Audiovox MMD7HRPKG Owner's Manual

MMD7HRPKG

Two Specific Vehicle Headrests

With 7” LCD Monitors and Built-In

DVD Player for Rear Seat Entertainment

Operation Manual

128-8281

IMPORTANT

Installation of headrest products require careful planning and preparation. Be extremely careful of seats that have airbags built into them. Keep wiring away from any air bag wiring (usually identified by yellow connectors and yellow wire jackets). Damage to air bag wiring can result in personal injury to vehicle occupants. If you have any questions regarding wire routing or installation in a vehicle, please contact Audiovox Technical Support at 1-800-225-6074.

When connecting power and ground in a mobile video installation, insure that the ACC wire is fused at the point where it is connected to the vehicle ACC wiring. Failure to do so can result in damage to the vehicle if a short circuit develops between the vehicle connection point and the mobile video product.

An LCD panel and/or video monitor may be installed in a motor vehicle and visible to the driver if the LCD panel or video monitor is used for vehicle information, system control, rear or side observation or navigation. If the LCD panel or video monitor is used for television reception, video or DVD play, the LCD panel or video monitor must be installed so that these features will only function when the vehicle is in “park” or when the vehicle’s parking brake is applied.

An LCD panel or video monitor used for television reception, video or DVD play that operates when the vehicle is in gear or when the parking is not applied must be installed to the rear of the driver’s seat where it will not be visible, directly or indirectly, to the operator of the motor vehicle.

Licensed under one or more of the following patents: Patent NOS. 7245,274 and 6,899,365

MMD7HRPKG

The MMD7HRPKG contains two headrests. The master unit M1 (MMD7HRM) has a built-in DVD player and the satellite unit M2 (MMD7HRS) has a monitor that is used to either watch the DVD movie that is playing in the master unit or a video source plugged into the

AUX jack on the front of the unit. The full function remote control can operate either unit by selecting M1 or M2 on the remote. Each monitor has an AUX input and wired headphone jack on the bottom right hand side of the screen.

Quick Start Guide

1. Turn on the M1 (MMD7HRM) monitor, tilt the screen forward using the center tab at the top of the screen.

2. Insert a DVD, CD or MP3 disc into the slot, disc label toward driver.

3. The disc will start playing.

4. Tilt the monitor to a comfortable viewing position (the headrest itself can be tilted forward to help achieve a comfortable viewing position).

5. Optional wireless headphone has a CH A/CH B switch. When sitting in front of the M1 screen, use the CH A switch setting. When sitting in front of the M2 screen, use the CH B switch setting. Set the headphone to the proper channel and press the Power On/Off switch. The power indicator will light up red. Turn the volume down to its lowest setting before putting them on your head.

6. When the DVD menu appears on the M1 monitor, select the menu item using the cursor keys and press the Enter or Play button.

7. Turn on the MMD7HRS monitor using the power button on the front of the screen or remote control.

8. Tilt the screen to a comfortable viewing position (the headrest itself can be tilted forward to help achieve a comfortable viewing

position).

9. Select AV1 using the source button on the front panel or remote control to view program material on the M1 monitor or select AUX

for M2 monitor.

NOTE: To operate the MMD7HRM screen, press M1 on the remote control.

To operate the MMD7HRS screen, press M2 on the remote control.

CONTROLS AND INDICATORS DIAGRAM

Control Function Descriptions for MMD7HRM and MMD7HRS Monitor

MMD7HRM / MMD7HRS Panel Control

1. DVD disc insertion slot

2. EJECT Button – Press this button to eject the disc.

3. Power Indicator LED

4. POWER Button – Press to turn the unit ON/OFF.

5. SCREEN MODE Button– Press this button to select between

Wide(16:9), Normal(4:3) aspect ratio or screen off (display OFF).

6. PLAY Button – Press this button to start playback.

7. SOURCE Button– Press this button to select between DVD and

AUX.

8. STOP Button – Press this button to stop playback.

9. IR Transmitter LEDS

10. Wired Headphone Jack

11. AUX Input Jack (use with supplied AV adaptor)

NOTE : 1, 2, 6 & 8 function for MMD7HRM only.

MMD7HRM

MMD7HRS

3 4 5

EJECT

8 10 11

3 4 5

10 11

MMD7HRPKG SYSTEM OVERVIEW

1) The MMD7HRPKG SYSTEM is a versatile audio / video system with built-in DVD player (MMD7HRM only) which includes two monitors, that can accept an Audio / Video input and independent AUX input. A separate audio output is provided for connecting an optional FM Modulator to the vehicle's radio.

2) The M1 Monitor (MMD7HRM) is comprised of a 7" TFT LCD monitor with built-in DVD player that allows the user to select from the DVD, and the AUX source. The M1 monitor has a built-in infrared audio transmitter (CH A) for use with the optional two-channel wireless headphones (CH A).

3) The M2 Monitor (MMD7HRS) is comprised of a 7" TFT LCD monitor that allows the user to select from the DVD source in M1 (AV1) or AUX source.

The M2 monitor has a built-in infrared audio transmitter (CH B) for use with the optional two channel wireless headphones (CH B).

4) The monitors will show all of the functions with the comprehensive OSD.

5) The optional two-channel wireless Headphone sets have an A-B switch that allow the user to select the audio from either M1 (MMD7HRM, CH A) or M2 (MMD7HRS,CH B).

6) Using different IR codes, the M1 Monitor will only respond to the remote control unit when the Monitor Select (M1) button on remote control is pressed. The M2 Monitor will only respond to the Remote Control unit when the Monitor Select (M2) button on remote control is pressed.

7) The wired headphones allow the user to listen to audio from the system.

8) The M1 (MMD7HRM) and M2 (MMD7HRS) Monitor will accept an audio / video input through the 1/8” jack located on the front of the unit. The audio / video device could be a video game system, video camera, or other input device.

MMD7HRS MMD7HRM

AUX IN

MMD7HRS MMD7HRM

HEADPHONE

JACK

9) Pivot the screen until a comfortable viewing angle reached. The internal lock limits the screen to a maximum adjustment of 30 degrees from closed position, the headrest itself can be tilted forward to help achieve a comfortable viewing position.

Inner Ring

Internal Lock

Closed Position

10) Insert disc

Disc Label

Insert disc

MMD7HRPKG: MMD7HRM Monitor only.

30 degrees

11) Eject disc

Eject disc

MMD7HRPKG: MMD7HRM Monitor only.

REMOTE CONTROL OPERATION

CR2025

Initial Use

When purchased the remote control has a battery installed with a Pull Tab to prevent battery discharge. Remove the Pull Tab before attempting to use the remote.

Battery Replacement

1. Remove the battery holder.

2. Insert the battery into the battery holder and insert the

battery holder into the remote. Be sure to observe the correct polarity.

3. Align the battery holder with the remote control and push

until the holder clicks.

2 3

7 8

24 23

19 18

17 16 15

+ 16 hidden pages