Audiovox PRO 2032 User Manual

Model PRO 2032

OWNER’S MANUAL

KEYLESS ENTRY ALARM UPGRADE MODULE

Congratulations on your purchase of the PRO 2032 automotive Keyless Entry
Upgrade Alarm System. This system is a state-of-the-art auto security system that
is designed to automatically arm and disarm when it receives a command from your
existing Factory Keyless Entry Transmitter. Taking a few moments to read this
manual will help to ensure that your vehicle is protected at all times.

NOTE: This unit has the capability to operate an optional siren, the vehicle horn, or

both. Where referenced (the siren will chirp) the siren may chirp, the horn
may beep or both may occur.

1. Turn the ignition key off, exit the vehicle and close all doors.

2. Press and release the Lock button on the keychain transmitter.

3. The siren will chirp one time, the parking lamps will flash one time, and the red
dash mounted LED will begin to slowly flash, indicating that the system is
ARMED.

NOTE: If the unit beeps three times when arming, then one of the entry points

4.

1. Turn the ignition key off, exit the vehicle, and close all doors.

2. The dash mounted LED will begin to flash rapidly, indicating that the system is

(hood, trunk, or doors) has been left opened. Closing the hood, trunk, or
door will correct the problem and the system will emit a single chirp to
confirm that the problem has been corrected. Additionally, if illuminated
entry is a feature of the Factory Keyless Entry system, the alarm may chirp
3 times every time the system is armed and chirp one additional time
when the interior light turns off to confirm that all trigger zones are fully
operational.

Any time the door lock switch in the vehicle is used to lock the doors while the

ignition key is turned off, the system will immediately arm. To lock the doors after
entering the vehicle,
ignition key on first will stop the system from arming.

automatically ( passively ) arming. As an added convenience, the 30 second
automatic passive arming will not begin until all doors are closed, allowing
passengers to exit the vehicle at their convenience.

ARMING THE SYSTEM: ( ACTIVE )

make sure the ignition key is switched on first. Turning the

ARMING THE SYSTEM: ( PASSIVE )

1

Released 7-23-01.

128-6132

1 OF 8

3. In 30 seconds, you will hear a single short chip from the siren and the vehicle’s
parking lamps will flash one time, indicating that the system has ARMED. At
this time, the red dash mounted LED will begin to flash slowly, providing a visual
indication that the system is fully armed.

IMPORTANT!

will always arm, even when the keychain transmitter has not been used to lock
the doors.
When you leave the vehicle and a door has been left opened, the system will arm
after 10 minutes. If you plan to vacuum the car, or if service work is being
performed, either leave the key in the ignition and switched to the on position,
or put the system into valet mode. If you do not do this, the system will arm in
10 minutes and you will probably inadvertently trip the alarm.

1. Opening any door, hood, or trunk will cause the alarm to immediately sound. The
alarm will continue to sound for 30 seconds, then stop and automatically re-arm
the vehicle. If the potential thief left a door opened, the alarm will sound for five
more 30 second cycles, then re-arm and ignore the opened door zone.

2. Whenever the system is armed, the red dash mounted LED indicator will slowly
flash. This serves as a visual deterrent to the potential thief. The LED is a very
low current bulb and will not cause the vehicle’s battery to drain, even when the
vehicle is left unattended for extended periods.

3. Whenever the system is triggered, the vehicle’s parking lights will flash for the
30 second alarm cycle, attracting added visual attention to the vehicle.

4. Whenever the system is armed, the vehicle’s starter will be disabled. The vehicle
will not start.

1. As you approach the vehicle, press and release the unlock button on the
keychain transmitter.

2. The siren will chirp two times, the parking lamps will flashtwo times and the
red dash mounted LED will turn off, indicating that the system is DISARMED.
If the optional entry illumination feature has been installed, the vehicle’s interior
lights will turn on for 30 seconds, or until the ignition key is turned on.

NOTE: If your system has been programmed for " passive arming ", then it will

When the system is programmed for passive arming, the system

PROTECTION WHILE THE SYSTEM IS ARMED:

DISARMING THE SYSTEM:

begin to re-arm immediately after disarming. This is indicated by a rapid
flashing of the red dash mounted LED. Opening one of the vehicle’s
doors will suspend the passive arming process until all doors have been
closed, or until the ignition key has been turned on.

2

128-6132

2 OF 8

The system will inform you if an intrusion attempt has occurred while you were away
from the vehicle. If an intrusion attempt has occurred, the siren and or horn will beep
four times when the system is disarmed. The vehicle’s parking lights will also flash
three times to indicate an intrusion has occurred.
Enter the vehicle and observe the dash mounted LED for further information.

1. If the LED is flashing one time...pause...one time...pause...etc., then an intrusion
attempt was made to a voltage sensing, light activated entry point, or to an
optional sensor that has been connected to zone 1.

2. If the LED is flashing two times...pause...two times...pause...etc., then an
intrusion attempt was made to the hood or trunk, or to an optional sensor that
has been connected to zone 2.

3. If the LED is flashing three times...pause...three times...pause...etc., then an
intrusion attempt was made through one of the vehicle’s doors.

These intrusion warning indicators are stored in the system’s memory and will only
be erased when the ignition key is turned to the "on" position.

INTRUSION WARNING SIGNALS :

The buttons on your keychain transmitter will allow you to immediately activate the
alarm in emergency situations. To use the remote panic switch;

1. Press the unlock, then lock, then unlock buttons on your keychain transmitter
within 3 seconds. The alarm will immediately sound and continue to sound for
30 seconds.

2. To stop the alarm before the 30 second cycle has expired, simply press and
release the unlock button on your keychain transmitter.

The valet switch allows you to temporarily bypass all alarm functions, eliminating
the need to hand your transmitter to parking attendants or garage mechanics.
When the system is in valet mode, all alarm functions are bypassed, however the
remote panic feature and remote door locks will remain operational. To use the
valet mode, the system must first be disarmed either by using your keychain
transmitter, or by activating your personalized manual override code.

TO ENTER THE V ALET MODE:

1. Disarm the unit by use of the factory transmitter or by use of the manual override
sequence.

2. Turn the ignition switch to the "On" position.

3. Press and hold the valet/override pushbutton switch for 5 seconds. The LED
turns on, indicating valet mode has been successfully entered.

TO EXIT VALET:
With the ignition switch in the on position, press and release the valet/override
pushbutton switch one time. The LED turns off indicating the valet mode has
successfully been exited.

OPERATING THE EMERGENCY PANIC:

USING THE VALET SWITCH:

3

128-6132

3 OF 8