Page 1
Page 2
1
FCC Compliance Statement
Note :
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment dose cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
- Consult the dealer or an experienced radio /television technician for help.
Notice 1 :
The changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
Notice 2 :
Shielded interface cables, if any, must be used in order to comply with the
emission limits.
DOC CLASS B NOTICE
This digital apparatus does not exceed Class limits for radio noise emission
for a digital apparatus as set out in the Radio Interference Regulations of the
Canadian Department of Communications.
INSTRUCTION
MAIN FEATURE 2
FRONT/BACK OF MONITOR 2,3
FUNCTION 3
INST ALLING
COMPONENTS 4
PRECAUTIONS IN INSTALLING 4
CONNECTING TO YOUR PC For 15" Only 5
CONNECTING TO YOUR PC For 17" Only
TV/VIDEO FUNCTION SETTING
PICTURE CONTROL 7
SOUND CONTROL 8
INSTALL 9
OSD 10
TELETEXT FUNCTION
TELETEXT (OPTION) 11,12
PC FUNCTION SETTING
OSD CONTROL 13
CONTRAST / BRIGHTNESS /ADJUST CONTROL 14,15
OTHERS
POWER SAVING MODE(S) 16
STANDARD SIGNAL TIME CHART 17
PRECAUTIONS 18
TROUBLE SHOOTING 19
REMOTE CONTROL 20
SPECIFICATIONS For 15" Only
SPECIFICATIONS For 17" Only
21
22
6
Page 3
2
BACK OF MONITOR
Ventilator(Caution! )
Do not block the ventilator
Hole for wall hanging
Detachable Base
Detachable for other equipments
(VESA ARM) and wall hanging use.
Connector to External Functions
Connects signals with external
equipments and PCs. (TV/VIDEO
)
MAIN FEATURES
LCD Panel
Menu
Control Button
Select
Power Switch
Uesd in turning on/off the screen.
The power light shows regular and
safe mode functions with colors.
Speaker
Detachable Base
3
Thank you for purchasing our high resolution TFT LCD monitor.
We recommend that you thoroughly read through this user's guide
before using the product.
It is also recommended to safely store the guide in times of
immediate need in the course of using the product.
FRONT OF MONITOR
FUNCTIONS
Although regular monitors for PCs use CDT as a medium for display, the TFT
LCD monitor is a Flat Panel Display based on digital technology, and was
originally used only for laptops PCs. Now it is used for desktops and laptops
alike, opening a world of conveniences and quality to those ardent PC users.
The following functions are provided in our products.
1. Convenient and easy to handle Control Button.
2. From PC function to TV/VIDEO functions.
3. Remote Control.
4. A slim and space reducing monitor.
5. Monitor transferable for wall hanging.
6. Industrial robot and VESA install able.
7. Liberal angle control.(+30
8. Low energy consumption.
9. Scarcely influences surrounding objects, with no harmful electronic waves,
noise, heat or magnetic activities.
~ -5 )
Page 4
12V DC S-VHS ( Y Pb pr )
VIDEO
PC
L R
AUDIO
H-
PHONE
S/T- IN ANTENNA
Connect to 100V~240V capacity outlets. (Free Voltage)
COMPONENTS
After discarding the package and wrapping of the LCD TV,
check for the following components in the box.
Components
LCD TV Power Adapter User s Guide Signal Cable
Power Cable Audio Cable Remote Controller
Battery (AA) 1.5V x 2
CONNECTING TO YOUR PC for 15" Only
12V DC Jack
PC 15 pin Jack
S-VHS Jack
Terminal Cable Y (Composite or Component)
Terminal Cable Pb (Component)
Teminal Cable Pr (Component)
Audio Cable L . R
Head Phone Jack
PC Audio Jack
TV Antenna Jack
PRECAUTIONS IN INSTALLING
Install on safe ground. : There's a possibility of damage of the product
or harming people.
Always cover the product or keep in a well ventilated place. : There is danger
of fire and also for safe maintenance.
Do not put anything containing water, medicine, small metal material, or heavy
objects on the product. : Danger of fire, electrocution, and damage
to the product.
Do not expose the product to direct sun light. : The screen will not maintain
clarity and may cause damage to the eye.
Do not install in damp, dusty, or wet places. : Danger of fire and electrocution.
Do not put candles, cigarettes, or other objects with excessive heat. : Danger
of fire.
Do not install any external connections, only connecting cords and
adapter included in the box. : Damage and fire may occur.
4
1. Connect to 12V DC with the adapter included in the box to 100V~240V
outlet.
2. Connect signal cable to PC. "Check Signal Cable"will appear on the
monitor if improperly connected. In case of using Macintosh, use the
exclusive adapter.
3. Connect to S-VHS Terminal of VCR, DVD,Camcorder.(optional)
4. Connect to Terminal of composite or Y-Terminal of component.
5. Connect to Pb-Terminal of component.
6. Connect to Pr-Terminal of component.
7.Connect to input terminals L, R that need Audio output.(DVD, VCR or
CAMCORDER)
8. Connect headphones to the connecting terminal.
9. Connect to PC Audio output.
10 . Connect to antenna or CATV connecting cable to the 'Antenna' terminal.
5
Page 5
CONNECTING TO YOUR PC for 17" Only
CONNECTING TO YOUR PC for 17" Only
1 : 12V DC Jack
2 : PC 15 pin Jack
3 : Head Phone Jack, PC Audio Jack
4 : TV Antenna Jack
5 : SCART
6 : S-VHS
7 : DVD/S-VHS Audio Jack L, R
8 : Terminal Cable Pr(Composite or Component)
9 : Terminal Cable Pb(Component)
10: Terminal Cable Y (Component)
11: Input Audio Jack L, R
12: Input Video Jack
13: Output Audio Jack L, R
14: Output Video Jack
12V DC PC
S/T
H-
IN ANTENA
Phone
TV/ VIDEO FUNCTION SETTING
Picture
Controlling Screen Contrast
Menu Picture Contrast Select
Control with Menu
You can control the contrast of the images or letter on the screen.
Controlling Screen Brightness
Menu Picture Brightness Select
Control with Menu
You can control the brightness of the screen.
Controlling Screen Color
1 2 3 4
SCART S-VHS R L Pr Pb Y R L VIDEO R L TV
AUDIO
AUDIO
IN
AUDIO
OUT
Menu Picture Color Select
Control with Menu
You can control the color of the screen.
Controlling Screen Sharpness
Menu Picture Sharpness Select
5 6 7 8 9 10 11 12 13 14
1. Connect to 12V DC with the adapter included in the box to 100V~240V
outlet.
2. Connect to signal cable to PC. "Check Signal Cable" will appear on the
monitor if improperly connected. In case of using Macintosh, use the
exclusive adapter.
3. Connect to headphones to the connecting terminal and PC Audio output.
4. Connect to antenna or CATV connecting cable to the 'Antenna' terminal.
5. Connect to SCART
If you connect the SCART, you must remove the RCA(COMPOSITE).
6. Connect to S-VHS Terminal of VCR, DVD, Camcorder.(Optional)
7. Connect to input Audio Terminals L,R of Component
8. Connect to Pr-Terminal of component.
9. Connect to Pb-Terminal of component.
10. Connect to Terminal of composite or Y-Terminal of component.
6
11. Connect to Input Audio Terminals L,R of Composite
12. Connect to Input Video Terminal of Composite
13. Connect to Output Audio Terminas L,R of TV
14. Connect to Output Video Terminal of TV
Control with Menu
You can select the sharpness of the screen.
Controlling Screen Tint(only NTSC)
Menu Picture Tint Select
Control with Menu
You can select the tint of the screen.
7
Page 6
Sound
Adjust Volume
S
M
e
nu
C
ontro
You can adjust volume of this screen.
l wit
h
S
ound
V
olume
M
e
nu
Adjust Balance
M
e
nu
C
ontro
You can adjust the Balance of this screen.
l wit
h
S
ound
M
B
alance
e
nu
Adjust Bass
M
e
nu
C
ontro
You can adjust the Bass of this screen.
l wit
h
S
ound
B
a
ss
M
e
nu
Adjust Treble
M
e
nu
C
ontro
You can adjust the Treble of this screen.
l wit
h
S
ound
T
reble
M
e
nu
elec
S
elec
S
elec
t
S
elec
Install
Auto search
M
e
nu
I
nstal
A
t
You can search channels automatically
uto search
TV System(PAL Only)
M
e
nu
TV
S
yste
mSelec
C
ontro
l wit
h
t
You can choose the TV System(PAL SECAM).
M
TV Sound(PAL Only)
M
e
nu
TV
S
ound
C
ontro
l wit
h
You can choose the TV Sound(BG DK I).
M
Manual tune
M
e
nu
I
nstallManua
C
ontro
l wit
h
You can change channel range positively or nagatively.
M
Fine Tune
M
e
nu
I
t
C
ontro
You can change range of tuner positively or negatively( 0.05Mhz)
l wit
nstallFine
h
M
Store to
M
e
nu
I
nstallStor
C
ontro
l wit
h
You can store the channel(P0 P99).
M
Skip
M
e
nu
I
nstallSkip
C
ontro
l wit
h
You can skip the channel(Yes No).
M
e
S
e
e
e
e
nu
elec
nu
e
nu
nu
e t
nu
nu
T
un
S
t
l tune
e
o
elec
t
t
8
9
Page 7
OSD (On Screen Display)
Vertical position of OSD
M
e
nu
OSDV P
C
ontro
l wit
h
You can adjust vertical position of OSD.
ositionSelec
M
e
nu
t
Horizontal position of OSD
M
e
nu
OSD H
C
ontro
l wit
h
You can adjust horizontal position of OSD.
P
osition
M
S
elec
t
e
nu
Halftone of OSD
M
e
nu
OSD
H
C
ontro
l wit
h
You can adjust halftone
alftoneSelec
M
e
nu
t
Input
TV or changing to another mode
M
e
nu
You can change input mode
(TV COMPOSITE S-VHS COMPONENT PC)
INPUT
S
elec
t
C
ontro
l wit
h
TELETEXT(Option)
SWITCHING TELETEXT ON/OFF
Press the TELETEXT button ( ). The index page viewed last will appear.
Press the TELETEXT button to return to the TV mode.
COLOR BUTTONS IN TOP/FLOF TELETEXT
A red,green, yellow and blue field is shown at the buttom of the screen.
If TOP or FLOF teletext(FASTEXT) is transmitted by the station, pressing
the corresponding color button on the remote controller, you can select
the desired page easily.
SELECTING PAGES
The NUMBER button 0...9 are used to enter a page number.
The selected page number appears at the top of the screen and the page
appears after a short time.
The UP/DOWN buttons increase or decrease the current page number by 1.
INDEX PAGE
You can switch directly to the program preview(with TOP text)
or the overview page of the station you are currently viewing by
pressing the INDEX( ) button. .
M
e
nu
PAGE HOLD
several sub pages can be combined under a page number and are scrolled
at an interval determined by the television station.
The presence of sub pages is indicated by, Y example, 3/6beneath the
time, which means that you are looking at the 3rd page of a total of 6pages.
If you want to look at a subpage for a longer period of time, press the
HOLD( )button.
The contents of the subpage shown are kept on the screen and no longer
updated or switched to other subpages. The HOLD symbol ( ) will be
displayed on the top left hand side instead of the page no..
Pressing the HOLD button again, the current subpage will appear.
10
12
11
Page 8
CALLING UP SUBPAGE DIRECTLY
The NUMBER button 0...9 are used to enter a page number.
The selected page number appears at the top of the screen and the page
appears after a short time.
The UP/DOWN buttons increase or decrease the current page number by 1.
WATCHING TELEVISION DURING TELETEXT MODE
Some pages are continually updated, for example, stock market reports,
sports announcements, and the latest news.
If you want to watch television and stay informed at the same time, press
CANCEL( )button.
The regular program is still visible and the telext symbol( )appears at
the top of the screen.
Pressing the CANCEL button again, the teletext page appears with the
update information.
REVEAL ANSWER
This function can be used on certain pages to reveal the solution of riddles.
Press the REVEAL button( ) to reveal a hidden answer and press again
to hide it.
DOUBLING CHARACTER SIZE
Repeatedly pressing the SIZE button( ) doubles the character size in the
following order: Upper half of the page-> Lower half of the page-> Return to
normal size.
PC FUNCTION SETTING
Information
Information of the screen
Menu Information Select
Control with Menu
You can see the information of the screen.
Input Source
TV or changing to another mode
Menu INPUT Select
Control with Menu
You can change input mode.
(TV - Composite - S-VHS - Component - PC)
OSD Control
Vertical Position of OSD
Menu OSD Control V Position Select
Control with Menu
You can adjust vertical position of OSD.
Horizontal Position of OSD
Menu OSD Control H Position Select
Control with Menu
You can adjust horizontal position of OSD.
12
Halftone of OSD
Menu
Control with Menu
You can adjust halftone of OSD.
OSD Control Halftone
Select
12
13
Page 9
Contrast
To clarify the screen
Menu Picture Contrast Select
Control with Menu
You can control the contrast of the images or letter on the screen
Clock Adjust
Menu
Control with Menu
You can adjust the clock.
Adjust Clock Adj.
Select
Brightness
To control brightness of the screen
Menu Picture Brightness Select
Control with Menu
You can control the brightness of the screen.
Adjust
Vertical Position
Menu Adjust V Po. Select
Control with Menu
You can adjust th vertical position of the screen.
Horizontal Position
Menu Adjust H P. Select
Control with Menu
You can adjust the horizontal position of the screen.
Phase Adjust
Menu
Control with Menu
You can adjust the phase.
Adjust
Phase Adj. Select
Auto Adjust
Menu
Control with Menu
You can adjust position of the screen automatically.
Adjust
Auto Adj. Select
Reset
Menu
Control with Menu
You can reset the screen.
Adjust Reset.
Select
14
15
Page 10
POWER SAVING MODE(S)
STANDARD SIGNAL TIMING CHART
If your computer system features a display power management function,
the Monitor enters into the power saving modes as follows.
When it is used with a computer system equipped with DPMS(VESA) this
Monitor provides an EnergyStar compliant function. If your computer
does not feature display power management, please source an optional
DPMS software program.
Power saving modes greatly reduce power consumption when the
computer is temporarily not in use. Simply press any key or mouse
button to return the Monitor display to normal operation.
Normal
Operation
H-Sync Active
V-Sync
Video
LED Color
Power
Consumption
Active
Active
Green
35 Watts
Less Than
Orange/Green
Blinking(1sec)
Power Saving function EPA
stand-by suspend Power Off
Inactive
Active
Blanked
8 Watts
Less Than
Active
Inactive
Blanked
Orange/Green
Blinking(0.5sec)
8 Watts
Less Than
Inactive
Inactive
Blanked
Orange
5 Watts
Less Than
If the signals conveyed from the computer match the following
standard signals, the screen automatically controls the signals.
Conversely, if the signals do not match,the screen will not appear or
only the power light would activate. Therefore it is important that you
first set as the following, with reference to the Video Card Guide.
18
19
20
21
22
1152x864
1152x864
1152x864
1152x864
1280x1024
54.5
63.8
65.8
68.5
64.9
60.0
70.0
72.0
75.0
60.0
90..000
96..600
96..600
98..000
108..000
16
17
Page 11
19 18
PRECAUTIONS
The below precautions should be carefully followed for the effective function
of the product and safety of users.
Do not use damaged plugs
or worn out outlets.
(Danger of electrocution)
Do not expose the product
to severe impacts.
(This could occur damage)
Do not try to disassemble, repair,
renovate the product without
expert assistance.
(Contact the service for parts
needing repair)
In weather conditions of thunder
and/or lightening, or when you will
not be using the product for a long
period of time, leave the plug out
of the outlet. (Danger of electrocution)
Do not try to bend the cord or put it
under heavy objects.
(Danger of electrocution, fire)
Do not leave the product in damp
or wet places as there is danger
when the product is exposed to water
or metal. (Danger of electrocution)
Other Precautions
In cleaning the product take out the plug from the outlet, wipe with
a soft and clean cloth then with water. Never use benzene,
alcohol or other cleaners. (Contact the service center or a store near
you for static controllers and cleaners. The LCD polarizing plate may
peel off or the product may decolorize, dissolve, or crack.
TROUBLE SHOOTING
When failure or problems occur, refer to the following. For further assistance,
contact our customer support centers.
The power dose not
turn on
"Check signal cable"
sign appears
appears on the screen.
The screen looks like
it is melting
The screen trembles
A shadow appears
on the screen
The screen is too
bright
The color of the
screen appears as if
there is a shadow.
White does not
to look like white
The screen is not
in place
There is no sound
The volume is too low
The sound is dull
The TV won
The power light is
orange or flickers
The screen is blurry
t turn on
Check whether the plug is in place and try to
reconnect it. (refer to pg5,pg6)
Check if the signal cable is properly connected to
the computer or video card and try to reconnect it
(refer to pg4)
Set the resolution and frequency compatible to
the monitor.(refer to pg18)
Check the connection of the monitor and the
signal cable of the computer.
Check if the resolution and frequency of the
computer or the video card is set to accommodate
the monitor and then reset the screen according
to the present mode of the monitor menu and
the standard signal timing chart.
Try to control the brightness or contrast of the
screen.(refer to pg 14)
Go to the OSD color control menu, the user mode
and control the door.(refer to pg10)
Recontrol image setting
Check the connecting cable. (refer to pg4, pg8)
Control with the up and down buttons
(refer to pg8)
Control with the up and down buttons
(refer to pg8)
Check if the antenna is connected and control
and control the mode with the TV.
Check if the computer is on safe mode. Press
on the PC keyboard or move the mouse.
The screen will appear.
Control the screen
(refer to pg 7)
s frequency and clarity.
Page 12
REMOTE CONTROL
TV mode TELETEXT mode
1 2 3
4 5 6
7 8 9
100 0
R G Y C
TV AV PC MENU
RECALL
SLEEP
AUDIO
SPECIFICATIONS For 15" Only
Category Specification
LCD Screen Size 15 inch (diagonal length)
(PANEL) Visible Screen size 304.1(H) X 228.1(V)
Frequency Horizontal Frequency 31 ~ 60 KHz(Auto Set)
Color Display Display color 16.2M Color
Input Signal Video Signal Analog 0.714Vp_p POSITIVE(75 ohm)
TV TV Color System PAL , SECAM , NTSC(option)
Sound Sound Output 2W + 2W ( 1KHz MOD 80%)
Power/Voltage Voltage Use Flow 100~240V, 50/60Hz DC 12V/3A
Energy Regular Energy
Consumption Consumption
Movement Temperature 0'C ~ 40'C
Conditions Humidity 10% ~ 85%
Size Excluding Base 380(W) X 58(D) X 336(H)
Weight Net 5Kg (11 Ibs)
Features Channel auto programming
Jack & TV ANT Input
Terminals Video In RCA jack
The above specifications can be changed without prior notice for quality
improvement.
Pixel Range 0.297(H) X 0.297(V)
Type A-si TFT LCD(liquid crystal display)
Visual Angle Upper 55'/lower 65' , left 70'/right 70'
Vertical Frequency 56 ~ 75 Hz (Auto Set)
Channel memory 100 Channel Memory -- PAL SYSTEM
Reciving Channel
Video Input Color PAL/SECAM/NTSC
Safe Mode
Consumption
Including Base 380(W) X 163(D) X 384(H)
Gross 7kg (15.4 Ibs)
Full function remote control
Composite video Input
S-VHS video Input
Component Input
PC sound Input
Audio In RCA jack
4-Pin Mini Din jack
15-Pin Mini D-Sub
181ch [113ch CATV] -- NTSC SYSTEM
Maximum 30W
Less then 5W
20
21
Page 13
SPECIFICATIONS For 17" Only
Category Specification
LCD Screen Size 17 inch (diagonal length)
(PANEL) Visible Screen size 337.0(H) X 270.0(V)
Frequency Horizontal Frequency
Color Display Display color 16.2M Color
Input Signal Video Signal Analog 0.714Vp_p POSITIVE(75 ohm)
TV TV Color System PAL , SECAM , NTSC(option)
Sound Sound Output 2W + 2W ( 1KHz MOD 80%)
Power/Voltage Voltage Use Flow 100~240V, 50/60Hz DC 12V/3A
Energy Regular Energy
Consumption Consumption
Movement Temperature 0'C ~ 40'C
Conditions Humidity 10% ~ 85%
Size Excluding Base 413(W) X 134(D) X 425(H)
Weight Net 7Kg (11 Ibs)
Features Channel auto programming
Jack & TV ANT Input
Terminals Video In RCA jack
The above specifications can be changed without prior notice for quality
improvement.
Pixel Range 0.264(H) X 0.264(V)
Type A-si TFT LCD(liquid crystal display)
Visual Angle Upper 80'/lower 80' , left 80'/right 80'
Vertical Frequency 56 ~ 75 Hz (Auto Set)
Channel memory 100 Channel Memory -- PAL SYSTEM
Reciving Channel
Video Input Color PAL/SECAM/NTSC
Safe Mode
Consumption
Including Base 492(W) X 240(D) X 492(H)
Gross 9kg (15.4 Ibs)
Full function remote control
Composite video Input
S-VHS video Input
Component Input
PC sound Input
Audio In RCA jack
4-Pin Mini Din jack
15-Pin Mini D-Sub
31 ~ 60 KHz(Auto Set)
181ch [113ch CATV] -- NTSC SYSTEM
Maximum 35W
Less then 5W
22
Loading...