Audiovox PRO 9233 User Manual
Model PRO 9233
OWNER’S MANUAL
KEYLESS ENTRY ALARM UPGRADE MODULE
Congratulations on your purchase of the PRO9233 automotive Keyless Entry
Upgrade Alarm System. This system is a state - of - the - art auto security system
that is designed to automatically arm and disarm when it receives a command from
your existing Factory Keyless Entry Transmitter. Taking a few moments to read this
manual will help to ensure that your vehicle is protected at all times.
NOTE:
The system has the ability to beep the vehicle's horn, sound a siren, or both. Where
a beep or chirp is mentioned, consider either or both may sound.
ARMING THE SYSTEM : ( ACTIVE )
1. Turn the ignition key off, exit the vehicle, and close all doors.
2. Press and release the Lock button on the keychain transmitter.
3. The siren and or horn will beep one time, the parking lamps will flash one time,
and the red dash mounted LED will begin to slowly flash, indicating that the
system is ARMED.
If the siren/horn sounds 3 chirps, then you have left a door, trunk, or hood lid ajar.
Simply close the opened entry point to provide full protection. If the siren "chirped"
three times, sometime after arming, the exclusive delayed dome light learn circuit
has been programmed and the system detected a open entry point after the
learned delay expired. Again, closing the hood, trunk, or doors will correct the
problem and you do not need to disarm the system to make the correction. If the
siren/horn did not sound when arming, then the chirps have been turned off, and
you should refer to the section titled “ ELIMINATING THE ARM / DISARM CHIRPS “
in this manual.
4. Any time the door lock switch in the vehicle is used to lock the doors while
the ignition key is turned off, the system will immediately arm. To lock the doors
after entering the vehicle, make sure the ignition key is switched on first.
Turning the ignition key on first will stop the system from arming.
ARMING THE SYSTEM : ( PASSIVE )
1. Turn the ignition key off, exit the vehicle, and close all doors.
2. The dash mounted LED will begin to flash rapidly, indicating that the system
1
128-7777
1 of 8
is automatically ( passively ) arming. As an added convenience, the 30 second
automatic passive arming will not begin until all doors are closed, allowing passengersto exit the vehicle at their convenience.
3. In 30 seconds, you will hear a single short chip from the siren, and the vehicle’s
parking lamps will flash one time, indicating that the system has ARMED. At this
time, the red dash mounted LED will begin to flash slowly, providing a visual
indication that the system is fully armed.
4. It is possible to program the system, that when the alarm is allowed to
automatically passive arm, there will be a 15 second delay after a door is opened
before thealarm will sound. However, if the system is programmed for instant
trigger there will be no delay. Check with your installer for the setting of this feature.
IMPORTANT! When the system is programmed for passive arming, the system will always arm, even when the keychain transmitter has not
been used to lock the doors.
When you leave the vehicle, and a door has been left opened, the system will
arm after 10 minutes. If you plan to vacuum the car, or if service work is being
performed, either leave the key in the ignition and switched to the on position,
or put the system into valet mode. If you do not do this, the system will arm in
10 minutes, and you will probably inadvertently trip the alarm.
PROTECTION WHILE THE SYSTEM IS ARMED :
1. Opening any door, hood, or trunk will cause the alarm to immediately sound. The
alarm will continue to sound for 30 seconds, then stop and automatically re - arm
the vehicle. If the potential thief left a door opened, the alarm will sound for five more
30 second cycles, then re - arm and ignore the opened door zone.
2. Whenever the system is armed, the red dash mounted LED indicator will
slowlyflash. This serves as a visual deterrent to the potential thief. The LED
is a very low current bulb, and will not cause the vehicle’s battery to drain, even
when the vehicle is left unattended for extended periods.
3. Whenever the system is triggered, the vehicle’s parking lights will flash for the
30second alarm cycle, attracting added visual attention to the vehicle.
4. Whenever the system is armed, the vehicle’s starter will be disabled. The
vehicle will not start.
DISARMING THE SYSTEM :
1. As you approach the vehicle, press and release the unlock button on the keychain
transmitter.
2. The siren and or horn will beep two times, the parking lamps will flash two
times, and the red dash mounted LED will turn off, indicating that the
system is DISARMED. If the optional entry illumination feature has been
2
128-7777
2 of 8
installed, the vehicle’s interior lights will turn on for 30 seconds, or until the
ignition key is turned on.
NOTE: If your system has been programmed for “ passive arming “, then it will
begin to re-arm immediately after disarming. This is indicated by a
rapid flashing of the red dash mounted LED Opening one of the
vehicle’s doors will suspend the passive arming process until all doors
have been closed, or until the ignition key has been turned on.
INTRUSION WARNING SIGNALS :
The system will inform you if an intrusion attempt has occurred while you were away
from the vehicle. If an intrusion attempt has occurred, the siren and or horn will beep
four times when the system is disarmed. The vehicle’s parking lights will also flash
three times to indicate an intrusion has occurred.
Enter the vehicle and observe the dash mounted LED for further information.
1. If the LED is flashing one time...pause...one time...pause...etc., then an
intrusion attempt was made to a voltage sensing, light activated entry point, or
to an optional sensor that has been connected to zone 1.
2. If the LED is flashing two times...pause...two times...pause...etc., then an
intrusion attempt was made to the hood or trunk, or to an optional sensor that
has been connected to zone 2.
3. If the LED is flashing three times...pause...three times...pause...etc., then an
intrusion attempt was made through one of the vehicle’s doors.
These intrusion warning indicators are stored in the system’s memory, and will
only be erased when the ignition key is turned to the “ on “ position.
OPERATING THE EMERGENCY PANIC:
The buttons on your keychain transmitter will allow you to immediately activate the
alarm in emergency situations. To use the remote panic switch;
1. Press the unlock, then lock, then unlock buttons on your keychain transmitter within
3 seconds. The alarm will immediately sound, and continue to sound for 30 seconds.
2. To stop the alarm before the 30 second cycle has expired, simply press and
release the unlock button on your keychain transmitter.
USING THE VALET SWITCH :
The valet switch allows you to temporarily bypass all alarm functions, eliminating the
need to hand your transmitter to parking attendants or garage mechanics. When the
system is in valet mode, all alarm functions are bypassed, however the remote panic
feature and remote door locks will remain operational. To use the valet mode, the
system must first be disarmed either by using your keychain transmitter, or
by activating your personalized manual override code.
3
128-7777
3 of 8
Loading...