Audiovox LCMR6CT User Manual

Rearview Mirror with 4.5" Color LCD with

Navigation/2 Camera inputs/Compass

And Outside Temperature Display

Model: LCMR6CT

Installation Manual

Features:

Rearview Mirror with 4.5” LCD Rearview Camera Input Interior View Camera Input Navigation Display Input NTSC /PAL Compatible Camera Input Compass Display Outside Temperature Display

Cautions!

The product is intended to assist in safe driving and to allow the driver to have a broader rearview while the vehicle is in reverse. You, as the driver, are solely responsible for the safe operation of your vehicle and the safety of your passengers according to the country and their local traffic regulations. Do not use any features of this system to the extent it distracts you from safe driving. Your first priority while driving should always be the safe operation of your vehicle. Audiovox Electronics Corporation cannot accept any responsibility whatsoever for accidents resulting from failure to observe these precautions or safety instructions.

1. This product utilizes high voltage. Any unauthorized modifications or damage to the products may result in electrical shock. Handle all components with care. Inspect regularly for damage to components and cabling.

2. You shall be responsible to ensure that the installation of this product does not void or affect the vehicle manufacturer’s warranty. Audiovox Electronics Corporation, or its branches are not liable in full or in part for improper installation resulting in loss or damage to your property, or for voiding all or part of the vehicle manufacturer’s warranty.

3. Do not apply excessive force to any of the components contained within this kit. Excessive force used before, during or after installation that results in a damaged or non-functional part shall void all warranties.

4. Please follow the procedure from this installation manual. Improper installation or modification of this product shall void all warranties.

TABLE OF CONTENTS

Cautions! 1

Preface 3

Packing list 3

1.Installation Instructions 4

2.Signal Inputs 7

3.Controls and Indicators 9

Specifications 12

Maintenance 13

Troubleshooting 14

Illustration of connections 15

Preface

This replacement mirror /monitor can display up to 3 different video

inputs. The inputs are Navigation, Rear observation camera and Interior

observation camera.

Not all rearview mirrors attach to the vehicle with the same style mount.

Please consult the application guide for the appropriate mounting bracket

for your vehicle or call Tech Service at 800-225-6074.

Packing list

The Rear view mirror Model LCMR6CT consists of the following items:

1. Rear View Mirror-1 2. Camera Cable-2

3. Control Box-1 4. Filter Box -1

5. Control Box Monitor Cable -1 6. Compass sensor –1

7. Temperature sensor -1 8. Tapping Screw –3

9. Connector-1 10. Wire cover -2

11. Double side adhesive tape –1

12. Compass &Temperature Monitor Cable –1

1. Installation Instructions

(1) Mount the mirror/monitor

a) Remove the original factory mirror. (Do not use excessive force when

removing factory mirror.) Check to make sure that the factory mirror mount you

remove matches the mirror mount on the replacement mirror. If it does not

match, consult the application guide or call Technical Service at 800-225-6074.

b) Slide the receiving bracket on the back of the new mirror stalk onto the

windshield mounting button. Move the bracket back and forth until completely

seated.

c) Tightly the T-20 mounting bracket screw.

(2) Navigation monitor connection (optional): Insert the connector from the

Audiovox navigation monitor cable into the receptacle at the backside of the

mirror/monitor. Route the rest of the monitor cable under the headliner, down the A

pillar to the Navigation computer.

(3) Control box connection:

mirror/monitor 8 pin cable. Route the cable under the headliner of the windshield then

down the A pillar behind the plastic shroud to the under dash area. Connect the 8-pin

cable to the control box 8 pin connector.

Connect the 8-pin extension cable to the rearview

(4) Installing the Temperature Sensor.

a) Select a suitable location for the Temperature sensor outside of the vehicle. The location should be in the nose area of the vehicle, between the front of the radiator and front bumper where there will be airflow. Keep the sensor as low as possible, and as far away from the radiator as possible.

b) Use the supplied screw to secure the temperature sensor to the selected location.

c) Route the temperature sensor cable towards the firewall, securing the cable where it doesn't interfere with moving parts.

d) Pass the terminals thought a grommet into the passenger compartment,

e) Route the wires up to and behind the A pillar, then under the headliner towards the Rearview mirror.

f) Insert the terminals into the two-pin connector until a snap is heard.

g) Connect the 6-pin Temperature/Compass Y cable to the rearview mirror/monitor cable.

h) Connect the 2-pin connector from the sensor to the mating end of the Temperature/ Compass Y cable.

(5) Installing the Compass sensor:

a ). Select a suitable mounting location for the compass sensor. The sensor must be mounted horizontally and with the Arrow pointing towards the front of the vehicle. Do not mount near a speaker or magnetic source. Under the dash top panel is a recommended location.

Figure 2

+ 11 hidden pages