Audiovox PRO 2000 User Manual

Model PRO 2000

Short Manual

RF Programmable Features :

Feature Selection 1 Chirp 2 Chirps 3 Chirps 4 Chirps 5Chirps Default 1st DoorL/UL 1 Sec. 3.5 Sec. 1 Sec L, Dbl. U/L Dbl L, 1 Sec U/L Dbl L, Dbl U/L 1 Sec.

2nd Accy Lock Auto Lock On Auto Lock Off Off 3rd Accy. UL Auto UL Dr Auto UL All Auto UL Off O f f 4th Passive Locks Passive Active Active 5th Pass/Act Arm Passive Arm Active Arm Active 6th Voltage Sense On Off Off 7th Siren/Horn O/P Siren&Horn Siren Only Horn Only S&H 8th Horn Chirp 10ms 16ms 30ms 40ms 50ms 16ms 9th Override Method Custom Code Valet Valet 10th Two Step Unlock On Off Off 11th Chp. From Tx. On Off Off 12th Keyless Or Alarm Keyless Alarm Keyless

To program these selectable features;

First Then On 1 chirp = 1 second door locks

Second Press and release the valet switch 2 chirps = auto locks off

Third Press and release the valet switch 3 chirps = auto unlock off

Fourth Press and release the valet switch 2 chirps = active door locks

Fifth Press and release the valet switch 2 chirps = active arming

Sixth Press and release the valet switch 2 chirps = voltage sense off

Seventh Press and release the valet switch 1 chirp = siren and horn output

Eight Press and release the valet switch 2 chirps = horn chirp output 16mS

Ninth Press and release the valet switch 2 chirps = valet switch override operation

Tenth Press and release the valet switch 2 chirps = 2 step unlock off

Eleventh Press and release the valet switch 2 chirps = chirp delete from transmitter inactive

Twelfth Press and release the valet switch 1 chirp = keyless entry mode

Note: Once you enter the feature programming mode, do not allow more than 15 seconds to pass between steps, or the programming will be

terminated.

Note: This system allows the transmitter to be programmed for single button lock/unlock or separate button lock/unlock. The receiver is set up as

follows:

Action System Response Turn ignition on No response Press and release the valet switch 3 times 1 Chirp - LED 1 flash Within 3 seconds, turn ignition Off Short chirp, then long chirp

Press transmitter Lock button to change 2 chirps = 3.5 second door locks Press transmitter Lock button to change 3 chirps = 1 sec. lock, dbl 1 sec. unlock Press transmitter Lock button to change 4 chirps = 1 sec. unlock, dbl 1 sec. lock Press transmitter Lock button to change 5 chirps = dbl 1 sec. lock, dbl 1 sec. unlock

Press transmitter Lock button to change 1 chirp = auto locks on

Press transmitter Lock button to change 1 chirp = auto unlock drivers door only Press transmitter Lock button to change 2 chirps = auto unlock all doors

Press transmitter Lock button to change 1 chirp = passive door locks

Press transmitter Lock button to change 1 chirp = passive arming

Press transmitter Lock button to change 1 chirp = voltage sense on

Press transmitter Lock button to change 2 chirps = siren output only Press transmitter lock button to change 3 chirps = horn output only

Press transmitter Lock button to change 3 chirps = horn chirp output 30mS Press transmitter Lock button to change 4 chirp = horn chirp output 40 mS Press transmitter Lock button to change 5 chirps = horn chirp output 50mS Press transmitter Lock button to change 1 chirp = horn chirp output 10 mS

Press transmitter Lock button to change 1 chirp = custom code override operation

Press transmitter Lock button to change 1 chirp = 2 step unlock on

Press transmitter Lock button to change 1 chirp = chirp delete from transmitter active

Press transmitter Lock button to change 2 chirp = alarm mode Press and release the valet switch Exit program mode Turn ignition key off Exit program mode

or or

Channel #1 = Lock/Unlock/Unlock 2 & Panic (Unlock only if no button is programmed to Ch.2) Channel #2 = If Programmed, Unlock/Unlock 2 & Panic Channel #3 = Channel 3 & Alternate Channel 3 Channel #4 = Channel 4 Output Channel #5 = Channel 5 Output (If so Equipped)

Released 7-24-01.

128-6103

Front Page

During the program routine, if a transmitter button is programmed into receiver channel 2, then the unit will always have separate lock/unlock from that transmitter. If during the program sequence receiver channel 1 is programmed and receiver channel 2 is skipped over, as indicated in the transmitted program guide, then the unit will operate as a single button lock/unlock unit from that transmitter. It is possible to have one transmitter programmed for single button lock/unlock and one transmitter programmed for separate button lock/ unlock if the customer so desires. If you inadvertently incorrectly program the transmitter, please read the information on reprioritizing found in the transmitter programming guide.

128-6103

Back Page