Audiovox MT 128-7902A User Manual

Page 1
CommanderMT System
installation guide
XMRVRFM002
Page 2
2
TT
able of Contentsable of Contents
T
able of Contents
TT
able of Contentsable of Contents
Table of Contents
Congratulations ..................................................................................................3
FCC Information .................................................................................................. 4
Cautions and Warnings ...................................................................................5
CommanderMT Receiver Kit Components ..............................................6
Installation/Wiring Precautions .................................................................... 7
Setting Up and Installing Your Kit ...............................................................8
Cabling Interconnections ......................................................................8
Interconnect Diagram .............................................................................9
Antenna Installation ............................................................................. 10
CommanderMT Display Controller Installation ....................... 13
Using the DIN Opening Trim Bezel............................................ 13
Preferred Location ....................................................................... 13
Locating the Display Controller ............................................ 14
Installing the Mini-Tuner........................................................... 15
Installing the Cradle and Interconnecting Cables ......... 15
Using the Snap-On Mounting Plate ......................................... 17
Connection Options ........................................................................ 18
FM Direct Wiring ........................................................................... 18
Low-Level Audio Output .......................................................... 19
Warranty ......................................................................................................... 20
Page 3
CongratulationsCongratulations
Congratulations
CongratulationsCongratulations
Thank you for purchasing the Audiovox CommanderMT XM System. You are one step closer to experiencing the latest innovation in XM Satellite Radio. XM® Satellite Radio will revolutionize your vehicle or in-home entertainment.
®
XM
features over 170 digital channels — The most commercial-free music, over 30 channels of news, sports, talk and entertainment, over 20 dedicated channels of XM industry with access to over 2 million titles!
®
XM
Satellite Radio service gives you the power to choose what you want to hear - wherever and whenever you want it. XM provider with over 4 million customers. Your Audiovox CommanderMT XM® Satellite Radio System consists of acces­sory Vehicle Kit components required for your specific installation needs.
Required subscription for service sold separately.
Installation costs and other fees and taxes may apply, including a one-time activation fee. All fees and programming subject to change. College sports games subject to availability. Subscriptions subject to Customer Agreement included with the XM Welcome Kit and available at available in the 48 contiguous United States.
®
Instant Traffic & Weather, and the deepest play-list in the
®
is America’s #1 Satellite Radio
www.xmradio.com. Only
®
Satellite Radio
3
Congratulations
®
© 2007 XM rights reserved. All other trademarks are the property of their respective owners.
®
Satellite Radio Inc. XM® is a trademark of XM® Satellite Radio. All
Page 4
4
FCC InformationFCC Information
FCC Information
FCC InformationFCC Information
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful in
FCC Information
terference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. How ever, there is no guarantee that interference will not occur in a particular instal lation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: — Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver. — Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
The user is cautioned that changes or modifications not expressly approved by XM Satellite Radio, Inc. can void the user’s authority to operate this device.
Please note that the cables and antenna wire that has been supplied with your car installation kit are supplied with permanently attached ferrite beads. It is the responsibility of the user to use the cable and antenna wire with the ferrite beads.
By adhering to these warnings and safety considerations, stated in the manual and by XM®, accidents.
®
Page 5
Cautions and WarningsCautions and Warnings
Cautions and Warnings
Cautions and WarningsCautions and Warnings
1. Do not install the CommanderMT Display Controller in a position that hinders your view through the windshield, or obstructs viewing of the dashboard indicators and displays.
2. Do not install the Display Controller where it may obstruct the operation or deployment of safety devices, such as airbags, etc.
3. Do not allow operation of the unit to detract from safe driving prac­tices; remember that you are responsible as the vehicle operator to adhere to all safe driving and traffic regulations.
4. By adhering to these warnings and safety considerations, serious accidents and/or personal injury can be avoided.
5
Cautions and Warnings
Page 6
6
CommanderCommander
Commander
CommanderCommander
CommanderMT
Display Controller
CommanderMT Receiver Components
FM Direct Adapter
XM Car
Antenna
MT Receiver Kit ComponentsMT Receiver Kit Components
MT Receiver Kit Components
MT Receiver Kit ComponentsMT Receiver Kit Components
^
^
menu
p/d
0
987654321
Remote Control
DIN Opening
Trim Bezel
Snap-On
Mounting
Plate
XM
Mini-Tuner
Interconnect
Cradle
12 Vdc
Power Cable
Page 7
Installation/Wiring PrecautionsInstallation/Wiring Precautions
Installation/Wiring Precautions
Installation/Wiring PrecautionsInstallation/Wiring Precautions
1. To prevent a short-circuit, be sure to turn off the ignition and remove the negative (-) battery cable prior to installation. Connect power wires last.
2. Do not install the CommanderMT Display Controller in loca­tions exposed to direct sunlight, or in areas subject to extreme temperatures, or damage could occur.
3. Incorrect installation may cause damage to the system. Mount the system components using the suggested methods recom­mended in this manual.
4. Be careful not to crimp or twist the vehicle wiring.
5. Use only the 12 Volt DC Power Cable supplied. Use of an alternative power source could damage the CommanderMT System compo­nents or vehicle wiring.
6. Locate the CommanderMT Display Controller in an area of the vehicle where it will not obstruct the driver’s operation of the vehicle and where it will not pose a risk to driver or passengers in the event of an emergency stop.
7
Installation/Wiring Precautjions
Page 8
8
Setting Up and Installing YSetting Up and Installing Y
Setting Up and Installing Y
Setting Up and Installing YSetting Up and Installing Y
NOTE: The XM® signal can be received and processed virtually
anywhere as long as there are no obvious satellite signal obstructions such as nearby buildings, high terrain, parking
garages or tunnels.
Cabling Interconnections
1. Cabling Interconnections
You can begin to enjoy XM® Satellite Radio as soon as the CommanderMT System Vehicle Kit installation is complete. Set up yourAudiovox CommanderMT System using the following installation instructions, or enlist the help of a professional installer:
WARNING:Professional installation is recommended. Failure to
properly follow all installation instructions may result in personal injury or damage to your CommanderMT System components, your vehicle, or your vehicle Audio/Video (A/V) system.
our Kitour Kit
our Kit
our Kitour Kit
Page 9
Interconnect DiagramInterconnect Diagram
Interconnect Diagram
Interconnect DiagramInterconnect Diagram
Interconnect
Cradle with XM
Mini-Tuner
DIN Opening
Trim Bezel
CommanderMT
Display Controller
FM Direct Adapter
XM Antenna
Power Cable
with 2A
In-line Fuse
T o FM Antenna
To FM Radio
9
Cabling Interconnections
Page 10
10
2.Important!
It is very important to make your power connection to a source that only supplies 12V when the vehicle key is in the accessory or ignition ON position. A connection to a 12V source that is always on, regardless of the key position, can lead to a battery drain if the CommanderMT System is left on when you leave your vehicle.
ACCESSORY POSITION
Important/Antenna Installation
Ignition Switch Accessory/On-Off Positions
3. Antenna Installation
Where to locate
Best reception is achieved with the antenna mounted on a flat
portion of a metal vehicle roof with at least 12” x 12” of surface area and a minimum of 6” from a window or sunroof.
If the vehicle has roof racks or skid ribs, it may be necessary to mount the antenna off-center.
If the venicle roof does not provide sufficient metal surface area, then the antenna can be mounted on the metal trunk lid. It is recommended that it be mounted at least several inches from the rear window to ensure adequate clearance.
NO ACCESSORY POSITION
Page 11
Caution: 1.Do not install the antenna inside the vehicle passen-
ger compartment. Mounting the antenna in the passen­ger compartment either on the from dashboard, or on the rear window deck area will cause reception issues and must be avoided.
2. Mounting the antenna on a non-metalic surface will also result in severe degradation in reception.
If an appropriate antenna mounting location cannot be identified, contact your local retailer installation department for additional guidance.
Cable routing
Once you have mounted the antenna in the correct location, plan
how to route the cable from this location to the receiver Inteconnect Cradle, avoiding blocked passages and any obstruc­tions that could kink, crimp, twist or chafe the cable. If the cable will come into contact with a rough metal opening, use a rubber grommet to prevent damage.
For antenna mounting locations at the front or middle of the roof, the cable can be routed down along the door jamb and into the car. In some cars, the cable may be brought into the vehicle through the grommet in the door jamb which carries the power window and power door lock wires. If the cable does not fit easily through this grommet, do not try to force it through. Instead, route the cable under the weather seal near the bottom of the door.
11
Antenna Installation
Page 12
12
Antenna Installation
For antenna mounting locations at the rear of the roof, the antenna
cable can be routed into the vehicle through the trunk. Always route the cable under the weather seal near the lowest part of the trunk to reduce possible water leaks.
Use pre-existing wiring channels created by the vehicle manufac-
turer whenever possible.
Tools required
The antenna contains a powerful magnet that will secure it to a
metal roof under normal driving conditions. No additional tools should be necessary to mount the antenna.
Antenna Mounting Methods
Page 13
4. CommanderMT Display Controller Installation
Be sure to locate your Display Controller below the top of the dash in your vehicle to keep the unit within easy reach while driving. Choosing a lower location in your installation should also make it easier to manage the cables and achieve a more desirable appear­ance when the installation is completed. See illustration below and be sure to locate your Display Controller within the outlined shaded areas.
13
Display Controller Installation
Page 14
14
The CommanderMT Display Controller can be installed using the DIN opening trim bezel or a snap-on mounting plate as shown below. The trim bezel permits in-dash or center console mounting, while the mounting plate can be used with optional
custom brackets, such as swivel or vent mounts.
a. Using the DIN Opening Trim Bezel
Display Controller Installation
Preferred location
Your CommanderMT Receiver Kit includes a DIN opening trim bezel for mounting the display controller into an existing dash­board or console opening.
Using the DIN Opening
Trim Bezel
Page 15
b. Using the Snap-On Mounting Plate
To attach the CommanderMT cradle to optional mounting devices that are readily available at retail, attach the snap-on mounting plate to the rear of the CommanderMT Display Controller as shown below.
Examples of Optional
Aftermarket Mounting
Alternatives
15
Display Controller Installation
Page 16
16
5. Connection Options
The CommanderMT System provides an audio output signal in two ways:
a. FM Direct Wiring - The FM direct adapter supplies a hard-
Connection Options
wired FM output, provided the FM Frequency option of the XM Mini-Tuner is turned on and tuned to an unused FM frequency.
XM Antenna
Interconnect
Cradle with XM
Mini-Tuner
FM Direct Adapter
T o FM Antenna
To FM Radio
Page 17
b. Low-Level Audio Output - For vehicle radio head units with
auxiliary audio inputs, the audio signal can be routed through an optional audio cable (Part No. SAT-RCA) and applied to the auxiliary inputs of a radio or entertainment system. In this case, to listen to the audio. the System must be disabled (FM Frequency Off), as indicated in the CommanderMT System User Guide.
ROTATE DIAL TO SELECT
Receiver FM modulator option
17
Connection Options
FM frequency
Interconnect Cradle with XM
Mini-Tuner
To Vehicle Radio
Low Level Audio
Inputs
Off
Optional Audio Cable SAT -RCA
Page 18
18
6. Cable Routing and Component Installation
Once you have established power connections, Display Controller and antenna placement, and audio connection, route all cables to the location where you will mount the Interconnect Cradle. When you have plugged the power and antenna jacks into the cradle, re-use the cable twist ties that were provided with the power and car antenna cables and always be sure to gather, bundle, twist-tie, and secure any excess cable remain­ing after determining the best location for your satellite radio installation.
XM MINI-TUNER
Cable Routing and Component Installation
CRADLE
COVER LOCKING TABS
PLASTIC RETAINING COVER
CRADLE WITH COVER IN PLACE
ATT ACH VELCRO PAD OR DOUBLE­SIDED TAPE HERE
Page 19
a. Installing the Cradle and Interconnecting Cables - Locate the
Interconnect Cradle in a readily accessible location, such as the glove compartment, console compartment, or under the dashboard, so that the XM Mini-Tuner can be removed or replaced. Note also that the cradle must be situated close enough to comply with the CommanderMT Display Controller cable and Power Cable lengths (6’).
b. Installing the Mini-Tuner - Install the XM Mini-Tuner in the
cradle by inserting the tuner into the cradle slot until the cradle and tuner connectors mate together. You will feel the tuner connector click into place. Fold the plastic retainer cover over the cradle and press down until the cradle tabs lock into the the cover side holes. The XM Mini-Tuner is now secured in place in the cradle.
Good installation practices should be observed when mounting any component to avoid vibration, movement or rattling after installation. When routing cables, avoid blocked passages and any obstructions that could kink, crimp, twist, or chafe the cables. Components should be secured in place using methods such as Velcro, double-sided foam tape, etc.
19
Cable Routing and Component Installation
Page 20
20
12 MONTH LIMITED WARRANTY
Warranty
FM Satellite Radio
XMRVRFM002
AUDIOVOX ELECTRONICS CORPORATION (the Company) warrants to the original retail purchaser of this product that should, under normal use and conditions, be proven defective in material or workmanship within 12 months from the date of original purchase, such defect(s) will be repaired or replaced with new or reconditioned product (at the Company's option) without charge for parts and repair labor.
To obtain repair or replacement within the terms of this warranty, the product is to be delivered with proof of warranty coverage (e.g. dated bill of sale), specification of defect(s), transportation prepaid, to an approved warranty station or the Company at the address shown below.
This Warranty does not extend to the elimination of externally generated static or noise, to costs incurred for installation, removal or reinstallation of the product, or to damage to speakers, accessories, or electrical systems. Warranty does not apply to malfunction of satellite transmis­sions, repeater signals or audio systems or to damage caused by poor installation of included components such as magnetic roof mount an­tenna, disiplay control unit or receiver docking station.
This Warranty does not apply to any product in the opinion of the Company that has been damaged through alteration, improper installation, mis­handling, misuse, neglect, accident, or by rimoval or defacement of the factory serial number number/bar code label(s). THE EXTENT OF THE
Page 21
COMPANY'S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN NO EVENT, SHALL THE COMPANY'S LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT.
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. ANY ACTION FOR BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, MUST BE BROUGHT WITHIN 24 MONTHS FROM DATE OF ORIGINAL PURCHASE. IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EX­PRESS OR IMPLIED, WHATSOEVER. No person or representative is authorized to assume for the Company any liability other than expressed herein in connection with the sale of this product.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damage so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights and you may also have other rights which vary from state to state.
U.S.A.: Audiovox Electronics Corporation
Canada: CALL 1-800-645-4994 for Location of Warranty Station Serving Your Area
11788 (1-800-645-4994)

150 Marcus Blvd

 
Hauppauge, New York
 
21
Warranty
128-7902A
Page 22
Audiovox Electronics Corporation 150 Marcus Blvd. Hauppauge, New York 11788 U.S.A. 1 800 645 4994
www.audiovox.com
XM name and related logos are trademarks of XM Satellite Radio Inc.
Printed on Recycled Paper
©2007 Audiovox Electronics Corporation. All rights reserved.
XMRVRFM002
Loading...