Audiovox HR7012S, HR7012 User Manual

Download

Page 1

HR7012

REAR SEAT VIDEO

HEADREST SYSTEM

HR7012S

HR7012

AvAilAble in three configurAtions

• Dual DVD Player DD7012

• Single DVD Player and Monitor DM7012

• Dual Monitor MM7012

Owner’s Manual

Page 2

Page 3

TABLE OF CONTENTS

Contents

Welcome .....................................................................................................................................................................1

HR7012 Rear Seat Video Headrest System Congurations ......................................................................2

Product Features ......................................................................................................................................................3

Cautions ......................................................................................................................................................................4

Quick Start Guide ....................................................................................................................................................5

General Operating Instructions..........................................................................................................................6

Front Panel Controls ...............................................................................................................................................7

Remote Control and Headphone Battery Installation ...............................................................................9

Battery Cautions and Warnings .......................................................................................................................11

Remote Control Operation ...............................................................................................................................12

System Setup Menu ...........................................................................................................................................16

System Setup Sub-Menus .................................................................................................................................18

DVD Playback Settings and Adjustments ................................................................................................... 27

DISC Basics ..............................................................................................................................................................32

Playback of Media ................................................................................................................................................33

DVD Region Codes ............................................................................................................................................... 37

Game Controller Operation ..............................................................................................................................38

Troubleshooting ...................................................................................................................................................39

Specications ........................................................................................................................................................ 40

Compliance Information ....................................................................................................................................41

User Notes .............................................................................................................................................................. 42

Page 4

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

Page 5

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

WELCOME

Thank you for purchasing the HR7012 Rear Seat Video Headrest System. Before operating this system read this manual thoroughly and retain it for future reference.

The HR7012 is a versatile Rear Seat Video Headrest System and is available in three dierent congurations (please refer to page 2 for a detailed description of each of the congurations). Each of the three congurations come with two replacement video monitor headrests referred to as either “M1” or “M2” in this manual. Both the M1 and M2 feature a 7” Monitor equipped with easy to use front panel controls and auxiliary connection options. The system allows the users to watch the same DVD/Video Source on both monitors simultaneously or individual DVD/Video Sources on either monitor. The full function wireless remote control operates either monitor by selecting Monitor Select “M1” or “M2” button.

HR7012M: is a 7” LCD monitor with a built-in DVD player that allows the user to select from several sources (DVD/USB, M2, AV-IN, AUX MEDIA, and GAME* Source). The monitor has a built-in infrared audio transmitter channel.

HR7012S: is a 7” LCD monitor (No DVD)that allows the user to select from several sources (M1, AV-IN, AUX MEDIA, and GAME* Source). The monitor has a built-in infrared audio transmitter channel.

* GAME Optional

The HR7012 Rear Seat Video Headrest System is set-up and adjusted with easy The HR 7012 Rear Seat Video Headrest System is set-up and adjusted with easy to use menus that are accessed using the remote control or the front panel buttons.

The supplied two-channel wireless Infrared (IR) headphones have an A-B switch that allow the users to select the audio from either M1 on “CH. A” or M2 on ”CH. B”

• The M1 monitor will only respond to the remote control when the Monitor Select “M1” button is pressed.

• The M2 monitor will only respond to the remote control when the Monitor Select “M2” button is pressed.

(Optional wired headphones allow the user to listen to audio from the system through the 1/8” jack located on the front of each monitor.)

Licensed under one or more of the following patents: Patent NOS. 7,245,274, 6,899,365, and 6,678,892.

Page 6

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

HR7012 REAR SEAT VIDEO HEADREST SYSTEM CONFIGURATIONS

Available in three congurations as follows: Conguration 1:

Two 7” LCD monitors with a built-in DVD player (HR7012M) (Figure 1.)

Model DD7012

HR7012M

(M2)

HR7012M

(M1)

Figure 1

Conguration 2: Model DM7012

One 7” LCD monitor with a built-in DVD player (HR7012M) and One 7” LCD monitor (screen only) (HR7012S) (Figure 2.)

NOTE: When the M2 Monitor is set to the M1 source and to “AUTO ON”, M2 will turn ON automatically when M1 is in playback mode. (See page 26)

HR7012S

(M2)

HR7012M

(M1)

Figure 2

Conguration 3: Model MM7012

Two 7” LCD monitors (HR7012S) (screens only) connected to automotive head unit (radio) with built-in DVD player or external DVD, Blu-ray player or other A/V source. (Figure 3.)

NOTE: When the Monitors are set to the “A/V” IN source and “AUTO ON” is selected both monitors will turn ON automatically when a video signal is received from a external source. (See page 26)

HR7012S

(M2)

HR7012S

(M1)

Your system may have an additional A/V (Audio/Video) input such as Conguration 3 above

Figure 3

and/or an optional Game Pack (HR7012GP).

HR7012 New Features:

1. When an optional Game Pack is installed, either monitor can be designated as “Player 1”. Selection is based on a “rst come, rst serve” basis. The second monitor will automatically become “Player 2”.

2. AUTO “M1 ON” of the HR7012S (M2) monitor(s) when the HR7012M (M1) is rst turned ON. This is done by selecting “M1” in the Default AUTO ON/OFF sub-menu. (See page 26)

3. AUTO “ON” of the HR7012S (M2) monitor(s) when a video source is detected. This is done by selecting “ON” in the Default AUTO ON/OFF sub-menu. (See page 26)

4. 100 Channel FM Modulator.

Page 7

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

PRODUCT FEATURES

The HR7012 Rear Seat Video Headrest System consists of:

1. Two factory matched Headrests with 7-inch Color TFT-LCD Display Screen (800x480) 16:9 aspect ratio. (See conguration options on previous page)

2. Two Wireless Infrared (IR) Headphones equipped with volume control and A/B switch to select between “M1” and “M2”. Note: The wireless IR headphones must be used within a line of sight from the transmitter as infrared transmission, like visible light, travels only in an unrestricted line of sight.

3. Two Infrared (IR) Transmitters for listening to audio signal through Wireless IR Headphones.

4. One wireless FM transmitter used to listen to audio (M1 only) through the vehicle’s FM radio by tuning to one of 100 frequencies. Try each station frequency until you achieve a clear audio signal.

Note: Whenever the FM transmitter is active, regular radio reception may be poor. Turn the FM transmitter o to allow normal radio reception

5. Two sets of Audio/Video (AUX) Signal Input Jacks (yellow, white and red) used to connect items such as a DVD player, video game device, or other audio/video devices. Two 1/8-inch (3.5mm) Wired Stereo Headset Jacks that can be used with any standard stereo headphones.

6. USB Port (HR7012M only) used to connect a USB memory device (eg. thumb drive) Content on the USB device can be played by selecting “DVD” as the video source. The USB device will automatically start up upon connection, thereby overriding the DVD disc. Disconnect the USB device to play DVD’s and CD’s.

7. Remote Sensor on the Front Panel.

8. One Full Function Remote Control to operate either headrest by selecting “M1” or “M2”.”

9. Control Buttons on the Front Panel

POWER, SOURCE, VOLUME UP/DOWN, STOP, EJECT, MENU/SELECT.

10. OSD (On Screen Display) menus.

Page 8

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

CAUTIONS

Important Notice

An LCD Panel and/or Video Monitor may be installed in a motor vehicle and visible to the driver if the LCD Panel or Video Monitor is used for vehicle information, system control, rear or side observation or navigation. If the LCD Panel or Video Monitor is used for television reception, video or DVD play, the LCD Panel or Video Monitor must be installed so that these features will only function when the vehicle is in “park” or when the vehicle’s parking brake is applied.

An LCD Panel or Video Monitor used for television reception, video or DVD play that operates when the vehicle is in gear or when the parking is not applied must be installed to the rear of the driver’s seat where it will not be visible, directly or indirectly, to the operator of the motor vehicle.

Safety Precaution

For safety reasons, when changing a video disc it is recommended that the vehicle not be in motion, and that you do not allow children to unfasten safety belts to change a disc or make any adjustments to the system. System adjustments can be accomplished using the remote control unit, while safety belts remain fastened. Enjoy your entertainment system but remember that the safety of all passengers remains the number one priority.

CAUTION

Always run the vehicle’s engine while using the HR7012 Rear Seat Video Headrest System. Using this system without running the engine can result in battery drainage. To avoid the risk of battery drainage, please remember to turn o the device when the vehicle is not in use for long periods of time.

Page 9

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

QUICK START GUIDE

Turn ON the Monitors (M1 and M2).

1. Press the Power ON/OFF button. The power indicator will light up red.

2. Insert a DVD, CD, MP3 disc into the disc slot located on top of the M1 monitor (disc label toward user). Push down gently on the disc until the player pulls the disc in (Do Not force disc) or connect a video source through the jacks on the front panel.

3. Tilt the monitor to a comfortable viewing position.

4. The supplied wireless IR headphones have an ”A-B” switch used to select the audio from either the “M1” or “M2” monitor. When sitting in front of the M1 screen, use the CH. A setting. When sitting in front of the M2 screen, use the CH. B setting. Set the headset to the proper channel and press the Power On/O switch. The power indicator will light up red. Turn the volume down to its lowest setting before putting the headphones on.

5. When the DVD menu appears, select the menu item using the UP/DOWN buttons and press Enter or Play button.

6. If audio playback through the vehicle radio is preferred, use the FM transmitter ON/OFF button on the remote control. Set the vehicle radio to the channel selected on the M1 monitor. If interference with a local radio station occurs, set the FM modulator to one of the other 100 radio frequencies using the Channel Select buttons on the remote control or front panel.

Note: To operate the M1 screen, press M1 on the remote control. To operate the M2 screen, press M2.

7. To turn OFF either M1 or M2, press and hold the Power ON/OFF button for 5 seconds or turn the vehicle OFF.

Page 10

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

GENERAL OPERATING INSTRUCTIONS

For best disc operation , it is important that you read this section completely.

DVD Region Coding

The HR7012M and the DVD are coded by region. These region codes must match in order for the DVD to play. If the codes do not match, the DVD will not play. The HR7012M code is set to region 1. Playback of any other region will not work in the HR7012M.

Type of Discs the HR7012M Will Play

• DVD-Video: DVD containing video.

• CD-DA: CD containing musical or sound content only.

• CD-Video: CD contains movie only.

• CD-R/RW: A disc that containing audio les (for example, a CD-R with downloaded MP3 les), MPEG, or JPEG les.

Note: The following discs will NOT play in the HR7012M, Optical disc- CD-1, CD-ROM, and DVD-ROM Mini disc- CDG (audio only, not graphics), Blu-ray.

Loading and Playing Discs

Before loading a disc, make sure that it is compatible with the player.

Press the POWER button to turn the system ON. Load the disc (label facing the user) into the disc slot. The disc will load automatically and begin to play.

Note: Some discs may start at the root menu, where play must be selected to start movie.

Notes on Discs

• Do not touch the disc surface. Handle the disc by the edge.

• It is important that discs are clean prior to use.

• If disc is not clean, use a commercially available cleaning cloth to gently wipe the disc from the center out. (Figure 4)

Note: Do not use solvents such as benzene, thinner, cleaners, or antistatic spray intended for analog discs.

Figure 4

• Keep discs protected in their cases or disc magazines when not in use. Do not subject discs to heat/high temperature. Avoid leaving discs in a parked vehicle or on a dashboard/rear tray.

• Do not use discs that have after-market Paper or plastic labels/stickers attached. The following malfunctions may result from using such discs:

• Inability to eject a disc (due to a label

or sticker peeling o and jamming the eject mechanism).

• Inability to read audio data correctly

(i.e., playback skipping, or no playback) due to heat shrinking of a sticker or label causing a disc to warp.

• Use only standard, round discs. If you insert irregular, non-round, shaped discs they may jam in the DVD player or not play properly.

Page 11

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

FRONT PANEL CONTROLS

Figure 5

1. DVD disc insertion slot (Figures 5 and 6).

2. IR TRANSMITTER and IR SENSOR

IR Transmitter: is used to broadcast audio signal to the wireless IR headphones. IR Sensor: is used to receive signals from the remote control (Figures 5 and 6).

3. Play Button (HR7012M)

This button is used to begin playback of the disc or USB media inserted (Figure 5).

4. EJECT Button

This button is used to eject the disc (Figure 6).

5. SOURCE Button (HR7012M) This button is used to select the DVD/

USB, M1/M2, AV/AUX, MEDIA or GAME (optional) (Figure 5).

6. STOP Button

This button is used to stop the playback

of the disc or USB media in use (Figure 5).

7. POWER Button This button is used to turn the HR7012M/

HR7012S ON and OFF (Figures 5 and 6). (press and hold for 5 seconds to turn OFF)

HR7012M

119

AUDIO

VEDIO

8. AUX Jacks (RCA Type)

The Jacks are intended for temporary

connection of an additional AV source such as a video game device, or other audio/video devices. To play the external device, connect to the AUX Jacks, press the SOURCE button on the front panel of the HR7012M or on the remote control until “AUX” appears on the screen and press PLAY on the connected source (Figures 5 and 6).

9. USB PORT

This port is used to connect a USB device

for playback of content. To view content, select “DVD” as the video source and insert the USB device. The USB device will start automatically and take priority over the DVD. To play DVD’s, disconnect the USB device from the port (Figure 5) .

10. Protective Cover

Used to protect and cover the Headset/

Earbud jack, AV Input jacks and USB port when not in use (Figures 5 and 6).

Page 12

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

FRONT PANEL CONTROLS continued

HR7012S

Figure 6

11. 1/8”Wired Headset/Earbud Output Jacks

These jacks are used to connect two standard wired headphones/earbuds (Figures 5 and 6).

12. MENU/SELECT Button This button is used to display and select

options on the main Setup Menu when a disc or USB media is not inserted. When a disc or USB media is inserted, this button is used to display and select available Disc/Media option (Figures 5 and 6).

13. VOLUME Direction Buttons These buttons are used to raise and lower

the volume. (Figures 6).

14. NEXT / RIGHT Button (HR7012M) This button is used to skip to the next

chapter or track during playback of a disc (Figure 5).

15. PREVIOUS / LEFT Button (HR7012M) This button is used to skip to the previous

chapter or track during playback of a disc (Figure 5).

16. 7-inch TFT LCD Display Screen

(800 x 480) (Figure 5 and 6).

AUDIO

VEDIO

17. PIX Button (HR7012S)

This button is used to control levels of

Brightness, Contrast, Color, Tint and to Reset all picture adjustment levels to original factory settings (Figure 6)

18. SOURCE Button (HR7012S)

This button is used to select the M1/

M2, AV/AUX, MEDIA or GAME (optional) (Figure 6).

19. LEFT/RIGHT Buttons (HR7012S)

These buttons are used to navigate

menu selections on the screen (Figures 6).

Warnings

• Do not use any solvents or abrasive cleaning materials when cleaning the screen. Use only a lightly dampened lint free cloth to wipe the screen if it is dirty.

• Lock the front panel in the fully closed position when not in use. Do not put pressure on the screen, caution children to avoid touching or scratching the screen..

Page 13

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

CR2025 3V

REMOTE CONTROL AND HEADPHONE BATTERY INSTALLATION

Installation of the Remote Control Battery

The remote control comes with a battery already installed with a Pull Tab to prevent battery discharge. Remove the Pull Tab before attempting to use the remote. (Figure 7).

Note: The remote control will only operate this device. It is not a universal remote control and will not control other equipment.

Remote control

Back View

Figure 7

Protective Pull Tab (Clear Plastic )

1. While holding the remote control, insert thumbnail into the battery door side notch (1) and index ngernail into battery door upper notch (2) and slide battery holder open (Figure 8).

2. Install one CR2025 battery (1) (Figure 9).

Note: Make sure that the proper polarity (+ or -) is observed.

3. Slide the battery holder back into the remote control until it locks (Figure 10).

(1)

(2)

(1)

Figure 8 Figure 9

Page 14

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

HEADPHONE BATTERY INSTALLATION

Installation of the Headphone Batteries

The wireless IR headphone unit requires two AAA batteries.

1. Locate the battery compartment cover on the left earphone.

2. While holding the left earphone in one hand, press down on the battery compartment cover and slide it UP and OFF in the direction shown. (Figure 10)

3. Insert two AAA batteries (included), carefully following the markings inside to ensure the batteries are inserted properly ( “+”and “

4. Replace the battery compartment cover. (Figure 10)

-” ends in the correct positions.)

Figure 10

Page 15

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

BATTERY CAUTIONS AND WARNINGS

Cautions and Warnings

• Always keep the monitors, remote control and headphones clean and dry.

• Always seek qualied personnel to perform repairs to the system or individual components of the system. Never attempt

your own repairs.

• Do not drop remote control and headphones or expose to strong impacts.

• Do not expose monitors, remote control and headphones to direct sunlight for extended periods of time.

• Always ensure that the battery is correctly installed in the remote control and headphones with the positive and negative sides in the direction as shown in the battery compartment.

• Use one CR2025(3V) Lithium battery (160MAh) in the remote control.

Do not use dierent types.

• Use two AAA(1.5v) Alkaline batteries in each of the headphones.

Do not use dierent types.

• Do not use old batteries in the remote control or headphones.

• When the battery fails to function, replace it immediately.

• Remove the battery if the remote control and headphones are not used for a month or longer.

• Keep all batteries out of the reach of children. Should the battery be swallowed, immediately consult a doctor.

• When disposing used batteries, please comply with governmental regulations or environmental rules that apply in your area.

Page 16

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

REMOTE CONTROL OPERATION

(1)

(2)

(3)

(4)

(5)

(6)

(7)

(8)

(9)

(10)

(11)

(12)

(13)

(14)

(15)

(17)

(16)

Figure 11

Page 17

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

REMOTE CONTROL OPERATION (continued)

1. (M1) Monitor Select

Press this button to select and control HR7012M (M1) Monitor. (Figure 11)

2. POWER

Press this button to turn the system ON. Press the button again to turn the system OFF. (Figure 11)

3. TV (not applicable) Note: If this button is pressed the remote control will not control DVD functions until the DVD button is pressed again. (Figure 11)

4. SOURCE

Press this button to change the AV source between DVD/USB and a connected AUX source. (Figure 11)

5. PIX

This button is used to make picture adjustments. Each time the button is pressed, the adjustment OSD cycles through bars for BRIGHTNESS, CONTRAST, COLOR, TINT, and RESET. Once the desired adjustment bar is displayed, use the UP/DOWN button to adjust the setting. The bar display will automatically disappear if no adjustments are made within 6 seconds or if any button is pressed. (Figure 11)

6. DVD Source

This button is used to switch connected

sources (DVD and USB). This button is only active when remote control is in the DVD mode and a USB device is connected. (Figure 11)

7. SYSTEM MENU

This button is used to make system setup adjustments. Each time the button is pressed, the adjustment OSD cycles through bars for VOLUME CONTROL, PICTURE CONTROL, FM MODULATOR, OSD LANGUAGE, IRT ON/OFF, and DEFAULT DVD ON/OFF (MI) or DEFAULT AV AUTO ON/OFF (M2). (Figure 11)

8. ENTER

Press this button to make an OSD selection or begins playback of the DVD/USB. (Figure 11)

9. UP/DOWN/LEFT/RIGHT Arrows Press these buttons to navigate the menu selection on the screen. (Figure 11)

10. DISPLAY

Press this button to display current disc

information while the disc is playing. Press UP/DOWN arrow buttons to select the Title or Chapter. For Title/Chapter selection, use the numeric buttons to enter the desired Title/Chapter selection. (Figure 11)

11. PLAY Button

Press this button to initiate play mode

when a disc is loaded in the disc compartment. (Figure 11)

12. SCAN BACKWARD Button

Press this button to search in the

backward direction. Press repeatedly to change the search speed from 2, 4, 8, and 16 times the normal speed. (Figure 11)

13. PAUSE Button

Press this button to pause the playback of

a disc. Pressing pause again or pressing the Play button will resume normal playback. (Figure 11)

14. PREV Button

When a disc has more than one Chapter,

Track, or File, you can move to another Chapter/Track/File. Press this button briey during play to step back to the previous Chapter for DVD-video or Track/File for VCD, SVCD, MP3, CD, etc. (Figure 11)

15. FMM ON/OFF

This button is used to turn the wireless

FM Modulator ON and OFF. (Figure 11)

16. IRT ON/OFF

This button is used to turn the Infrared

Transmitter ON and OFF for Wireless IR Headphones. Pressing M1 then the IRT ON/OFF button will control the IR Transmitter for M1. Pressing M2 then the IRT ON/OFF button will control the IR Transmitter for M2. (Figure 11)

17. Numbers

Decimal number: 0 to 9; and +100: Add

100. Used for selecting tracks on a disc. (Figure 11)

Page 18

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

REMOTE CONTROL OPERATION (continued)

(31)

(30)

(29)

(28)

(27)

(26)

(25)

(24)

(23)

(22)

(21)

(20)

(19)

(18)

Figure 12

Page 19

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

REMOTE CONTROL OPERATION (continued)

18. STOP

Press this button to stop

playback of disc. (Figure 12)

19. NEXT Button

When a disc has more than one

Chapter, Track, or File, you can move to another Chapter/Track/File. Press the button briey during play to select the next Chapter for DVD-video or Track/File for VCD, SVCD, MP3, CD, etc. (Figure 12)

20. AUDIO

Press this button to display and

select the available AUDIO languages in DVD mode. Each time you press the button, the language changes.

Note: The audio languages vary from disc to disc. (Figure 12)

21. SCAN FORWARD Button

Press this button to search in the

forward direction. Press repeatedly to change the search speed from 2, 4, 8, and 16 times the normal speed. (Figure 12)

22. SUBTITLE

Press this button. If the current disc

has dierent subtitle options, this now appears on the screen. Press this button repeatedly until you have reached your desired subtitle option. (Figure 12) NOTE: The Subtitle

selections vary from disc to disc

23. SETUP (Unit must be set DVD source)

Press this button to navigate the Setup

Menu. Please refer to the following pages to congure the system: General Setup Page, Audio Setup Page, Preference Page, and Password Setup Page. (Figure 12)

24. REPEAT

Press this button to switch the repeat

mode by CHAPTER, TITLE, ALL and cancel while playing DVD-video. Other disc types such as VCD, CD, and SVCD that only have two repeat modes that can be selected: TRACK and ALL Note: Both repeat functions of VCD and SVCD need the PBC status set to ON when available. (Figure 12)

25. ZOOM

Press this button to enlarge the picture in the movie by 2x, 3x, and 4x, or shrink the picture in the movie by 1/2, 1/3, and 1/4. (Figure 12)

26. DISC MENU

Press this button to access the

menu of the DVD in play. (Figure 12)

27. VOLUME DOWN (-) or UP (+)

Press this button to increase or

decrease the volume for the wired headphones or select the level of the picture adjustments when the unit is in picture adjustment mode. (Figure 12)

28. MUTE

Press this button to mute the sound

transmitted to the headphones. “MUTE” will be displayed on the screen. Pressing the button again restores sound to the previously set level. (Figure 12)

29. DVD Mode Select

Press this button to control DVD functions. (Figure 12)

30. EJECT

Press this button to eject the disc from the disc slot. (Figure 12) (HR7012M only)

31. (M2) Monitor Select

Press this button to select and control HR7012 (M2) Monitor. (Figure 12)

Page 20

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

SYSTEM MENU

The System Menu allows the user to personalize the HR7012 settings. It is used in the initial setup to adjust the picture quality and customize an adjustable functions. Once the initial settings are customized, they will remain the same until modied or reset to the factory default settings.

NOTE: System Menu changes are best made without a DVD inserted into the unit.

This section describes how to adjust and set settings using the six setup screens (Figure 13):

1. VOLUME CONTROL

2. PICTURE CONTROL

3. FM MODULATOR (M1 Only)

4. OSD LANGUAGE

5. IRT ON/OFF

6. DEFAULT DVD ON/OFF HR7012M DEFAULT AUTO ON/OFF (HR7012S)

HR7012S (M2)HR7012M (M1)

Using the System Menu

Figure 13

Navigating and selecting available settings in the System Menu is accomplished using the Remote Control buttons (Figure 14), or the Front Panel buttons (Figure 15).

Follow the steps outlined in this section to select and customize each of the six adjustable functions (Sub-Menus) listed above, and refer to the sections that apply.

SYSTEM

ENTER

BUTTON

UP,DOWN,

LEFT and

RIGHT

DIRECTION

BUTTONS

Figure 14

HR7012M

MENU SELECT

HR7012S

MENU SELECT

Figure 15

NOTE: Press and Hold the MENU/SELECT button for 5 seconds to access the System Menu.

Page 21

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

SYSTEM SETUP MENU continued)

SYSTEM SUBMENUS

1. Press the SYSTEM MENU button on the remote control (Figure 14) or Press and hold the MENU/SELECT button on the front panel of the system for 3 to 5 seconds (Figure 15) to show the SYSTEM MENU.

2. Use the UP/DOWN direction buttons to select the desired setting in the System Menu screen and press the ENTER button or MENU/SELECT button to select the Sub-Menu screen. NOTE: Selected Items in the System Menu and the Sub-Menus will be highlighted

in green.

3. Use the UP, DOWN, LEFT and RIGHT direction buttons to select an item in the Sub-Menu screen and then press the ENTER button to select.

4. To exit System Menu screen or the Sub-Menu screens at anytime, press the System

MENU button on the remote control or the MENU/SELECT button on the front panel. NOTE: The System Menu and all Sub-Menus will automatic disappear from main screen within 5 or 6 seconds if no selections have been made.

Page 22

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

SYSTEM SETUP SUBMENUS

VOLUME CONTROL Wired Headphones Only)

VOLUME CONTROL from the Front Panel (M1 and M2) (Figure 16):

1. Press and hold the MENU/SELECT button on the front panel of the system (Figure 15) for

2. Use the UP/DOWN direction buttons to select Volume Control and press the

3. Using the LEFT / RIGHT direction buttons, adjust the volume level from “0” to “32” as desired.

4. After volume level selection is made, the Volume Control sub-menu will automatically

(HR7012M)

(HR7012S)

Figure 16

3 to 5 seconds to show the System Menu. (Figure 13)

MENU/SELECT button to enter the sub-menu (Figure 16).

NOTE: Default control volume level set at level 10.

disappear from main screen within 5 or 6 seconds, or press the MENU/SELECT button again to return to the System Menu.

VOLUME

Figure 17

VOLUME CONTROL from the Remote Control (Figure 17):

1. Select M1 or M2 on the Remote Control.

2. Using the using the Volume +/- direction buttons adjust the volume level from “0” to “32” as desired. NOTE: Default control volume level set at level 10.

3. After volume level selection is made, the volume control bar will automatically disappear from main screen within 5 or 6 seconds.

Page 23

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

SYSTEM SETUP SUBMENUS (continued)

PICTURE CONTROL

(HR7012M)

(HR7012S)

Figure 18

PICTURE CONTROL from the Front Panel (M1 and M2) (Figure 18):

1. Press and hold the MENU/SELECT button on the front panel of the system (Figure 15) for 3 to 5 seconds to show the System Menu. (Figure 13)

2. Use the UP/DOWN direction buttons to select Picture Control and press the Menu/Select button to enter the sub-menu.

3. Use the UP or DOWN direction buttons to select one of the four setting in the Sub-Menu (Brightness, Contrast, Color,Tint and Reset). Using the

LEFT/RIGHT direction buttons, adjust the level of the picture setting chosen. NOTE: Levels are set from “0” to “16” for Brightness, Contrast and Color. The levels for Tint is set from “-16” to “+16” . No Tint Control in PAL Mode.

4. After level setting(s) are made, the Picture Control sub-menu will automatically disappear from main screen within 5 or 6 seconds, or press the Menu/Select button again to return

to the System Menu.

PICTURE CONTROL from the Remote Control:

1. Select “M1” or “M2” and press the PIX button to select Picture Control.

Note: Picture control settings for DVD mode are separate from the other A/V sources. After adjusting the DVD picture controls, the user can make separate settings for the other A/V sources.

2. Use the UP/DOWN direction buttons to select one of the four setting

in the Sub-Menu (Brightness, Contrast, Color, Tint and Reset). Using the

3. After level setting(s) are made, the Picture Control sub-menu will automatically disappear

from main screen within 5 or 6 seconds, or press the PIX button again.

4. Select reset to return the picture setting control back to factory defaults.

Page 24

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

SYSTEM SETUP SUBMENUS (continued)

FM MODULATOR

(HR7012M)

Figure 19

FM MODULATOR ON/OFF from the Front Panel (Figure 19):

1. Press and hold the MENU/SELECT button on the front panel of the system for 3 to 5 seconds to show the System Menu. (Figure 13)

2. Use the UP/DOWN direction buttons to select FM Modulator and press the MENU/SELECT button to enter the sub-menu.

3. Use the UP/DOWN direction buttons to select FM Modulator ON/OFF and press MENU/SELECT button to enter selection.

4. Use the UP/DOWN direction buttons to select FM Modulator ON or OFF and press the MENU/SELECT button to enter selection. When ON is selected, the FM Modulator screen will display the channel/frequency the system is set to. When OFF is selected, the FM Modulator screen will display FMM OFF.

5. The FM Modulator sub-menu will automatically disappear from main screen within 5 or 6 seconds, or use the UP/DOWN direction buttons to select BACK to return to the

System Menu. NOTE: See page 22 for FM channel selection.

Page 25

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

SYSTEM

OSD

LANGUAGE

IRT

ON/OFF

MODULA

TOR

DEFAULT

DVD

ON/OFF

VOLUME CONTROL

PICTURE

CONTROL

SYSTEM

VOLUME CONTROL

PICTURE

CONTROL

MODULA

TOR

OSD

LANGUAGE

IRT

ON/OFF

DEFAULT

AUTO

ON/OFF

EXIT

SYSTEM SETUP SUBMENUS (continued)

FM CHANNEL

HR7012M (M1 only)

Figure 20

FM CHANNEL from the Front Panel (M1 Only) (Figure 20):

1. Press and hold the MENU/SELECT button on the front panel of the system (Figure 15) for 3 to 5 seconds to show the System Menu.

2. Use the UP/DOWN direction buttons to select FM Modulator and press the MENU/SELECT button to enter the sub-menu.

3. Use the UP/DOWN direction buttons to select FM Channel and press MENU/SELECT button to enter selection.

4. Use the UP/DOWN/LEFT and RIGHT direction buttons to select the best channel/ frequency from a four page list of one hundred possibilities then press the MENU/ SELECT button to enter selection.

5. When a channel/frequency is selected, the FM Modulator screen will display the channel/ frequency the system is set to.

6. The FM Modulator sub-menu will automatically disappear from main screen within 5 or 6 seconds, or use the UP/DOWN direction buttons to return to the System Menu.

HR7012S (M1 only)

Page 26

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

SYSTEM SETUP SUBMENUS (continued)

FM Channel From the Remote Control (Figure 21):

1. Select “M1” on the Remote Control.

2. Press the System Menu button then use the UP/DOWN direction buttons to select FM Modulator and press the Enter button to enter the FM Modulator sub-menu.

3. Use the UP/DOWN/LEFT and RIGHT direction buttons to select the best channel/ frequency from a four page list of one hundred possibilities then press the MENU/

SELECT button to enter selection. NOTE: When a channel/frequency is selected, the FM Modulator screen will display the channel/frequency the system is set to.

4. The FM Modulator sub-menu will automatically disappear from main screen within 5 or 6 seconds, or use the UP/DOWN direction buttons to select “BACK” to return to the System

Menu.

FM MODULATOR ON/OFF Direct Access Button on the Remote Control (Figure 21):

1. Press the FMM ON/OFF button on the remote control to turn the FM Modulator ON and OFF. When ON is selected, the channel/frequency (FMM xxxxMHz) the system is set to will be displayed on the lower left-side of the main screen. When OFF is selected, FMM OFF will be displayed on the lower left-side of the main screen. The displayed selection will

automatically disappear from main screen within 5 or 6 seconds. (Figure 21)

FMM ON/OFF

BUTTON

Figure 21

Page 27

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

SYSTEM SETUP SUBMENUS (continued)

OSD LANGUAGE

OSD LANGUAGE from the Front Panel (M1 and M2) (Figure 22):

1. Press and hold the MENU/SELECT button on the front panel of the system (Figure 15) for

2. Use the UP/DOWN direction buttons to select OSD Language and press the MENU/

3. Use the UP/DOWN direction buttons to select the desired language then press the

HR7012M (M1)

HR7012S (M2)

Figure 22

to 5 seconds to show the System Menu.

SELECT button to enter the sub-menu.

MENU/SELECT button to save the setting.

OSD LANGUAGE from the Remote Control

4. Select “M1” or “M2” on the Remote Control.

5. Press the SYSTEM MENU button then use the UP/DOWN direction buttons (gure 11) to select OSD Language and press the ENTER button to enter the OSD Language sub-menu.

6. Use the UP/DOWN direction buttons to select the desired language then press the ENTER button to save the setting.

Page 28

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

SYSTEM SETUP SUBMENUS (continued)

IRT ON/OFF

HR7012M (M1)

HR7012S (M2)

Figure 23

IRIRT ON/OFF (M1 and M2) from the Front Panel(Figure 23):

1. Press and hold the MENU/SELECT button on the front panel (Figure 15) of the system for 3 to 5 seconds to show the System Menu.

2. Use the UP/DOWN direction buttons to select IRT ON/OFF and press the MENU/SELECT button to enter the sub-menu.

3. Use the UP/DOWN direction buttons to select IRT ON or OFF and press the Menu/Select button to enter selection. When ON is selected, IRT ON will be displayed on the System Menu screen. When OFF is selected, IRT OFF will be displayed on the System Menu screen.

IRT ON/OFF (M1 and M2) from the Remote Control

4. Select “M1” or “M2” on the Remote Control.

5. Press the System Menu button then use the UP/DOWN direction buttons (Figure 14) to select IRT ON/OFF and press the Enter button to enter the sub-menu.

6. Use the UP/DOWN direction buttons to turn the IRT ON or OFF and press the

ENTER button to enter selection. When ON is selected, IRT will be displayed on the System Menu screen. When OFF is selected, IRT OFF will be displayed on the System Menu screen.

IRT ON/OFF Direct Access Button on the Remote Control

7. Select M1 or M2 on the Remote Control.

8. Press the IRT ON/OFF button to turn the IRT ON or OFF. When ON is selected, IRT ON will be displayed on the System Menu screen. When OFF is selected, IRT OFF will be displayed on the System Menu screen and will disappear from screen within 5sec - 6sec.

Page 29

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

SYSTEM SETUP SUBMENUS (continued)

DEFAULT DVD ON/OFF MODEL DD7012

HR7012M (M1)

HR7012M (M2)

Figure 24

With the “Default DVD ON” feature selected, the unit will default to DVD Mode each time the system is turned ON. For example, if the user is playing a game and the system is turned OFF, the next time the system is turned ON, it will power-up in DVD Mode.

Default DVD ON/OFF from the Front Panel (Figure 24):

1. Press and hold the MENU/SELECT button on the front panel (Figure 15) of the system for 3 to 5 seconds to show the System Menu

2. Use the UP/DOWN direction buttons to select DEFAULT DVD ON/OFF and press the MENU/SELECT button to enter the sub-menu.

3. Use the UP/DOWN direction buttons to select DEFAULT DVD ON or OFF and press the MENU/SELECT button to enter selection.

Default DVD ON/OFF from the Remote Control

1. Select “M1” or “M2” on the Remote Control.

2. Press the System Menu button then use the UP/DOWN direction buttons (Figure 11) to select DEFAULT DVD ON/OFF and press the ENTER button to enter the sub-menu.

3. Use the UP/DOWN direction buttons to select DEFAULT DVD ON OR OFF and press the enter button to make the selection.

Page 30

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

SYSTEM

OSD

LANGUAGE

IRT

ON/OFF

MODULA

TOR

DEFAULT

DVD

ON/OFF

VOLUME CONTROL

PICTURE

CONTROL

SYSTEM

VOLUME CONTROL

PICTURE

CONTROL

MODULA

TOR

OSD

LANGUAGE

IRT

ON/OFF

DEFAULT

AUTO

ON/OFF

EXIT

SYSTEM

OSD

LANGUAGE

IRT

ON/OFF

MODULA

TOR

DEFAULT

DVD

ON/OFF

VOLUME CONTROL

PICTURE

CONTROL

SYSTEM

VOLUME CONTROL

PICTURE

CONTROL

MODULA

TOR

OSD

LANGUAGE

IRT

ON/OFF

DEFAULT

AUTO

ON/OFF

EXIT

SYSTEM SETUP SUBMENUS (continued)

DEFAULT AUTO ON/OFF MODEL MM7012

HR7012S (M1)

HR7012S (M2)

Figure 25

Default AUTO ON/OFF from the Front Panel (Figure 25):

1. Press and hold the MENU/SELECT button on the front panel (Figure 15) of the system for 3 to 5 seconds to show the System Menu.

2. Use the UP/DOWN direction buttons to select DEFAULT AUTO ON/OFF and press the MENU/SELECT button to enter the sub-menu.

3. Use the UP/DOWN direction buttons to select Default Auto AV, M1 or OFF and press the MENU/SELECT button to enter selection.

Note:

• Default Auto AV: HR7012S monitor(s) will automatically turn ON when a connected

video source is detected and turned ON. NOTE: This feature will only work if the

system is installed with an external source connected to the A/V IN of the unit.

• Default Auto M1: HR7012S (M2) monitor(s) will automatically turn ON when the

HR7012M (M1) is rst turned ON.

• Default Auto OFF: HR7012S (M2) monitor(s) will not turn ON automatically when

HR7012M (M1) is turned ON or if a connected video source is detected and turned ON.

Default AV AUTO ON/OFF from the Remote Control

1. Select “M1” or “M2” on the Remote Control.

2. Press the SYSTEM MENU button then use the UP/DOWN direction buttons (Figure 11) to select DEFAULT AV AUTO ON/OFF and press the ENTER button to enter the sub-menu.

3. Use the UP/DOWN direction buttons to select DEFAULT AV AUTO ON/OFF and press the ENTER button to enter the sub-menu.

Page 31

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

DVD PLAYBACK SETTINGS AND ADJUSTMENTS

The DVD Playback Setup Menu contains features and options that allows the user to customize the DVD player. For example, the user can set a language for the on-screen display or prevent DVD playback for children.

USING THE SETUP BUTTON ON THE REMOTE CONTROL

1. Press the SETUP button on the remote. The DVD Setup Menu appears on the screen with four major setup option pages. (Figure 25)

Figure 26

2. Use the UP/DOWN direction buttons to highlight the desired setup option page.

Figure 27

3. Use the RIGHT direction button to enter the desired setup option page.

4. Use the UP/DOWN direction buttons to select the desired options and press Enter to conrm the selection.

5. Repeat steps 3~4 to continue setting all available options in the setup option page.

6. To select a dierent Setup Option Pages, press the LEFT direction button to return to the Setup Menu.

7. Repeat steps 2~5 for each of the Setup Option Pages.

8. Press the SETUP button on the remote control again to exit Setup Menu and save changes.

Page 32

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

SETTINGS AND ADJUSTMENTS (continued)

LANGUAGE SETUP

Language (for On-Screen Display (OSD): The Language setup option page allows the user to select the language for the OSD. The user can either select English, French, Spanish, German or Italian for the OSD language. (Figure 28)

Figure 28

Subtitle: The Subtitle setup option page allows the user to select the language for the OSD. The user can either select English, French, Spanish, German, Italian, Chinese, Japanese, Thai or OFF to be displayed on the screen during playback of a disc.(Figure 26)

Note: The subtitle selection is only available for discs that are recorded in the above listed languages. If the selected, language is not available, the player will play and display on the screen the original language contained in the disc. (Figure 29)

Figure 29

Audio: The Audio setup option page allows the user can select the audio language (English, French, Spanish, German, Italian, Chinese, Japanese or Thai). (Figure 30

Note: The audio selection is only available for discs that are recorded in the above listed languages. If the selected, language is not available, the player will play and display on the screen the original language contained in the disc.

Figure 30

Page 33

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

DVD PLAYBACK SETTINGS AND ADJUSTMENTS (continued)

VIDEO SETUP

TV Display: The T V Display setup option page allows the user to adjust screen aspect ratio to either 4:3 or 16:9. (Figure 31)

4:3) Displays a wide picture with black bands on the upper and lower portions of the

screen.

16:9) Displays a wide picture with black bands on the upper and lower portion of the

screen. The bandwidth will vary, depending on the aspect ratio of the disc.

Figure 31

TV Type: The TV TYPE setup allows the user to match the video output of the player to the broadcast system of a connected TV. This system supports both National Television System Committee (NTSC) and Phase Alternating Line (PAL) television broadcasting standards. (Figure 32)

NTSC) Select this mode if the connected TV is a NTSC system. The video signal of a PAL disc

will be converted to NTSC format

PAL) Select this mode if the connected TV is a PAL system. The video signal of a NTSC disc

will be converted to PAL format

Multi) Select this mode if the connected TV is a multi-system. The video signal format of a

will be in accordance with the video signal of the disc

NOTE: For best performance, this setting should remain at NTSC.

Figure 32

Page 34

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

SETTINGS AND ADJUSTMENTS (continued)

RATING SETUP

Rating: The Rating setup option page allows the user to limit the content of movie playback (G, PG, PG–13, R, NC– 7 and Adult). The lower the value, the more strict the control. The rating level can only be changed using a parental control password. For rst time use the default parental control password is 3308 using UP directional button to enter parental mode, key in the default password (3308) and press ENTER. Press ENTER again to select the parental level, select the level and press ENTER (Figure 33). To change the password to your own password press “Change Password” mode and enter the default password (3308) and press ENTER. Press ENTER and again and key in a new four digit password. After complete press ENTER to end the process. (Figure 34)

Note: The Default Password is 3308. This password is always eective even after you have selected your own password and changed it. To avoid the possibility of others using the default password to set the parental level and change the password, you can record this default password in another area and delete it from this manual. Some discs can be limited depending on the age of users while some discs cannot.

Figure 33

Figure 34

Page 35

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

SETTINGS AND ADJUSTMENTS (continued)

Misc SETUP

Misc Setup: Select “MISC” using the UP/DOWN direction buttons, then press the RIGHT

direction button to enter the Misc menu. Select the subtitle you desire using the UP/DOWN direction buttons, then press “ENTER” to conrm the setting. Press the LEFT direction button to return. (Figure 35)

Figure 35

Load Factory: Load Factory allows you to reset all options to factory settings. * This function

will not aect the Rating control settings. (Figure 36)

Screen Saver

ON -Screen saver will appear

OFF -Screen saver will not appear

Note: The DVD player will enable the Screen Saver mode if the unit is inactive for approximately 2 minutes. (Figure 37)

Figure 36

Figure 37

Page 36

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

DISC BASICS

To get the optimum use out of the DVD player, make sure you read this section completely.

Types of Discs your DVD Player will play

• DVD* disc - DVD discs that contain video.

• Audio disc - Audio CDs that contain musical or sound content only.

• MP3 disc - A disc that contains audio les (for example, a CD-R with downloaded MP3 les).

*This system is capable of playing most recordable DVD formats. However, due to the variety of disc manufacturers and software, playback cannot be guaranteed.

Loading and Playing Discs

Before you load a disc, make sure that it is compatible with the player. Insert the disc with the disc label facing toward the driver.

Note: The following Discs CANNOT be used with this player:

• Mini-Disc

• Laserdisc

• CD-1, CD-ROM, DVD-ROM, Super Audio CD (SACD), DVD Audio, JPEG, BD (Blu-ray Disc).

To load and Play a Disc

1. Press the Power button to turn the unit ON.

2. Select DVD mode and insert the disc (label facing user) into the disc compartment.

3. Push down gently on the disc and the player will pull the disc in.

Audio / Video Inputs and Outputs

Audio Output

The Audio output will provide the Audio signal from the M1 unit. This output can be heard on the Built-In Wireless Modulator.

Page 37

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

PLAYBACK OF MEDIA

PLAYING DVD’s

1. Press the DISPLAY button on the remote control to display the status banner. The banner include Title, Chapter, Angle, Audio, Subtitle, Audio, Subtitle, Title selection & Chapter selection.

2. Title Selection Press the Number (0~9) buttons to initiate a change of title selection, then press ENTER to implement the selection.

3. Chapter selection Press the Number (0~9) buttons to initiate a change of chapter selection, then press ENTER to implement the selection. As you toggle through the options, the repeat option changes at that time. The track, for example, repeats once that track has ended. The selected repeat option loops repeatedly until you turn it o.

PLAYING USB’s

1. The System will detect the insertion of the USB media automatically if no disc is loaded. The system only auto detects the rst media inserted (USB drive); the second media source can be manually selected by pressing the DVD Source button on the remote control.

2. When a disc is inserted, the system will switch to DVD mode immediately regardless if USB media is currently playing.

3. The DVD source (DVD or USB) can only be changed while the DVD is not playing.

4. This system cannot support more than 2 memory partitions on the USB thumb drive.

Note: The system will always default to the DVD when the system detects a disc in the DVD player.

PLAYING MP3 DISC’s

CD-R discs that have been encoded in MP3 format can be played on your DVD player. The DVD player plays the songs in the order they were burned on to the disc. When playback is started the elapsed time of the track that is playing will be displayed.

Selecting Folders and Songs

When a device containing MP3 les is loaded in the player, the navigation menu appears automatically.

1. Use the UP/DOWN direction buttons to move the highlight to the desired folder (if present) on the left side of the menu and press ENTER. The songs in the folder will be displayed on screen.

2. Use the UP/DOWN direction buttons to highlight the desired track containing the song and Press ENTER to begin track playback.

Page 38

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

PLAYBACK OF MEDIA (continued)

Skipping Songs

Use the NEXT button on the remote control to move to the next song. Use the Previous button to move to the previous song.

Selecting a Play Mode

Filter (For MP3 & JPEG only)

Filter Mode enables or disables the display of les contained on the media based on their le extension. (Figure 38)

The lter function applies to the following formats:

Audio - Audio data format (MP3, WMA)

Photo - Photo data format (JPEG)

Video - Video data format (MPEG , )

Figure 38

Flat Mode: play the entire disc

This mode is always on (default). During the Flat Mode, all the data folder with MP3, JPEG & Movies will be played in sequence. If the Flat Mode function is o, it will only play the selected folder; other folders are disabled. (Figure 39)

Figure 39

Page 39

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

Figure 40

PLAYBACK OF MEDIA continued

Repeat: Play Repetitively

Repeat function has 4 options : O, Single, Folder and All. Move cursor to Repeat Function and press ENTER, each time ENTER is pressed the unit will cycle through the available options (O/Single/Folder and All are displayed in that order). Repeat default is OFF; (Figure 40)

O Turn o repeat function

Single Repeat the song being played until STOP is pressed.

Folder Play all songs in a folder repetitively

All Play all songs on the disc repetitively

Mode: Play Mode

The Mode function has 4 options: Normal, Shue, Random and Music Intro. Move cursor to the Mode function area and press ENTER repeatedly till the desired mode is displayed. Normal/Shue/Random/Music Intro are displayed in that order. The Mode function default is Normal. (Figure 41)

Normal: Play all songs in folder once.

Shue: Play songs in a folder in a shue order. Each song in the folder is played only once.

Random: Play songs in a folder in a random order. Each song in a folder will only be played

once.

Music Intro: Play each song in order in the folder for 10 seconds The purpose of the “Music Intro” function is to provide the user with a sample of each song for 10 seconds, thereby

making it easy to select and listen to a favorite song.

Figure 41

Page 40

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

PLAYBACK OF MEDIA continued

Add to program

Method: To add the selected songs into Browser view, make sure disc playback is OFF. Move

cursor to “Edit Mode” function and press ENTER. After “Edit Mode” is selected, move cursor to songs list and select the songs which will be compiled and press ENTER. A check mark appears to the left of the selected song; to add the selected songs to the program, move cursor to the “Add to Program” function and press ENTER. The selected songs is added into a new program list and the check mark will disappear on play list, move cursor to “Program View” function and press ENTER to browse the songs in the program. Press PLAY button to play the selected songs. (Figure 42)

Note: Edit Mode, Program View or Add to Program functions are relationship related when selecting the preferred song add to the songs list.

Figure 42

Clear program

Method: To clear the selected song les, press the STOP button twice during playback mode. Move the cursor to the “Edit Mode” function and press ENTER. After “Edit Mode” is selected, move cursor to selected songs list and select the songs you want to delete. Press ENTER and a check mark will appear to the left of the selected song. Move the cursor to clear program and press ENTER, the selected songs will be deleted from the play list. (Figure 43)

Figure 43

Page 41

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

DVD REGION CODES

The DVD player is preset to a region code at the factory depending on where the DVD player is sold. DVDs from a dierent region cannot be played in this unit and the unit will display “WRONG REGION”. (Figure 44)

Figure 44

Region 1- USA, Canada

Region 2- Japan, Europe, South Africa, Middle East, Greenland

Region 3- S. Korea, Taiwan, Hong Kong, Parts of South East Asia

Region 4- Australia, New Zealand, Latin America (including Mexico)

Region 5- Eastern Europe, Russia, India, Africa

Region 6- China

Page 42

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

GAME CONTROLLER OPERATION

Battery Installation (Figure 45)

Before attempting to operate your game controller, install the batteries as described below:

1. Turn the game controller face down. Using a nger, slide battery cover o in the direction of the arrow.

2. Install three “AAA” batteries. Make sure that the proper polarity (+ or -) is observed.

3. Align the cover tabs with the game controller and slide the cover until it locks.

Functional Description (Figure 46)

SELECT

START

DIRECTION

KEYS

P1 GAME CONTROLLER

START

1. Use the START button to enter the games list (1-54). Then use the direction buttons to move the arrow to the desired game. Press START to select the game. Use select button to exit the game list.

2. A Key : “A Function Key” activates the jump and optional weapons.

3. B Key : “ B Function Key” activates Bullet re and attack.

4. TA Key : TURBO “A” Function Key.

5. TB Key : TURBO “B” Function Key.

6. S Key : No function.

7. Press START to begin the game. Press START again at any time to pause the game.

Two Player Games

The game source can be selected from either monitor. The optional game package (HR7012GP) allows either or both users to play video games.

• Player 1 is on a rst come, rst served basis.

• If the M2 user selects the game rst they are automatically Player 1 and if the M1 user

wants to play against the M2 user they become Player 2.

• If the M1 user selects the game rst they are automatically Player 1 and if the M2 user

wants to play against the M1 user they become Player 2.

Bottom Side of Game Controller

Battery Case

Figure 45

LCD-POWER

INDICATOR

P2 GAME CONTROLLER

Figure 46

1.5V AAA

SELECT

START

Page 43

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

TROUBLESHOOTING

Symptom Remedy

Device does not power “ON” • Is the ignition turned “ON”?

• Is the screen rotated to the operating position?

• Are batteries installed in remote control?

IR sensor inoperative • Verify that the batteries in the remote control are good.

• Verify that the remote sensor eye is not obstructed.

• Verify that M1 or M2 has been selected correctly.

Disc won’t play • Insert a disc with label side facing toward user.

• Check if the disc is defective by trying another disc.

• Check the type of disc you put into DVD compartment slot. This DVD player only plays DVDs, audio CDs, and MP3s. It will not play a Blu-ray disc.

• Both the device and the disc are coded by region. If the regional codes don’t match, the disc can’t be played.

Disc plays, but then stops immediately

No picture • Check that you are in DVD mode if playing a DVD

Distorted picture • Check the disc for ngerprints and clean with a soft cloth,

Cannot advance through a movie

No sound or distorted sound • If you are using the IR headphones, make sure you turn ON

Device feels warm • When the device is in use for a long period of time, the

Player does not respond to all commands during playback

• The disc is dirty and needs cleaning.

• Condensation has formed. Allow the player to dry out.

• The disc is scratched. Replace the disc.

wiping from center to edge.

• Sometimes a small amount of picture distortion may appear. This is not a malfunction.

• You cannot advance through the opening credits and warning information that appears at the beginning of movies because the disc is programmed to prohibit that action.

the IR transmitter on the DVD system.

• Verify that the batteries in the IR Headphones are good.

• Is volume turned “UP” on IR Headphones?

• Is anything blocking signal between the monitor and the Headphones?

• Make sure your DVD player is connected properly. Make sure all cables are securely inserted into the appropriate jacks.

• The disc is loaded backwards. Turn the disc around so that the disc is facing towards the driver.

surface will be heated. This is normal.

• Operations are not permitted by the disc.

• Refer to the instructions in the disc inlay.

Page 44

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

SPECIFICATIONS

Monitor Specications

Type TFT Active Matrix LCD

Resolution 2400 (W) x 480 (H)

Pixels 1,152,000

Back Light LED

Power Source +12 VDC

Power Consumption 28W

Operating Temperature 32°F ~ 125°F (0°C ~ +55°C)

Storage Temperature -22°F ~ 150°F (-20°C ~ +70°C)

Video Display System NTSC/PAL

Back Light Life 20,000 hours

Headphone Audio Output 0.03W @ 32 ohm

Page 45

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

COMPLIANCE INFORMATION

FCC Notice

This device has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This device generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this device does cause unacceptable interference to radio or television reception, which can be determined by turning the device OFF and ON, the user is encouraged to try to correct the interference by one or more of the following measures:

• Increase the separation between the device and receiver.

• Consult your dealer or an experienced radio/TV technician for help.

FCC Warning:

To assure continued FCC compliance, the user must use the provided grounded power supply cord and the shielded video interface cable with bonded ferrite cores. Also, any unauthorized change or modications to this device would void the user’s authority to operate this device.

Notice

Disposal of Old Electrical & Electronic Equipment (Applicable in the European Union and other European countries with separate collection systems)

This symbol on the product or on its packaging indicates that device shall not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this device is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this device. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this device, please contact your local city oce, your household waste disposal service or the shop where you purchased the device. Applicable accessory: remote control.

Macrovision Notice

This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.

Page 46

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

USER NOTES

Page 47

HR7012 REAR SEAT VIDEO HEADREST SYSTEM Owner’s Manual

Page 48

If you have any questions regarding this product or require technical assistance, please call 1-800-225-6074

128-9046