Audiovox LCM-5600 Owner's Manual

LCM-5600

5.6" Active Matrix LCD Monitor

Owners Manual

EXPLANATION OF GRAPHIC SYMBOLS

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL

DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE

The lightning flash with the arrowhead within
a triangle is intended to alert tell the user
that parts inside the product are capable of
producing an electric shock .

The exclamation point within a triangle
i s intended to alert the user that important
operating and servicing instructions are
being provided.

WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK

HAZARD, DO NOT EXPOSE THIS PRODUCT
TO RAIN OR MOISTURE.

2

SPECIFICATIONS

1. Type: Color Liquid Crystal Display (LCD)
Monitor

2. Display Screen Size: 5.6 inches
(114.2 x 83mm) ( W x H )
Element : TFT LCD
Format : 480 (W) x 234 (H) dot
Total 112,320 dot

3. Back Light: Cold Cathode Fluorescent Lamp

4. Power Source: +12 VDC

5. Power Consumption: 11W

6. Connection Terminals: Video/Audio Input Jacks (RCA)
External Power Jack (DC IN 12V)

IR Jack

7. Operating Temperature: 32°F - 104°F
(0°C - 40°C)

8. Storage Temperature: -4°F - 176°F
(-20°C - +80°C)

9. Cabinet Dimensions: 6.29 in x 4.52 in X 1.14 in (WxHxD)
(160 x 115 x 29 mm)

10.Weight: 1.33 lbs (500g)

11. Video Format: NTSC

3

CONTROLS AND INDICA TORS

FRONT P ANEL

1. Power On LED Indicator

2. Power On/Off Switch

3. Remote Control Sensor

4. Picture Select

5. On Screen Adjustment Up Button

6. On Screen Adjustment Down Button

1

2

3

4

5

6

4

REAR P ANEL

To Optional

To I R Ta n s mi tt er

IR Transmitter

(Optional)

Part Number IRT456

NOTE(B

11

)

12

8

7

10

9

NOTE(A)

7. Power Input Connector: Red = +12 VDC
Black = ground

8. Video Signal Input Connector

9. IR Repeater Connector

10. IR Repeater Transmitter
1 1. Audio Right Channel Input Connector

12. Audio Left Channel Input Connector

5

Note A :

This cable (10) is utilized to connect to Video Cas­sette Players that do not accept the IR Repeater 1/8"
(3.5mm) style plug (9). The IR Repeater Transmitter is
provided with an adhesive that allows it to adhere to
Video Cassette Player remote sensor. Remove the
backing covering the adhesive and place the IR Re­peater Transmitter directly over the Video Cassette
Player remote sensor.

Note B :

Connector (1 1) and (12) are Audio input Jacks reserved
for optional IR Wireless Transmitter use (IRT456).
IR Wireless Transmitter is a device for transmitting
(audio sound without using wires) to IR Headphones.
Please contact Audiovox dealers for this optional ac­cessory .

OPERA TION

1. Connect the monitor power input plug (7) to a DC power
source (Red plug +12 VDC, Black plug (-) to ground).

2. Connect the external video source output signal (from VCP/
DVD, TV Etc.) to the VIDEO IN jack (8).

3. Press power On/Off button (2) to turn the monitor on and off.
The LED power indicator will light red.

4. Press the Picture Select button (4) to adjust the picture dis­play characteristics. The adjustments will be shown on the
On Screen Display in the following sequence: Contrast,
Brightness, Colo r , and TINT.

5. While in the picture select mode (video adjustment), press
the up button (5) to increase the selected adjustment level
or press the down button (6) to decrease the level.

6

GENERAL INST ALLATION INFORMATION

1. Installation will vary from vehicle to vehicle, as headrests in

vehicles are not standard.

2. This unit is intended for installation by professional installers.

3. The kit consists of the screen assembly , a mounting hous-

ing, key to remove screen from housing, wiring harness,
remote control unit and remote control unit batteries.

4. T o release screen from housing, slide the key on either the

right or left side of the screen between the housing and screen
assembly to release the two clips which hold the screen
assembly in the housing.

5. T o install the screen assembly into the housing simply insert

the screen assembly until you hear the clips click into the
locking position.

6. Headrests will have to be cut to install the screen assembly

housing.

Caution - Do not over-cut the headrest beyond the height and

width of the housing.

7. To fasten the housing to the headrest, use either screws or

tie wraps. Find a suitable mounting surface in the headrest
to secure the housing.

Caution - Use the proper length screws, which will vary with

each headrest. If a suitable mounting surface cannot be
found, use tie wraps to secure the housing.

8. Attach the wiring to the screen, through the housing into and

down the headrest and seat before permanently mounting
the housing and screen assembly .

9. Follow the wiring diagram in the owner’s manual for proper

wiring connections.

7

NOTE: A Remote Control Unit is included which will perform

the Functions and adjustments of Operation items 3,
4, and 5 as well as additional features as noted below.

REMOTE CONTROL FUNCTIONS:

LCD/VCP: ........Power button for LCD/VCP

REPLA Y: ..........Press to rewind tape and automatically go to

play mode.

PICTURE SEL: .On Screen Display (OSD) for color , tint, brightness,

contrast. Use ± to adjust

REW: ...............Rewinds tape

FWD: ...............Fast Forward tape

PLA Y : ...............Plays tape

STOP: ..............Stops tape

CAUTION

1. Do not operate the monitor at temperatures below 32°F

(0°C) or above 104°F (40°C).

2. Keep the monitor clean and dry .

3. Always seek qualified personnel to perform repairs. Never

attempt your own repairs.

4. Do not drop the monitor or expose to strong impacts.

5. Do not expose to direct sunlight for extended periods of

time.

© 2000 Audiovox Electronics Corp., Hauppauge, NY 128-5960A

8