Audiovox PRO 9232S User Manual
Model PRO 9232S
OWNER’S MANUAL
KEYLESS ENTRY ALARM UPGRADE MODULE
Congratulations on your purchase of the PRO 9232S automotive Keyless Entry
Upgrade Alarm System. The PRO 9232S is a state -of -the-art auto security system
that is designed to automatically arm and disarm when it receives a command from
your existing Factory Keyless Entry Transmitter. Taking a few moments to read this
manual will help to ensure that your vehicle is protected at all times.
ARMING THE SYSTEM: (ACTIVE)
1. Turn the ignition key off, exit the vehicle, and close all doors.
2. Press and release the Lock button on the keychain transmitter.
3. The siren and or horn will beep one time, the parking lamps will flash one
time, and the red dash mounted LED will begin to slowly flash, indicating
that the system is ARMED.
NOTE: If the unit beeps three times when arming, then one of the entry
points ( hood, trunk, or doors ) has been left opened. Closing the
hood, trunk, or door will correct the problem, and the system will
emit a single chirp to confirm that the problem has been corrected.
Additionally, if illuminated entry is a feature of the Factory Keyless
Entry system, the alarm may chirp 3 times every time the system is
armed, and chirp one additional time when the interior light turns off
to confirm that all trigger zones are fully operational.
Any time the door lock switch in the vehicle is used to lock the doors while
4.
the ignition key is turned off, the system will immediately arm. To lock the
doors after entering the vehicle,
first. Turning the ignition key on first will stop the system from arming.
ARMING THE SYSTEM: (PASSIVE)
1. Turn the ignition key off, exit the vehicle, and close all doors.
2. The dash-mounted LED will begin to flash rapidly, indicating that the
system is automatically ( passively ) arming. As an added convenience,
the 30 second automatic passive arming will not begin until all doors are
closed, allowing passengers to exit the vehicle at their convenience.
make sure the ignition key is switched on
3. In 30 seconds, you will hear a single short chip from the siren, and the
vehicle’s parking lamps will flash one time, indicating that the system has
ARMED. At this time, the red dash mountedLED will begin to flash
slowly, providing a visual indication that the system is fully armed.
4. It is possible to program the system, that when the alarm is allowed to
automatically passive arm, there will be a 15-second delay after a door is
opened before the alarm will sound. However, if the system is pro
grammed for instant trigger there will be no delay. Check with your
installer for the setting of this feature.
IMPORTANT !
When the system is programmed for passive arming, the
system will always arm, even when the keychain transmitter
has not been used to lock the doors. When you leave the
vehicle, and a door has been left opened, the system will
arm after 10 minutes. If you plan to vacuum the car, or if
service work is being performed, either leave the key in the
ignition and switched to the on position, or put the system
into valet mode. If you do not do this, the system will arm
in 10 minutes, and you will probably inadvertently trip the
alarm.
PROTECTION WHILE THE SYSTEM IS ARMED:
1. Opening any door, hood, or trunk will cause the alarm to immediately sound. The alarm will continue to sound for 30 seconds, then
stop and automatically re - arm the vehicle. If the potential thief left
a door opened, the alarm will sound for five more 30 second cycles,
then re-arm and ignore the opened door zone.
2. Whenever the system is armed, the red dash mounted LED indicator will
slowly flash. This serves as a visual deterrent to the potential thief. The
LED is a very low current bulb, and will not cause the vehicle’s battery to
drain, even when the vehicle is left unattended for extended periods.
3. Whenever the system is triggered, the vehicle’s parking lights will flash
for the 30 second alarm cycle, attracting added visual attention to the
vehicle.
4. Whenever the system is armed, the vehicle’s starter will be disabled.
The vehicle will not start.
5. With shock sensor installed, any strong impact to the vehicle’s glass
wil l cause the alarm to trigger for the full 30 second alarm cycle.
6. With 2 stage shock sensor installed, any mild impact to the vehicle's
glass will cause the alarm to sound a short series of warning tones.
DISARMING THE SYSTEM:
1. As you approach the vehicle, press and release the unlock button on the
keychain transmitter.
2. The siren and or horn will beep two times, the parking lamps will flash two
times, and the red dash mounted LED will turn off, indicating that the
system is DISARMED. If the optional entry illumination feature has been
installed, the vehicle’s interior lights will turn on for 30 seconds,
or until the ignition key is turned on.
NOTE: If your system has been programmed for “ passive arming “, then it
will begin to re-arm immediately after disarming. This is indicated by
a rapid flashing of the red dash mounted LED Opening one of the
vehicle’s doors will suspend the passive arming process until all
doors have been closed, or until the ignition key has been turned on.
INTRUSION WARNING SIGNALS:
The system will inform you if an intrusion attempt has occurred while you were
away from the vehicle. If an intrusion attempt has occurred, the siren and or horn
will beep four times when the system is disarmed. The vehicle’s parking lights will
also flash three times to indicate an intrusion has occurred.
Enter the vehicle and observe the dash mounted LED for further informa
1. If the LED is flashing one time...pause...one time...pause...etc., then an
intrusion attempt was made to a voltage sensing, light activated entry
point, or to an optional sensor that has
2. If the LED is flashing two times...pause...two times...pause...etc., then an
intrusion attempt was made to the hood or trunk, or to an optional sensor
that has been connected to zone 2.
3. If the LED is flashing three times...pause...three times...pause...etc.,
then an intrusion attempt was made through one of the vehicle’s doors.
These intrusion warning indicators are stored in the system’s memory, and will
only be erased when the ignition key is turned to the “ on “ position.
been connected to zone 1.
tion.
OPERATING THE EMERGENCY PANIC:
The buttons on your keychain transmitter will allow you to immediately activate the
alarm in emergency situations. To use the remote panic switch:
1. Press the unlock, then lock, then unlock buttons on your keychain
transmitter within 3 seconds. The alarm will immediately sound, and
continue to sound for 30 seconds.
2. To stop the alarm before the 30 second cycle has expired, simply press
and release the unlock button on your keychain transmitter.
Loading...