Audiovox Home Theater Sytem User Manual [en, es, fr]

iTE^ta^l^lart^icnlrE^tnCt^icrBttr

S^te^reoSy^stenB

CALL TOLL-FREE FOR ANSWERS TO INSTALLATION PROBLEMS

Continental U.S./Canada : 1 - 800 - 645 - 4994

Monday - Friday : 9:00 AM - 7:00 PM Eastern Time

Saturday : 9:00 AM - 5:00 PM Eastern Time

IMPORTANT - RETAIN THIS DOCUMENT FOR FUTURE REFERENCE.

COnE^Isfesc^ ’ Insta^llat^lon

des Systèmes Stéréo

APPELEZ LE NUMERO VERT POUR TOUTE QUESTION CONCERNANT L’INSTALLATION

Territoire Continental Des E.U./Canada : 1 - 800 - 645 - 4994

Lundi au Vendredi : 9 H -19 H Heure de la Côte Est

Samedi : 9 H -17 H Heure de la Côte Est

IMPORTANT - CONSERVER CE DOCUMENT POUR TOUTE REFERENCE ULTERIEURE.

I^^mcc^1o^p^ralaI^t^léc^1cn

de ^Istenes Est^reofémc^

LLAME SIN CARGO PARA FORMULAR PREGUNTAS SOBRE PROBLEMAS DE INSTALACION

Territorio Continental De EE.UU./Canada : 1 - 800 - 645 - 4994

Lunes a Viernes : 9:00 AM - 7:00 PM Zona Horaria del Este

Sabados : 9:00 AM - 5:00 PM Zona Horaria del Este

IMPORTANTE - GUARDE ESTAS INSTRUCCIONES PARA CONSULTARLAS EN EL FUTURO.

INSTALLATION INSTRUCTIONS

This unit is designed for installation in cars, trucks, and vans with an existing radio opening. In many cases, a special installation kit will be required to mount the radio to the dashboard. These kits are available at electronics supply stores and car stereo specialist shops. Always check the kit application before purchasing to make sure the kit works with your vehicle. If you need a kit but cannot find it available, call our toll-free “HELP” line.

UNIVERSAL INSTALLATION

1. Inspect the Existing Radio Opening A. Use the trimplate supplied with the radio to cover the existing dashboard opening. If it completely

covers the opening, you can install the radio without an installation kit. If it does not cover the opening, you will need an installation kit.

B. Check that there will be sufficient space behind the dashboard for the radio chassis.

2. Wire the Radio to the Vehicle’s Wiring A. In most cases, it is easier to wire the radio before mounting it. Place the radio near the dashboard

so the wires can be led through the opening.

B. Carefully follow the wiring diagram in this manual and make certain all connections are secure and

insulated with wire nuts or electrical tape to insure proper operation of the unit.

C. After completing the wiring, turn the unit on to confirm operation (ignition switch must be “on”). If

unit does not operate, re-check all wiring until the problem is corrected. Once proper operation is achieved, turn off unit and ignition switch, and proceed with final mounting of the radio.

3. Mounting the Radio A. Thread a shaft nut half-way down each radio shaft. B. Place a metal back-up plate on each radio shaft against the shaft nut. C. Position the radio behind the dashboard opening so that the back-up plates are snug against the

back of the opening. Adjust the shaft nuts behind the back-up plates so that the desired amount of radio nosepiece extends through the opening. The best appearance is usually achieved when

there is just enough of the radio extending to be flush with the front of the trimplate. D. Place the trimplate over the front of the radio and secure it with a shaft nut on each radio shaft. E. Attach one end of the perforated support strap (supplied) to the screw stud on the radio using the

hex nut provided. Bend the strap to position it as necessary.

CAUTION: The rear of the radio must be supported with the strap to prevent damage to the

dashboard from the weight of the radio or improper operation due to vibration. F. Install knobs on the radio.

INSTALLATION USING KITS

1. If your vehicle requires the use of an installation kit to mount this radio, follow the instructions included with the installation kit to attach the radio to the mounting plate supplied with the kit.

2. Wire and test the radio as described in section 2 above.

3. Install the radio/mounting plate assembly to the sub-dashboard according to the instructions of the installation kit.

4. Attach the support strap to the radio and dashboard as described in section 3-E above.

5. Replace the dashboard trimpanel and install knobs on the radio shafts.

Form No.128-5257

+ 2 hidden pages