:

This system provides a transistorized output to control the starter cut feature.

When the starter cut relay is installed, any time the doors are remotely locked, the vehicle's starting circuit is disabled.
Additionally, when the passive starter cut feature is selected (dip switch #3 On), then 30 seconds after leaving the vehicle,
the vehicle's starting circuit will be automatically disabled.

CHANNEL 2 OUTPUT:

This system provides an additional hardwire remote output to control an assortment of optional upgrades. This output
is an independent channel from the transmitter, and is controlled by the (Option) button of the transmitter. It is a delayed
ground pulse (300 mA maximum), and can be used to control;

Optional Trunk Release Relay AS-9256

Optional Remote Starter AS-9151N / AS-9075

Optional Window Roll Up AS-9153

Optional Garage Door AS-9154

Additionally, if both transmitter buttons are designated, the remote transmitter has the capability of transmitting a third
RF signal that can be used to operate a second vehicle equipped with a similar Pursuit alarm. By simultaneously
pressing both the "Lock/Unlock" button along with the "Option" button, a third function can be operated.

DOOR LOCK / UNLOCK OUTPUTS:

This system provides both (+) and (-) pulsed door lock outputs for direct connection to most OEM factory installed door
lock control relays. These outputs have a maximum current capability of 300 mA, and external relays must be used for
switching circuits requiring more than 300 mA, and with 4 or 5 wire polarity reversal door lock control circuits. The optional
AS-9159 Door Lock Interface is available to simplify the wiring of these types of circuits.

INSTALLATION OF MAJOR COMPONENTS:

CONTROLMODULE:

Select a mounting location inside the passengercompartment( up behind the dash ), andsecureit using screws,
or cable ties.

DO NOT mount the control module in the engine compartment, as it is not waterproof.
DO NOT mount the unit or route the wiring near the steeringshaft,asitmightbecomeentangled,preventing proper

operation of the vehicle.

1

VALET SWITCH:

Select a mounting location for the switch that is easily accessible to the driver of the vehicle.

The switch does not have to be concealed, however concealing the switch is always recommended, as this provides
an even higher level of security to the vehicle.

The switch is mounted by drilling a 1/4" diameter hole in the selected location. Be sure to check behind the dash for
adequate clearance for the body of the switch, and to confirm the drill will not damage any existing components as it
passes through the dash.

WIRING THE SYSTEM:

RED w/WHITE TRACE FUSEDWIRE: +12 VDC CONSTANT BATTERYSOURCE

Connect the Red w/White tracer wire to a +12 VDC battery source.

YELLOW WIRE : +12 VDC IGNITION SOURCE

Connect this wire to a source that has + 12 volts when the key is turned to the start and run positions, and has 0 volts
when the key is in the off position.

BLACK WIRE : CHASSIS GROUND

Connect this wire to a solid, unpainted, metal part of the vehicle's chassis.

Do not confuse this wire with the thin black antenna wire that exits the control module independently.

PURPLE WIRE : + DOOR TRIGGER

If the vehicle's door courtesy light switches +12 volt to the interior light circuit when a door is opened, connect the Purple
wire to the positive switched wire from the driver's door pin switch.

WARNING: Do not use the purple wire if the vehicle has ground output type door switches. (see BROWN WIRE)

BROWN WIRE : - DOOR TRIGGER

If the vehicle's door courtesy light switches ground to the interior light circuit when a door is opened, connect the Brown
wire to the ground switched wire from the driver's door pin switch.

WARNING: Do not use the brown wire if the vehicle has +12 volt output type door switches. (see PURPLE WIRE)

NOTE: I n al l installations, either the Purple or Brown door pin switch wires must be used. This wire prevents

automatic locking of the doors if the ignition is turned on while the door is open or ajar.

ORANGE WIRE : 300 mA GROUND OUTPUT WHEN LOCKED

This is the output control for the starter cut relay. Connect the Orange wire to terminal 86 of the AS-9256 relay (or an
equivalent 30 Amp. automotive relay). Wire the remaining relay contacts as shown in the wiring diagram.

DARK GREEN w/WHITETRACEWIRE:ENTRYILLUMINATION

This wire provides a 30 second ground signal whenever the doors are unlocked using the remote transmitter, and is
used to control the optional entry illumination feature. This output is also used to provide feedback information when
programming the transmitters.

This is a low current (300 mA) transistorized output, and should only be used to drive an external relay coil. Connect
the Dark Green w/White trace wire to terminal 86 of the AS-9256 relay (or an equivalent 30 Amp. automotive relay),
connect terminal 85 of the relay to a fused +12 VDC battery source, and wire the normally open and common (87 & 30)
relay contacts according to the polarity of the vehicle's courtesy light circuit.

2