Audiovox P-965 User Manual

Page 1
INSTALLATION MANUAL
EQ
CLAS
POP
TRACK
SCAN RPTRND
P-965
AM/FM/MPX RADIO WITH MOTORIZED
SLIDE-DOWN DETACHABLE FRONT PANEL,
COMPACT DISC PLAYER,
CD CHANGER CONTROLS,
WIRELESS REMOTE CONTROL
AND QUARTZ CLOCK
Page 2
INSTALLATION INSTRUCTIONS
This unit is designed for installation in cars, trucks, and vans with an existing radio opening. In many cases, a special installation kit will be required to mount the radio to the dashboard. These kits are available at electronics supply stores and car stereo specialist shops. Always check the kit application before purchasing to make sure the kit works with your vehicle. If you need a kit but cannot find it available, call our toll-free “HELP” line at 1-800-645-4994.
UNIVERSAL INSTALLATION PROCEDURE USING MOUNTING SLEEVE
1. Activate panel fold-down, and remove the detachable front panel, if it is attached to the chassis, by grasping the release latch on the middle underside of the panel and pulling the panel assembly straight out. The mounting plate will return to the upright position within 3 seconds. Slide the mounting sleeve off of the chassis. If it is locked into position, use the removal tools (supplied) to disengage it.
2. Check the dashboard opening size by sliding the mounting sleeve into it. If the opening is not large enough, carefully cut or file as necessary until the sleeve easily slides into the opening. Do not force the sleeve into the opening or cause it to bend or bow. Check that there will be sufficient space behind the dashboard for the radio chassis.
3. Locate the series of bend tabs along the top, bottom, and sides of the mounting sleeve. With the sleeve fully inserted into the dashboard opening, bend as many of the tabs outward as necessary so that the sleeve is firmly secured to the dashboard.
4. Place the radio in front of the dashboard opening so that the wiring can be brought through the mounting sleeve. Follow the wiring diagram carefully and make certain all connections of the wiring harness are secure and insulated with wire nuts or electrical tape to insure proper operation of the unit. After completing the wiring connections, attach the front panel and turn the unit on to confirm operation (ignition switch must be “on”). If unit does not operate, re-check all wiring until problem is corrected. Once proper operation is achieved, turn off the ignition switch and proceed with final mounting of the chassis.
5. Carefully slide the radio into the mounting sleeve making sure it is right-side-up until it is fully seated and the spring clips lock it into place.
6. Attach one end of the perforated support strap (supplied) to the screw stud on the rear of the chassis using the hex nut provided. Fasten the other end of the perforated strap to a secure part of the dashboard either above or below the radio using the screw and hex nut provided. Bend the strap to position it as necessary.
CAUTION: The rear of the radio must be supported with the strap to prevent damage to the dashboard from the weight of
the radio or improper operation due to vibration.
7. Re-attach the front panel to the chassis and test radio operation by referring to the Operating Instructions for the unit.
INSTALLATION USING KITS
1. If your vehicle requires the use of an installation kit to mount this radio, follow the instructions included with the installation kit to attach the radio to the mounting plate supplied with the kit.
2. Wire and test the radio as described in Step 4 above.
3. Install the radio/mounting plate assembly to the sub-dashboard according to the instructions of the installation kit.
4. Attach the support strap to the radio and dashboard as described in Step 6 above.
5. Replace the dashboard trim panel.
ISO INSTALLATION PROCEDURE
This unit has threaded holes in the chassis side panels which may be used with the original factory mounting brackets of some Toyota, Nissan, Mitsubishi, Isuzu, Hyundai and Honda vehicles to mount the radio to the dashboard. Please consult with your local car stereo specialist shop for assistance on this type of installation.
1. Remove the existing factory radio from its dashboard or center console mounting. Save all hardware and brackets as they will be used to mount the new radio.
2. Carefully un-snap the plastic frame from the front of the new radio chassis. Remove and discard the frame.
3. Remove the factory mounting brackets and hardware from the existing radio and attach them to the new radio.
CAUTION: DO NOT EXCEED M5 X 8 MM MAXIMUM SCREW SIZE. LONGER SCREWS MAY TOUCH AND DAMAGE
COMPONENTS INSIDE THE CHASSIS.
4. Wire the new radio to the vehicle as per step 4 above.
5. Mount the new radio assembly to the dashboard or center console using the reverse procedure of step 1.
-2-
Page 3
TOLL-FREE INSTALLATION ASSISTANCETOLL-FREE INSTALLATION ASSISTANCE
TOLL-FREE INSTALLATION ASSISTANCE
TOLL-FREE INSTALLATION ASSISTANCETOLL-FREE INSTALLATION ASSISTANCE
The installation and wiring connections for this unit are so simple, we doubt you'll need our help, but, if you do, we're here to help you. Just call our toll-free telephone assistance line at 1-800-645-4994 during the days and hours shown (U.S.A. and Canada only).
TIME ZONE
DAY
MON. - FRI. SATURDAY
SCREW (5MM)
NUT (5MM)
PACIFIC
5:30AM - 4PM 6AM - 2PM
NUT (5MM)
PERFORATED STRAP
FASTEN THIS END TO SCREW STUD ON REAR OF CHASSIS
MOUNTING SLEEVE
MOUNTAIN
6:30AM - 5PM
7AM - 3PM
UNIVERSAL INSTALLATION USING MOUNTING SLEEVEUNIVERSAL INSTALLATION USING MOUNTING SLEEVE
UNIVERSAL INSTALLATION USING MOUNTING SLEEVE
UNIVERSAL INSTALLATION USING MOUNTING SLEEVEUNIVERSAL INSTALLATION USING MOUNTING SLEEVE
EXISTING DASH OPENING FILE EDGES TO FIT IF NECESSARY - DO NOT OVERFILE NOTE: IF DASH IS SOLID, USE REAR SIDE (WITHOUT THE LIP) OF MOUNTING SLEEVE AS A TEMPLATE & CUT OPENING
SCREW STUD
RADIO
CENTRAL EASTERN
7:30AM - 6PM
8AM - 4PM
BEND TOP TABS UPWARD
8:30AM - 7PM
9AM - 5PM
BEND BOTTOM TABS DOWNWARD
FASTEN THIS END TO SECURE PART OF DASHBOARD. DRILL HOLE IF NECESSARY.
FOR PROPER OPERATION OF THE CD PLAYER, THE CHASSIS MUST BE MOUNTED WITHIN 20° OF HORIZONTAL. MAKE SURE THE UNIT IS MOUNTED WITHIN THIS LIMITATION.
SIDE VIEW
OF
CHASSIS
REMOVE THE PLASTIC FRAME FROM THE FRONT OF THE CHASSIS BY CAREFULLY UN-SNAPPING IT.
CAUTION:
20° MAX.
FRONT PANEL
UN-SNAP AT 2 PLACES EACH ON TOP AND BOTTOM
PLASTIC FRAME
REMOVAL TOOLS
ISO INSTALLATIONISO INSTALLATION
ISO INSTALLATION
ISO INSTALLATIONISO INSTALLATION
MAXIMUM SCREW
FACTORY MOUNTING BRACKETS
SIZE
M5 x 8
FOLD-DOWN DETACHABLE FRONT PANEL
TYPICAL INSTALLATION
MAXIMUM SCREW
SIZE
M5 x 8
-3-
Page 4
RADIO WIRINGRADIO WIRING
RADIO WIRING
RADIO WIRINGRADIO WIRING
REFER TO PAGE 5 FOR SPEAKER WIRING
ANTENNA
EXISTING ANTENNA CABLE
AUTOMATIC ANTENNA
BLUE
IMPORTANT
THE BLUE WIRE CAN BE USED TO REMOTELY ACTI­VATE AN AUTOMATIC ANTENNA OR AN EXTERNAL AMPLIFIER (SEE ANTENNA OR AMPLIFIER MANUAL)
RED (0.5 AMP. FUSE)
SCREW
BLACK
YELLOW (15 AMP. FUSE)
METAL PART OF DASH (DRILL HOLE IF NECESSARY)
FUSEBLOCK
“RADIO” FUSE +12V ACCESSORY
CAR BATTERY
ANTENNA LEAD ON REAR OF RADIO
FILTER/FUSE BOX
YELLOW WIRE MUST BE CONNECTED AS SHOWN OR RADIO WILL NOT OP­ERATE PROPERLY
CONTAINS: ONE 0.5 AMP FUSE ONE 15 AMP FUSE
IMPORTANT
4-PIN PLUGS
9 PIN PLUG (SEE PAGE 5 FOR SPEAKER WIRING)
CD CHANGER LEAD ON REAR OF RADIO (SEE PAGE 5)
POSITIVE (+) TERMINAL 12 VOLT BATTERY
-4-
Page 5
SPEAKER WIRINGSPEAKER WIRING
SPEAKER WIRING
SPEAKER WIRINGSPEAKER WIRING
REFER TO PAGE 4 FOR RADIO WIRING
RCA LINE OUT JACKS
FOR USE WITH
OPTIONAL EXTERNAL
AMPLIFIERS
LINE OUT (LEFT) = WHITE LINE OUT (RIGHT) = RED
SUB-LINE OUT
WARNING!
l THE AMPLIFIERS IN THIS RADIO ARE ONLY DESIGNED FOR USE WITH 4 SPEAKERS. l NEVER COMBINE (BRIDGE) OUTPUTS FOR USE WITH 2 SPEAKERS. l NEVER GROUND NEGATIVE SPEAKER LEADS TO CHASSIS GROUND. l FAILURE TO WIRE EXACTLY AS SHOWN BELOW MAY CAUSE ELECTRICAL
NOTE: THIS RADIO WILL CONTROL PRESTIGE CD CHANGER MODEL SP-11CDP AND MODEL SP6CDP. CHECK WITH YOUR PRESTIGE AUDIOVOX CAR STEREO SPECIALIST OR CALL 1-800-645-4994 FOR RECOMMENDATIONS OF OTHER MODELS THAT WILL WORK WITH YOUR RADIO.
RADIO
CD CHANGER LEAD ON REAR OF RADIO
OPTIONAL CD CHANGER
6
DIN CABLE (SUPPLIED WITH CD CHANGER)
COMPACT
REMOTE INPUT JACK FOR USE WITH EXTERNAL CD-PLAYER, CASSETTE PLAYER, OR MP3 PLAYBACK
LEFT FRONT SPEAKER
WHITE w/BLACK STRIPE
9-PIN PLUGS
WHITE
GREEN
GREEN w/BLACK STRIPE
VIOLET w/BLACK STRIPE
HELP!
4-PIN PLUGS
SEE PAGE 4 FOR RADIO WIRING
GRAY w/BLACK STRIPE
GRAY
VIOLET
RIGHT FRONT SPEAKER
1-800-645-49941-800-645-4994
1-800-645-4994
1-800-645-49941-800-645-4994
Monday - Friday Saturday
LEFT REAR SPEAKER RIGHT REAR SPEAKER
8:30am - 7:00pm Eastern 9:00am - 5:00pm Eastern
-5-
Page 6
© 2001 Audiovox Electronics Corp., Hauppauge, NY 11788 Printed in China
128-6028
Loading...