Page 1
TM
SERIES
Table Of Contents:
Before You Begin Page 2
Wire Harnesses Quick View Page 3
Mounting Of The Major Components Page 5
14 Pin Accessory Input/Output Harness Wiring Page 5 - 7
2 Pin Door Lock/Unlock Connector & Wiring Page 7
5 Pin Arm/Disarm/Trunk Shunt Inputs Page 7 - 8
2 Pin LED / Valet Connectors Page 9
Programming Alarm Feature Page 9 - 11
Telematic Upgrade Port Information Page 11
Completing Your Installation Page 11
Dome Delay Learning Proceedure Page 11
Adjusting The Shock Sensor Page 11
Wire Dressing Page 11
Circuit Wiring Layout Page 12
Model PRO9233E
Installation Manual
Factory Keyless Entry Alarm
Upgrade System
PATENTED: www.voxxintl.com/company/patents
Page 1
128-9324
1 of 12
Page 2
Before You Begin
PROFESSIONAL INSTALLATION IS
STRONGLY RECOMMENDED
Roll down window to avoid locking the keys in the vehicle during installation.
Avoid mounting components or routing wires near hot surfaces or near
moving parts like the steering wheel as it may prevent proper operation of the
vehicle.
Tape or loom wires under the hood and dash for protection as well
appearance.
Use grommets when routing wires through metal surfaces to prevent chafi ng
and shorting.
Use a Digital Multi Meter for testing and verifying circuits. DO NOT USE A
"TEST LIGHT" OR "COMPUTER SAFE PROBE" as these can set off air bags
or damage sensitive vehicle computers and electronics.
For technical support go to www.prestigecarsecurity.com
or call 1 800 225 6074
PATENTED: www.voxxintl.com/company/patents
Page 2
128-9324
2 of 12
Page 3
14 Pin Main Wiring Harness Part # 1123895
1
2
3
4
5
6
7
8
9
10
11
12
13
14
Red (+) 12 Volts Parking Light Input
White
(+) Parking Light Output 15A Max
Red/White + 12 Volt Module Input
White/Black (+) Positive Siren Output
Purple Positive Door Trigger Input
Yellow Ignition Input Switched +12 Volts
Green/White Illumination Entry Output (-) 300mA
Black/White Horn Output (-) 300mA
Black Chassis Ground
Orange Ground Output While Armed (-) 300mA
Brown Negative Door Trigger Input
LT. Green Negative Trigger Input Zone 1
DK. Green Negative Hood / Trunk Trigger Input
Green/Black Auxiliary Output (-) 300mA
5 Pin Arm/Disarm Trunk Shunt I/O Harness Part #1123237
1
2
3
4
5
Green/Black Arm 2 Input
Red Disarm 1 Input
Green Arm 1 Input
Red/Black Disarm 2 Input
Blue Trunk Shunt Input
2 Pin Door Lock Output Harness Part #1122242
1
2
Red Neg. Lock / Pos. Unlock 300mA Max
Green Pos. Lock / Neg. Unlock 300mA Max.
Page 3
128-9324
3 of 12
Page 4
PRE - INSTALLATION NOTES :
This system provides an output that is used to drive the siren, and an output that can pulse the vehicle's horn.
When utilizing the horn, an additional relay maybe required. Caution: on many vehicles the factory horn is not
designed for continuous use, and it is recommended that the siren is used for these vehicles. Check to see if the
horn in the vehicle is the same part that is used in a vehicle with the factory installed security system
ST AND ALONE PASSIVE ALARM:
When installing this unit as a stand alone passive alarm system, the following programmable features must be set:
Feature #5 set to Passive.
Feature #7 set to Delay.
Feature #8 set to 1 Wire Disarm.
IMPORT ANT:
In the entry delay mode, when the alarm is armed, the doors will trigger the alarm 15 seconds after the
door is opened.
IMPORT ANT:
THE ENTRY DELA Y WILL NOT OPERA TE WHEN THE VOLT AGE SENSING CIRCUIT , FEATURE # 6, IS ACTIVE
AUXILIARY FUNCTION or REMOTE START OUTPUT:
This system includes an additional transistorized ground output that can be used to trigger an external remote
starter or remote window closure module. This is the Green w/Black trace wire, and it is activated by pressing
the Lock, then Unlock, then Lock buttons on the factory transmitter within a 3 second time period.
REMOTE PANIC:
This system will allow the activation of remote panic using the factory transmitter. Pressing the Unlock, the Lock,
then Unlock buttons on the factory transmitter within a 3 second time period will activate the remote panic feature.
TRUNK SHUNT/TRIGGER BY - PASS INPUT:
This system provides a positive trunk release input, which allows the activation of the remote trunk release from
the OEM transmitter without triggering the alarm, even when the system is armed.
VALET / MANUAL OVERRIDE SWITCH:
This system provides a selectable manual override which, in the simple mode, is operable by fi rst turning on the
ignition switch then pressing the override pushbutton switch one time, or by a custom code override which is fully
explained in the owners. The valet circuit is available only after the system is disarmed, then with the ignition on,
press and hold the pushbutton LED switch until the LED turns On.
UNDERSTANDING ARM & DISARM #1 AND #2:
Because of the complexities of the different factory installed Remote Keyless Entry Units on the market today,
this system uses two disarm and two arm inputs. Whether installing into a vehicle using a 2-step unlock circuit,
single step unlock circuit, or as a stand alone passive alarm, both disarm and arm wires must be connected in
all installations.
The arm and disarm functions of this system are learned during power up, by monitoring the resting state of the
factory wires when power is applied to the unit. Be certain all wires are connected to the vehicle before applying
power to the circuit to insure the system responds only during operation from the factory transmitters.
NOTE: By design, if feature #8 is set to the "1 WIRE DISARM" selection, the alarm will not disarm while the
system is in the triggered mode.
You will note in the feature selection table a selection for OR, and a selection for AND. In the OR confi guration if
either of the arm, or disarm wires have a state change, the circuit will invert and either arm or disarm.
Page 4
128-9324
4 of 12
Page 5
In the AND confi guration, both wires must invert to have a state change at the alarm module to either arm or dis-
arm. In the OR confi guration a typical connection would be the Drivers Door Motor, and the Drivers Door Switch.
This will allow the unit to arm from the factory keyless entry transmitter and not be armed or disarmed from the
door switch.
In the AND confi guration, if there is no door switch available or it is inaccessible, you can connect to the drivers
motor leg and the parking light which typically activates from the factory transmitter.
In either case, the factory transmitter should allow the circuit to arm and disarm, however, the in vehicle door
switch should not. Please confi rm proper operation once the unit is installed.
INSTALLATION OF MAJOR COMPONENTS
ALARM CONTROL MODULE : P/N 1365420
Select a mounting location inside the passenger compartment ( up behind the dash ), and secure it using screws, or
cable ties. Do not mount the control module in the engine compartment, as it is not waterproof. Do not mount the unit
or route the wiring near the steering shaft, as it might become entangled preventing proper operation of the vehicle.
PUSHBUTTON LED SWITCH: P/N PRLED
Select a mounting location known and accessible to the operator of the vehicle. A dash knockout plug or front dash
panel is desirable as the now Push-Button LED assembly needs the LED to be visible from the outside of the vehicle
and will be used for valet modes, programming features, and for overriding the system unit when the vehicle is being
serviced. Inspect behind the chosen location to insure that adequate clearance is allowed for the body of the switch,
and also that the drill will not penetrate any existing factory wiring or fl uid lines. Drill a 5/16" or 8mm hole in the desired
location and mount the switch by passing the connectors, one at a time, through the panel from the front side and
pressing on the bezel until the switch is fully seated.
OPTIONAL SIREN: P/N AS9903E
Select a mounting location in the engine compartment that is well protected from access below the vehicle. Avoid areas
near high heat components or moving parts within the engine compartment. To prevent water retention, the fl ared end
of the siren must be pointed downward when mounted.
Mount the siren to the selected location using the screws and bracket provided.
HOOD OR TRUNK PIN SWITCH: P/N 1363699
A pin switch is included for use in protecting the hood or trunk (or hatchback) of the vehicle. The switch must
always be mounted to a grounded, metal surface of the vehicle. It is important to select a location where
water cannot fl ow or collect, and to avoid all drip gutters on hood and trunk fender walls. Choose locations
that are protected by rubber gaskets when the hood or trunk lid is closed.
The pin switch can be mounted using an optional bracket, or direct mounted by drilling a ¼ “ diameter
mounting hole. Keep in mind that when properly mounted, the plunger of the pin switch should depress at
least ¼ “ when the hood or trunk lid is closed.
WIRING THE SYSTEM
14 PIN MAIN WIRING HARNESS CONNECTOR P/N 1123895
RED FUSED WIRE: + 12 VDC CONSTANT BATTERY SOURCE
In all installations, the RED wire will be connected to a + 12 VDC constant battery source.
Connecting the Red wire not only supplies power to the on-board parking light relay, it also connects the Red/White
module's power wire.
WHITE WIRE : + 12 VDC PULSED PARKING LIGHT OUTPUT ( 15 A MAX )
This wire is provided to fl ash the vehicle’s parking lights. Connect the WHITE wire to the positive side of one of the
vehicle’s parking lights.
Page 5
128-9324
5 of 12
Page 6
RED/WHITE : (+) 12 VOLT MODULE's POWER
See RED Wire above.
WHITE w/ BLACK TRACE WIRE : POSITIVE OUTPUT TO SIREN
This is a + 12 VDC transistorized switched output when triggered.
Connect this wire to the red, positive wire of the siren. Secure the black, ground wire of the siren to chassis ground.
PURPLE WIRE : (+) DOOR TRIGGER
If the vehicle’s door courtesy light switches have a + 12 VDC output when the door is opened (most Fords), you must
connect this wire to the positive output from one of the door switches. Do not connect this wire at the illuminated entry
output from the keyless entry module. You must connect this wire at the door ajar switch. In most cases, the PURPLE
wire will only need to be connected to one door switch, no matter how many doors the vehicle has.
IMPORTANT! Do not use the PURPLE wire if the vehicle has ground output type door switches. (See BROWN
wire).
NOTE: For vehicles with interior delay lighting see programming under title "Completing The Installation".
YELLOW WIRE : + 12 VDC IGNITION SOURCE
Connect this wire to a source that is + 12 VDC when the key is in the on and crank positions, and off when the key is
in the off position.
DARK GREEN w/ WHITE TRACE WIRE : ENTRY ILLUMINATION ( 300 mA MAX. )
The Dark Green w/ White Trace wire provides a 30 second ground signal whenever the system is disarmed using the
OEM transmitter, and pulses ground when the alarm is triggered.
It is used to provide the optional entry lighting feature and will fl ash the vehicle’s dome light when the alarm is sound-
ing. This is a transistorized, low current output, and should only be used to drive an external relay coil. Connect the
DARK GREEN w/ WHITE TRACE wire to terminal 86 of an external relay, connect terminal 85 of the relay to a fused
+ 12 VDC battery source, and wire the normally open and common relay contacts ( 87 and 30 ) according to the polarity
of the vehicle’s courtesy light circuit.
BLACK w /WHITE TRACE WIRE: LOW CURRENT HORN OUTPUT
The black w/ white trace wire is provided to beep the vehicle’s horn. This is a transistorized low current output, and
should only be connected to the low current ground output from the vehicle’s horn switch.
If the vehicle uses a + 12 VDC horn switch, then connect the black w/ white trace wire to terminal 86 of the AS 9256 relay
( or an equivalent 30 Amp automotive relay ), and connect relay terminal 85 to a fused + 12 VDC battery source. Connect
relay terminal 87 to the vehicle’s horn switch output, and connect relay terminal 30 to a fused + 12 VDC battery source.
BLACK WIRE : CHASSIS GROUND
Connect this wire to a clean, solid, unpainted, metal part of the vehicle’s chassis.
ORANGE WIRE : GROUND OUTPUT WHEN ARMED
This wire is provided to control the starter cut relay . Connect the ORANGE wire to terminal 86 of the relay, and wire the
remaining relay contacts as shown in the wiring diagram.
WARNING! Audiovox does not recommend using this relay to interrupt the ignition wire. Only connect this
BROWN WIRE : (-) DOOR TRIGGER
If the vehicle’s door courtesy light switches have a negative ground output when the door is opened (most GM and
Imports) you must connect this wire to the negative output from one of the door switches. Do not connect this wire at
the illuminated entry output from the keyless entry module. You must connect this wire at the door ajar switch. In most
cases, the BROWN wire will only need to be connected to one door switch, no matter how many doors the vehicle has.
IMPORTANT! Do not use the BROWN wire if the vehicle has + 12 V olt output type door switches ( see PURPLE
wire).
NOTE: For vehicles with interior delay lighting see programming under title "Completing The Installation".
relay to the low current start solenoid feed wire, as indicated on the wiring diagram.
Page 6
128-9324
6 of 12
Page 7
LIGHT GREEN WIRE : (-) INSTANT TRIGGER ZONE 1
This is an instant activation ground trigger wire. This wire should be reserved for connection to optional ground output
trigger devices such as motion, glass breakage and/or non plug in shock sensors.
DARK GREEN WIRE : (-) INSTANT TRIGGER ZONE 2
This is an instant activation ground trigger wire. It should be connected to the previously installed hood and or trunk
pin switches.
GREEN w/BLACK TRACE WIRE : AUXILIARY OR REMOTE STARTER OUTPUT
This wire provides a low current transistorized ground pulse to control the input trigger wire of a remote starter or window
roll-up module. Connect this wire to the ground activated trigger input wire of the optional device.
2 PIN WHITE CONNECTOR : RED AND GREEN DOOR LOCK OUTPUTS (Auto Lock / Unlock)
The door lock output wires from this unit will provide control for the passive lock feature as well as ignition controlled
lock and unlock feature, and should be used only on vehicles whose Factory Keyless Entry circuits do not incorporate
these features.
These wires will provide either a pulsed ground output to the factory door lock control relay , or a pulsed +12 volt output
to the factory door lock control relay . In either case, the maximum current draw through these outputs must not exceed
300 mA.
3 Wire Ground Switched Door Locks
In this application, the red wire provides a ground pulse during the lock sequence. Connect the red wire to the wire that
provides a low current ground signal from the factory door lock switch to the factory door lock control relay. The green
wire provides a ground pulse during the unlock sequence. Connect the green wire to the wire that provides a low current
ground signal from the factory door unlock switch to the factory door unlock control relay.
3 Wire Positive Switched Door Locks
In this application, the red wire provides a positive pulse during the unlock sequence. Connect the red wire to the wire
that provides a low current positive signal from the factory door unlock switch to the factory door unlock control relay.
The green wire provides a positive pulse during the lock sequence. Connect the green wire to the wire that provides a
low current positive signal from the factory door lock switch to the factory door lock control relay.
4 Wire Polarity Reversal and 5 Wire Alternating 12 Volt Door Lock Control Circuits
In these applications, a Door Lock Interface (or equivalent 30 A automotive relays) must be used. Refer to the AUDIOVOX Door Lock Wiring Supplement for proper connection to these types of circuits and current model door lock
interfaces to use.
5 PIN WHITE CONNECTOR: ARM/DISARM/TRUNK SHUNT INPUTS P/N 1123237
NOTE! When installing this system as a stand alone passive security system, the RED wire in this connector
must be connected to a rest at ground, + 12 VDC switched ignition source. RED w/BLACK,
GREEN & GREEN/BLACK wires must be connected to ground. The BLUE wire in this connector will
not be required for the stand alone installation.
The Green/Black, Red, Green, and Red/Black wires of the 5 pin connector are polarity learning inputs to be connected
to the vehicle lock & unlock 1, and lock & unlock 2 control wires. When the control circuit is fi rst powered up, these
wires will learn the resting state of the circuits they are connected to. DO NOT operate the vehicle's door lock circuits,
(switch or remote), while power is being applied to this upgrade alarm system.
WIRING THE ARM / DISARM INPUTS IN VEHICLES WITH REMOTE 2 STEP UNLOCK,,
FEATURE SELECTION 11 SET FOR OR
The following represents the most common wiring routine in vehicles using the remote 2 step unlock feature.
GREEN/BLACK WIRE : ARM INPUT #2
Connect this wire to the vehicles door lock switch input wire, which will receive either a switched positive or
switched negative when the door lock switch is moved to the lock position. This wire will be used to compare
Page 7
128-9324
7 of 12
Page 8
the two inputs Arm #1 & Arm #2. If both inputs are active at the same time, the vehicle will not arm. The
intent of this wire is to prevent the system from arming when the in vehicle door lock switch is used to lock
the doors, insuring only the transmitter arms the system. If you do not desire this feature or the customer
prefers that the door lock switch arm the system as well as the transmitter, connect this wire to chassis ground.
RED WIRE : DISARM INPUT #1
Connect this wire to the driver's door unlock motor wire, which will receive a negative or positive pulse when
the drivers door is unlocked with the remote transmitter, and the door switch, but does not receive a pulse
when all doors are unlocked using the remote transmitter.
GREEN WIRE : ARM INPUT #1
Connect this wire to the lock side of the door lock/unlock switch or, the driver's door lock motor leg wire,
which will receive a negative or positive pulse when the doors are locked using the door switch or the remote
transmitter.
RED w/BLACK TRACE WIRE : DISARM INPUT #2
Connect this wire to the unlock side of the door lock/unlock switch or any passenger door unlock motor wire,
which will receive a negative or positive pulse when all doors are unlocked using the door panel switch or
the remote transmitter, but will not receive a pulse when the driver only door is unlocked using the
remote transmitter.
NOTE: The Green/Black/Red/ Green/& Red/Black wires MUST be connected to their respective source
before powering up the module as these wire are polarity learn and will not function properly if connected
after power up. In addition, these wires if not used as indicated above must be connected to ground.
This will insure proper operation and prevent inadvertent arming and disarming when unintended.
BLUE WIRE : TRUNK TRIGGER SHUNT INPUT
This wire will determine if the vehicle’s trunk has been opened using the OEM transmitter, and prevent the
alarm from triggering when the transmitter is used. This wire requires a positive trigger input and must be
wired to the switched + 12 volt trunk control wire from the vehicle's keyless entry unit or, the switched + 12
volt side of the vehicle's trunk release solenoid.
WIRING THE ARM / DISARM INPUTS IN VEHICLES WITH REMOTE
FEATURE SELECTION 11 SET FOR AND
This appllication is for vehicle's that have a 2nd unlock unavailable or diffi cult to access.
GREEN/BLACK WIRE: ARM INPUT #2
Connect this wire to the vehicle's Parking light wire providing the parking lights are active when the transmitter
is used to lock the vehicle doors.
RED WIRE: DISARM INPUT #1
Connect this wire to the driver's door unlock motor wire, which will receive a negative or positive pulse when
the drivers door is unlocked with the remote transmitter.
GREEN WIRE : ARM INPUT #1
Connect this wire to the driver's door lock motor leg wire, which will receive a negative or positive pulse when
the doors are locked using the the remote transmitter.
RED w/BLACK TRACE WIRE : DISARM INPUT #2
Connect this wire to the vehicle's Parking light wire providing the parking lights are active when the transmitter
is used to lock the vehicle doors.
BLUE WIRE : TRUNK TRIGGER SHUNT INPUT
Please follow information listed above for this wire connection and operation.
Page 8
128-9324
8 of 12
Page 9
WIRING THE ARM / DISARM INPUTS IN VEHICLES WHEN THE SYSTEM IS SET UP AS A
STAND ALONE PASSIVE (IGNITION CONTROL) ALARM SYSTEM
For this mode of operation, be certain to set selectable features #5 for passive, #7 for delay , and #8 for 1 wire disarm.
GREEN/BLACK & GREEN WIRE: ARM INPUTS
Connect these wires to chassis ground.
RED WIRE : DISARM INPUT #1
Connect this wire to an ignition source that has +12 volts when the ignition switch is turned to the on and start positions
and has 0 volts when the switch is in any other position.
RED w/BLACK TRACE WIRE: DISARM INPUT #2
Connect this wire to chassis ground.
BLUE: TRUNK SHUNT INPUT
This wire is not used for the stand alone passive alarm application.
VALET SWITCH:
Plug the 2 pin connector from the push-button valet/LED switch into the mating 2 pin connector on the control module.
LED: Plug the 2 pin connector from the push-button valet/LED switch into the mating 2 pin connector on the control
module.
PROGRAMMING (ALARM FEATURES):
1) Turn the ignition key to the on position.
2) Press and release the valet/programming switch 3 times (Siren Chirps).
3) Turn the ignition key off then on. (Siren Short Then long Chirp)
4) Press the pushbutton switch once to advance to feature 1, twice to advance to feature 2, etc,,,then use
the lock button of the factory transmitter, or the lock switch on the door to select the feature setting.
Example to set passive arming:
1) Turn the ignition key to the on position.
2) Press and release the valet/programming switch 3 times (Siren Chirps).
3) Turn the ignition key off then on. (Siren Short Then long Chirp)
4) Press the pushbutton switch six times to advance to features 6, Pass/Act Arm, then use the lock button
of the transmitter to select two chirps "Passive Arm".
5) T o exit the programming mode, turn the ignition key off. The program mode is automatically exited when
there is no activity on the pushbutton switch or the factory transmitter or in vehicle lock switch.
Page 9
128-9324
9 of 12
Page 10
SELECTABLE FEATURES
in the owners guide
The selectable features of this unit can be set manually as explained on the previous page.
Factory default settings are indicated by BOLD text.
NOTE : The method of manual override can either be selected to operate from the valet switch or operate by custom code. Custom Code programming is found
Be certain to place a check mark indicating the method used in the box located on the last page of the owner's manual.
NOTE: Keyless Entry Models with no horn output will Flash the Parking Lights instead of chirp where chirp is indicated.
Also, No data will be indicated if a feature is not available for a particular model. The unit will enter the feature but no selection will be available.
RF Programmable Feature Bank 1 Is For Transmitter Programming See Transmitter Programming Guide.
RF Programmable Features Bank 2 Is Alarm Selectable Features:
Feature Selection 1 Chirp 2 Chirps 3 Chirps 4 Chirps 5 Chirps 6 Chirps
1st DoorL/UL 1 Sec. 3.5 Sec. 1Sec. L, Dbl. U/L Dbl L, 1Sec. UL Dbl L, Dbl UL 1Sec. L/350mS ul
2nd Accy Lock Auto Lock On Auto Lock Off
3rd Accy. UL Auto UL On Auto UL Off
4th Passive Locks Passive Active
5th Pass/Act Arm Passive Arm Active Arm
6th Door Trigger Instant Delay
7th 1 or 2 Wire Disarm 1 Wire 2 Wire
8th Siren/Horn Siren/Horn Siren Only Horn Only
9th Horn Chirp 10mS 16mS 30mS 40mS 50mS
10th O/R Method Custom Code Valet
11th 14th L/UL Poll 120mS XOR 80mS XOR 120mS AND 80mS AND
UL Dr & Pass UL Dr & Pass UL + Light UL + Light
Page 10
128-9324
10 of 12
Page 11
NOTE: The program mode is exited if any of the following occur:
a. 15 seconds of inactivity expire during any of the above steps.
b. The ignition key is turned off.
c. The push button switch is activated more than 12 times .
The Siren/Horn will emit a long chirp followed by a short chirp indicating the program mode has been exited.
4 Pin Upgrade Telematic Module:
Red = + 5 Volts
Black = Ground
White = Data TX
Yellow = Data RX
If used, connect the 4 pin harness from the T elematic one way module kit to the mating port on the controlling
circuit. NOTE: If using the TWO WAY Telematic module, only Ground, TX, and RX are used on this port,
the + 12 volt supply for the two way module must be sourced separately or the unit will not operate.
4 Pin Upgrade Data Bus/Flash Logic Module:
If you are using an Audiovox Flash Logic module, it can be connected directly to the upgrade alarm system.
Using the Blue 4 pin blue, red, black, & white harness and connect to the mating connector on the control
module. Wire the Flash Logic/Data Bus module to the vehicle as prescribed in it's installation guide.
COMPLETING THE INSTALLATION
After all wire connections have been made, plug the main 14 pin connector into the control module. During the fi rst few
seconds of power up, the circuit's processor learns the resting state of the Red, Red/Black, Green and Green/Black
wires of the 5 pin connector. It is important that the ignition switch be off, and the door lock/unlock switch or transmitter not be used during the power up sequence. Once this sequence is complete, you can disarm the system with the
customers transmitter and move onto programming the selectable features.
NOTE: This unit has the ability to learn the dome light delay time, up to 60 seconds. If the vehicle has delay interior
lights, and you wish to avoid three chirp, defect zone, indication normally associated with this type of interior light, we
suggest you learn the interior light delay.
To learn the light delay, start with all doors closed:
1. Use the transmitter to Lock / Unlock / Lock / Unlock / Lock / Unlock / Lock, the system;
The LED turns on solid to confi rm the system entered the learn mode.
2. Immediately open and close the door of the vehicle to initiate the dome delay;
The unit will monitor the door trigger input Positive, (Purple), and Negative, (Brown) when active.
When the dome light turns off, the unit will add 2 seconds then exit the learn mode.
3. The LED will begin fl ashing the Armed indication indicating the unit has exited the learn mode and is
armed
Adjusting the Shock Sensor: P/N AS9492a
If used, the sensitivity of the pre- etect circuit is automatically set 30% less sensitive than the full trigger circuit.
Using a small screwdriver, gently turn the adjustment screw fully counterclockwise. (DO NOT over turn this
screw. Maximum rotation for this adjustment is 270°). Close the hood and trunk lids, and arm the alarm.
Wait 6 seconds for the accessories trigger zone to stabilize, then fi rmly strike the rear bumper with the side
of a closed fi st considering the amount of force required to break a window.
WARNING ! Never perform this test on the vehicle’s glass, as you may break the window.
Turn the adjustment screw clockwise (increasing sensitivity) about ¼ turn and re-test. Repeat
this procedure until the alarm sounds. Ultimately , one fi rm strike to the rear bumper will cause
the alarm to emit pre-detect warning tones.
CAUTION: Setting the sensitivity too high can cause false alarms due to noise vibrations from passing
trucks and heavy equipment. To decrease sensitivity, turn the adjustment screw counter
clockwise.
Wire Dressing:
Always wrap the alarm wires in convoluted tubing, or with a spiral wrap of electrical tape. Secure these looms
along the routing using cable ties. This will ensure that the alarm wires are not damaged by falling onto hot
or sharp moving surfaces in the vehicle.
Page 11
128-9324
11 of 12
Page 12
Green/Black Arm2
Red Disarm 1
Green Arm 1
Red/Black Disarm 2
Blue Trunk Shunt
Pushbutton
LED Assembly
Red = (-) Lock (+) Unlock
Green = (+) Lock (-) Unlock
Left Parking Lamp Right Parking Lamp
-
Red
Green
(+) 12 Volt Supply To
Parking Light Relay
& Control Module
-
Red
White
PRO9233E
PRO9233E
Red/White
15A
5A
Red (+)
Black (Ground)
Green (Full Trigger)
Blue (Pre Detect)
To Shock Sensor
Green/Black
Dark Green
LT. Green
To Optional One
Or Two Way
Telematic Module
To FlashLogic Module
When Being Used
Auxiliary Output (-) 300mA
Can Be Used For Remote Start
Trunk Release
Window Roll Up
(-) Tigger Input Connect
To Hood & or Trunk Pin
Switch
(-) Trigger Input Zone 1
Connect To Optional
Negative Triggering Device
To (+) Side Of
Optional Siren
(+) Positive Door Trigger Input
Connect To Existing Door Pin
Circuit In Vehicle
Ignition Input
Connect To + 12 Volts
Ignition / Crank
To Entry
Illumination
Wire Of Vehicle
Connect to (+) If Vehicle’s
Interion Light Switched (+)
Connect to (-) If Vehicle’s
Interior Light Switched (-)
White/Black
Purple
Yellow
Orange (- Starter Inhibit Output)
Black
Brown
Green/White
86
87a87
85
30
To Fused + 12 Volt Source
Black/White
Black/White
(-) Negative Door Trigger Input
Connect To Existing Door Pin
Circuit In Vehicle
To Starter Motor
Low Current (-) Output To
Operate Vehicle’s Horn Relay
Black/White
Chassis Ground
Cut
X
30
87a
87
Existing Low Current
Start Solenoid Wire
Black
8586
©2014 Voxx Electronics Corp., 150 Marcus Blvd. Hauppauge, N.Y. 11788 128-9324
Page 12
128-9324
12 of 12
From Ignition Switch
Start Terminal
To + 12 Volt
Ignition / Start
Loading...