Audiovox MMD11 Installation Manual

MMD11

11" OVERHEAD LCD MONITOR

WITH DVD PLAYER

Installation Guide

Important Notice

An LCD panel and/or video monitor may be installed in a motor vehicle and visible to the driver if the LCD panel or video monitor is used for vehicle information, system control, rear or side observation or navigation. If the LCD panel or video monitor is used for television reception, video or DVD play, the LCD panel or video monitor must be installed so that these features will only function when the vehicle is in “park” or when the vehicle’s parking brake is applied.

An LCD panel or video monitor used for television reception, video or DVD play that operates when the vehicle is in gear or when the parking brake is not applied must be installed to the rear of the driver ’s seat where it will not be visible, directly or indirectly, to the operator of the motor vehicle.

Important Note

The MMD11 incorporates two new features:

1) A wireless FM Modulator

2) Snap on Covers with matching Trim Rings (Shale and Pewter).Select the color that matches the interior trim.

Please be advised that the wireless FM modulator will perform well in most applications. However, in certain applications the quality of the wireless signal may be less than optimal, resulting in static or strong local station bleed thru. If this is the case, an optional relay box is available. The Audiovox part number is SIRSWB and it plugs into the 1/8" jack located next to the FM antenna on the side of the chassis. This relay box is installed between the vehicle antenna and the car radio to provide the best possible FM reception of the DVD player audio. When the SIRSWB is installed it is recommended that the wireless FM antenna that is plugged into the printed circuit board next to the

3.5mm jack be unplugged.

Licensed under one or more of the following patents, Patent NOS. 5,775,762 and 5,927,784

MATERIALS INCLUDED IN THIS PACKAGE:

1) 11" TFT LCD Overhead Monitor With DVD Player – (1pc)

2) 12 Pin Power / Signal harness (P/N 112-3483) – (1pc)

3) 2 Pin Power Wire Harness with choke (P/N 112B3143) – (1pc)

4) 9 Pin ~ 3 RCA Jack Pigtail (P/N 112-3682) – (1pc)

5) Hardware Package Screws ISO 3 x 6mm Long – (10pcs) #8 x 3/8" Self Drilling Screws – (4pcs) M5 Screws – (4pcs)

6) Remote Control (P/N 136-4196) – (1pc)

7) Universal Mounting Bracket (P/N 108-3930) – (1pc)

8) Pry Tool (P/N 100-2424) – (1pc)

9) Trim Ring - Shale (P/N 102-4244) – (1pc)

- Pewter (P/N 102-4245) – (1pc)

10) Snap On Cover (Shroud) - Shale (P/N 102-4248) – (1pc)

- Pewter (P/N 102-4249) – (1pc)

Optional Accessories

11) Wireless Headphones (P/N MMIRHSNL) – (2pc)

12) SIRSWB Relay Box (P/N 112C3159) – (1pc)

TOOLS RE QUIRED:

#2 Phillips Screwdri ver #1 Phillips Screwdri ver Utility or Razor Knife or Shears Wire Strippers Upholstery hook tool (for removal of panels as necessary) Electrical Tape Masking Tape Multimeter (to verify 12 volt DC an d continuity: Do not use a test light or logic probe) Marker pen – to mark headline r Scribe (to mark tr im ring if used) Misc. electrical connectors (to connect to vehicle power sour ce). Requirements will vary from vehicle to ve hicle) DVD Movie (to veri fy system operation after inst allation)

(Optional)

Installing The Snap On Covers

1. 2. 3.

Housing

Snap On Cover

(Shroud)

1 Pewter, 1 Shale

Pry Tool

Place the pod on a soft surface to avoid damaging the plastic.

Installing The Shroud

catch catch

(A)

Begin by hooking area “A” (above) over the dome light and slide the cover over the pod. The cover will snap in place.

Removing The Snap On Cover (Shroud) From The Housing

Work on a soft surface to avoid damaging the plastic. Insert the supplied pry tool between the Housing and Snap On Cover (Shroud), then press the pry tool to release the Snap On Cover (Shroud).

1 2 3

+ 8 hidden pages