INSTALLATION MANUAL
SEL
PWR
LOUD
CDC/
LUM
O
E
V
5
BAND
DISC
DISC
SEL
PCD-5
AUX
SCN
1
2
RPT
RPT
A-B
RDM
43
4x40 WATTS
PGM
5
1
2
TUNE
3
5
TRK
4
MEM
6
CLR
PCD - 5
AM/FM/MPX RADIO
WITH FOLD-DOWN
DETACHABLE FRONT PANEL,
5 - DISC COMPACT DISC PLAYER,
AND QUARTZ CLOCK
REL
AS/PS
T/F
INSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONS
This unit is designed for installation in cars, trucks, and vans with an existing radio opening. In many cases, a special installation kit will
be required to mount the radio to the dashboard. These kits are available at electronics supply stores and car stereo specialist shops.
Always check the kit application before purchasing to make sure the kit works with your vehicle. If you need a kit but cannot find it available, call
our toll-free “HELP” line (1-800-645-4994).
UNIVERSAL INSTALLATION PROCEDURE USING MOUNTING SLEEVE
1. Remove the detachable front panel to prevent damage to the face and/or controls; use the Release (REL)
button to allow the panel to fold down. Then withdraw the panel from the mounting plate. Slide the mounting sleeve
off of the chassis. If it is locked into position, use the removal tools (supplied) to disengage it.
2. Check the dashboard opening size by sliding the mounting sleeve into it. If the opening is not large enough, carefully
cut or file as necessary until the sleeve easily slides into the opening. Do not force the sleeve into the opening
or cause it to bend or bow. Check that there will be sufficient space behind the dashboard for the radio chassis.
3. Locate the series of bend tabs along the top, bottom, and sides of the mounting sleeve. With the sleeve
fully inserted into the dashboard opening, bend as many of the tabs outward as necessary so that the
sleeve is firmly secured to the dashboard.
4. Place the radio in front of the dashboard opening so that the wiring can be brought through the mounting
sleeve. Follow the wiring diagram carefully and make certain all connections of the wiring harness are
secure and insulated with wire nuts or electrical tape to insure proper operation of the unit. After completing
the wiring connections, attach the front panel and turn the unit on to confirm operation (ignition switch must
be “on”). If unit does not operate, re-check all wiring until problem is corrected. Once proper operation is
achieved, turn off the ignition switch and proceed with final mounting of the chassis.
5. Carefully slide the radio into the mounting sleeve making sure it is right-side-up until it is fully seated and
the spring clips lock it into place.
6. Attach one end of the perforated support strap (supplied) to the screw stud on the rear of the chassis using
the hex nut provided. Fasten the other end of the perforated strap to a secure part of the dashboard either
above or below the radio using the screw and hex nut provided. Bend the strap to position it as necessary.
CAUTION: The rear of the radio must be supported with the strap to prevent damage to the dashboard from
7. Re-attach the front panel to the chassis and test radio operation by referring to the Operating Instructions for
theunit.
the weight of the radio or improper operation due to vibration.
INSTALLATION USING KITS
1. If your vehicle requires the use of an installation kit to mount this radio, follow the instructions included with
the installation kit to attach the radio to the mounting plate supplied with the kit.
2. Wire and test the radio as described in Step 4 above.
3. Install the radio/mounting plate assembly to the sub-dashboard according to the instructions of the installation kit.
4. Attach the support strap to the radio and dashboard as described in Step 6 above.
5. Replace the dashboard trim panel.
ISO INSTALLATION PROCEDURE
This unit has threaded holes in the chassis side panels which may be used with the original factory mounting brackets of some Toyota,
Nissan, Mitsubishi, Isuzu, Hyundai and Honda vehicles to mount the radio to the dashboard. Please consult with your local car stereo
specialist shop for assistance on this type of installation.
1. Remove the existing factory radio from its dashboard or center console mounting. Save all hardware and
brackets as they will be used to mount the new radio.
2. Carefully un-snap the plastic frame from the front of the new radio chassis. Remove and discard the frame.
3. Remove the factory mounting brackets and hardware from the existing radio and attach them to the new radio.
CAUTION: DO NOT EXCEED M4 X 8 MM MAXIMUM SCREW SIZE.
4. Wire the new radio to the vehicle as per step 4 above.
5. Mount the new radio assembly to the dashboard or center console using the reverse procedure of step 1.
LONGER SCREWS MAY TOUCH AND DAMAGE COMPONENTS INSIDE THE CHASSIS.
-2-
TT
OLL-FREE INSTOLL-FREE INST
T
OLL-FREE INST
TT
OLL-FREE INSTOLL-FREE INST
The installation and wiring connections for this unit are so simple, we doubt you'll need our help, but, if you
do, we're here to help you. Just call our toll-free telephone assistance line at 1-800-645-4994 during the days
and hours shown (U.S.A. and Canada only).
ALLALL
ALL
ALLALL
AA
TT
ION ASSISTION ASSIST
A
T
ION ASSIST
AA
TT
ION ASSISTION ASSIST
AA
A
AA
NCENCE
NCE
NCENCE
DAY
MON. - FRI.
SATURDAY
SLEEVE
ADAPTER
HALF-SLEEVE
1
2
TIME ZONE
FASTEN THIS END TO SECURE
PART OF DASHBOARD
BOLT
(M4 X 8 MAX)
CENTRAL
7:30AM - 6PM
8AM - 4PM
FASTEN THIS END TO BOL T HOLE
IN REAR CENTER OF CHASSIS
SLEEVE
ADAPTER
(REF)
BEND TOP
TABS UPWARD
PACIFIC
5:30AM - 4PM
6AM - 2PM
UNIVERSAL INSTALLATION USING MOUNTING SLEEVEUNIVERSAL INSTALLATION USING MOUNTING SLEEVE
UNIVERSAL INSTALLATION USING MOUNTING SLEEVE
UNIVERSAL INSTALLATION USING MOUNTING SLEEVEUNIVERSAL INSTALLATION USING MOUNTING SLEEVE
PERFORATED
SUPPORT STRAP
DASHBOARD
MOUNTAIN
6:30AM - 5PM
7AM - 3PM
1. SLIDE RADIO INTO HALF-SLEEVE.
2. SECURE TO STRAP USING BOLT IF POSSIBLE.
3. REINSTALL ANY ITEMS YOU REMOVED FROM THE DASHBOARD.
EASTERN
8:30AM - 7PM
9AM - 5PM
BEND BOTTOM
TABS DOWNWARD
HALF-SLEEVE
(REF)
1. REMOVE TRIM RING FROM FRONT OF RADIO.
2. MOUNT FACTORY BRACKETS ON NEW RADIO
USING EXISTING SCREWS FROM OLD RADIO.
3. SLIDE RADIO AND FRAME INTO DASH OPENING
AND SECURE.
4. INSTALL DASH P ANELS PREVIOUSL Y REMOVED.
ISO-DIN FINAL INSTALLATION
-3-
RR
AA
DIO WIRINGDIO WIRING
R
A
DIO WIRING
RR
AA
DIO WIRINGDIO WIRING
REFER TO PAGE 5 FOR SPEAKER WIRING
-4-
SPESPE
AA
KK
SPE
SPESPE
REFER TO PAGE 4
FOR RADIO WIRING
ER WIRINGER WIRING
A
K
ER WIRING
AA
KK
ER WIRINGER WIRING
l NEVER COMBINE (BRIDGE) OUTPUTS FOR USE WITH 1 SPEAKER.
NEVER GROUND NEGATIVE SPEAKER LEADS TO CHASSIS GROUND.
l
l FAILURE TO WIRE EXACTLY AS SHOWN BELOW MAY CAUSE ELECTRICAL DAMAGE TO
THE RADIO.
WARNING!
-5-
© 2001 Audiovox Electronics Corp., Hauppauge, NY 11788 Printed in China
128-6160
6
Loading...