Audiovox HD5212 Installation And Operation Manual

52

Watt s Peak
Watt s en Cr ête
Vatio s el Máx imo

13W x 4

HD5212

Installation and Operation Manual

SAT

READY

PRESS

RPT SHFSCN

1

2

3

4

5

6

SEL

CAT/DIR

AUX IN

MONO

DISP

EQ

BAND

SRC

TUNE/CH

MUTE

A~Z
0~9

PS

ENTER

IPOD

FILE/FOLDER

SAT

READY

HD5212

i

HD5212

TABLE OF CONTENTS

Introduction ..............................................................................................1

Preparation ..............................................................................................2

Wiring .............................................. ....................................................... ..3

Installation ................................................. ...............................................4

Front Panel Release ................................................................................7

Operation .................................................................................................8

Tuner Operation .....................................................................................11

Satellite Radio Operation ....................... ... ... ... ....... ... ... ... .... ... ... ... .... ... ...13

CD Player Operation ................................................. ... ... .... ...................15

MP3/WMA Operation .............................................................................17

iPod Operation .......................................................................................21

Remote Control ......................................................................................23

Care and Maintenance ...........................................................................24

Troubleshooting .....................................................................................25

Specifications ............................................ .............................................26

ii

HD5212

1

HD5212

Introduction

Congratulations on your purchase of the Jensen HD5212 Mobile Receiver.
It’s a good idea to read all of the instructions before beginning the
installation. We recommend having your Jensen HD5212 installed by a
reputable installation shop.

Features

• Built in HD Radio™ Tuner*

• Made for iPod

• XM and Sirius Satellite Radio Ready

• Supports MP3/ WMA files via CD- R/RW, SD card, or USB

• 24 Station Presets (18 FM/ 6 AM)

• Electronic Detachable Faceplate

• Rear Pre-amp Line Output

• 2MB ESP

• Last Position Memory

• Random, Repeat, Intro

• LCD Dimmer

• Preset EQ- Rock, Pop, Classic

• Loudness

• Electronic Bass, Treble, Balance, Fader

• jLink iPod Cable and 3.5mm Media Adapter Cables Included

• Infrared remote control

*HD Radio™ T echnology Man ufactured Under License From iBiquity Digi tal
Corp. U.S. and Foreign Patents. HD Radio™ and the HD Radio logo are
proprietary trademarks of iBiquity Digital Corp.

2

HD5212

Preparation

Tools and Supplies

The following tools and supplies are needed to install the radio.

• Torx type, flathead and Philips screwdrivers

• Wire cutters and strippers

• Tools to remove existing radio (screwdriver, socket wrench set or other
tools)

• Electrical tape

•Crimping tool

• Volt meter/test light

• Crimp connections

• 18 gauge wire for power connections

• 16-18 gauge speaker wire

SPEAKER REQUIREMENTS: Only connect speakers rated in the load
impedance of 4 ohms. Speakers with a load impedance less than 4
ohms could damage the unit.

Disconnecting the Battery

To prevent a short circuit, be sure to turn off the ignition and remove the
negative (-) battery cable prior to installation.

Removing the Transport Screws

Before installing the radio, you must remove the transport screws from the
top of the radio. The transport screws are clearly marked.

NOTE: If the HD5212 is to be installed in a car equipped with an on­board drive or navigation computer, do not disconnect the battery
cable. If the cable is disconnected, the computer memory may be lost.
Under these conditions, use extra caution during installation to avoid
causing a short circuit.

WARNING! Only connect the unit to a 12-volt power supply with
proper grounding.

WARNING! Never install this unit where operation and viewing could
interfere with safe driving conditions.

WARNING! Never disassemble or adjust the unit.

WARNING! Avoid installing the unit where it will be subject to
excessive temperature, such as from direct sunlight or hot air from the
heater, or where it will be subject to dust, dirt or excessive vibration.

WARNING! T o prevent injury fr om shock or fire, never exp ose this unit
to moisture or water.

WARNING! Never use irregular discs.

WARNING! Using an improper fuse may c ause damage to the unit and
result in a fire.

Remove before installation.

3

HD5212

Gray/Black (-)

Gray (+)

White/Black (-)

White (+)

Violet (+)

+

Green (+)

Green/Black (-)

Violet/Black (-)

15A

iPod NanoiPod MiniiPod

iPod Gen5

Power Antenna (BLUE)

Connect to power antenna

or amplifier.If not used,

tape bare end of wire.

Accessory/Ignition (RED)

Connect to existing radio
wire or radio fuse.

Ground (BLACK)

Connect to ground
terminal or clean,
unpainted part of chassis.

Memory/Battery (YELLOW)

Connect to battery or 12 volt
power source that is always live.
The radio will not work if this
wire is not connected.

Amplifier Wiring (GRAY)

Connect line out for optional
external amplifiers. The RED
connector is for the right and

the WHITE connector is

for the left.

Antenna Connector

LF/AVG

RF/AVD

LR/ARG

RR/ARD

TERK XMDJEN100 cables sold separately.
TERK XMD1000 Direct Tuner and antenna sold separately.

tuner sold separately.SiriusConnect SC-C1

SIRIUS XM XM L XM R

JLink iPod
Cable (Included)

Satellite

Radio
Tuner

Wiring

4

HD5212

Installation

This unit is designed for installation in cars, trucks and vans with an existing
radio opening. In many cases, a special installation kit will be required to
mount the radio into the dashboard. These kits are available at electronics
supply stores and car stereo specialty shops. Always check the kit
application before purchasing to make sure the kit works with your vehicle.
If you have trouble locating a kit or need installation assistance, contact
Technical Support at 1-800-323-4815 from 8:30am to 7:00pm EST M onday
through Friday and from 9:00am to 5:00pm EST on Saturday.

Universal Installation Using Mounting Sleeve

1. Remove the detachable front panel, if it is attached to the chassis, by
pushing the “Release” button.

2. Slide the mounting sleeve off of the chassis if it has not already been
removed. If it is locked into position, use the removal keys (supplied) to
disengage it. The removal keys are depicted on page 6.

3. Check the dashboard opening size by sliding the mounting sleeve into
it. If the opening is not large enough, carefully cut or file as necessary
until the sleeve easily slides into the opening. Do not force the sleeve
into the opening or cause it to bend or bow. Check that there will be
sufficient space behind the dashboard for the radio chassis.

4. Locate the series of bend tabs along the top, bottom and sides of the
mounting sleeve. With the sleeve fully inserted into the dashboard
opening, bend as many of the tabs outward as necessary to firmly
secure the sleeve to the dashboard.

5. Place the radio in front of the dashboard opening so the wiring can be
brought through the mounting sleeve.

6. Follow the wiring diagram carefully and make certain all connections
are secure and insulated with crimp connectors or electrical tape to
ensure proper operation.

NOTE: The amplifier in this radio is only designed for use with four
speakers. Never combine (bridge) outputs for use with two speakers.
Never ground negative speaker leads to chassis ground. Failure to
wire exactly as shown may cause electrical damage to the radio.

7. After completing the wiring connections, attach the front panel and turn
the unit on to confirm operation (vehicle ignition switch must be on). If
the unit does not operate, recheck all wiring until the problem is
corrected. Once proper operation is achieved, turn the ignition switch
off and proceed with final mounting of the chassis.

8. Carefully slide the radio into the mounting sleeve making sure it is right­side-up until it is fully seated and the spring clips lock it into place.

2

1

3

5

4

Mounting Bolt

Spring Washer

Plain Washer

TappingScrew

Hex Nut

PRESS

RPT SHFSCN

1

2

3 4

5

6

SEL

CAT/DIR

AUX

I
N

MONO DISP

EQ

BAND

SRC

TUNE/CH

MUTE

A~Z
0~9

PS

ENTER

IPOD

FILE/FOLDER

HD5212

SAT

R
E
A

D
Y

5

HD5212

9. Attach one end of the perforated support strap (supplied) to the screw
stud on the rear of the chassis using the hex nut provided. Fasten the
other end of the perforated strap to a secure part of the dashboard
either above or below the radio using the tapping screw and washer
provided. Bend the strap, as necessary, to position it. CAUTION: The
rear of the radio must be supported with the strap to p revent damage to
the dashboard from the weight of the radio or improper oper ation due to
vibration. The strap also ensures proper electrical grounding of the unit.

10. Re-attach the front panel to the chassis and test radio operation by
referring to the operating instructions for the unit.

NOTE: For proper operation of the CD player, the chassis must be
mounted within 20° of horizontal. Make sure the unit is mounted within
this limitation.

ISO Installation

This unit has threaded holes in the chassis side panels which may be used
with the original factory mounting brackets of some vehicles to mount the
radio to the dashboard. Please consult with your local car stereo shop for
assistance on this type of installation.

1. Remove the existing factory radio from the dashboard or ce nter console
mounting. Save all hardware and brackets as they will be used to mount
the new radio.

2. Carefully unsnap the plastic frame from the front of the new radio
chassis. Remove and discard the frame.

3. Remove the factory mounting brackets and hardware from the existing
radio and attach them to the new radio using the same screws. Do not
exceed M5 x 9 MM maximum screw size. Longer screws may damage
components inside the chassis.

4. Wire the new radio to the vehicle as outlined in the Universal Installation
instructions.

5. Slide radio chassis into dash opening and secure with factory radio
screws.

6. Reinstall dash panel

Kit Installation

If your vehicle requires the use of an installation kit to mount this radio,
follow the instructions included with the installation kit to attach the radio to
the mounting plate supplied with the kit.

1. Wire and test the radio as outlined in the Universal Installation instruc­tions.

2. Install the radio/mounting plate assembly to the sub-dashboard
according to the instructions in the installation kit.

3. Attach the support strap to the radio and dashboard as described in the
Universal Installation instructions.

4. Replace the dashboard trim panel.

Fuses

When replacing a fuse, make sure the new fuse is the correct type and
amperage. Using an incorrect fuse could damage the radio. The HD5212
uses one 15 amp fuse located below the wiring connector (15 amp fast blow
ATO).

Reconnecting the Battery

When wiring is complete, reconnect the battery negative terminal.

5

6

3

2

4

PRESS

RPT SHFSCN

1

2

3 4

5

6

SEL

CAT/DIR

AUX

IN

MONO

DISP

EQ

BAND

SRC

TUNE/CH

MUTE

A~Z
0~9

PS

ENTER

IPOD

FILE/FOLDER

HD5212

SAT

SAT

READY

READY

ISO INSTALLATION

6

HD5212

Removing the Radio

To remove the radio after installation,
remove the trim ring by pulling outward
on one side and then the other. Insert
the removal keys straight back, with the
notches facing up, until they lock. With
the removal keys engaged, pull the
radio straight out. If removal keys are
inserted at an angle, they will not lock
properly to release the unit.

Connecting the Satellite Radio Receiver
(optional)

Before you can listen to satellite radio, you must install the satellite receiver
and antenna (purchased separately). The satellite radio receiver is the
central data receiving equipment required to process the satellite signals
from the external antenna. It is typically installed in the dash, under the seat,
or in the trunk or rear of the vehicle. Do not mount receiver near a heater
vent or where it can be exposed to extreme temperatures. In additi on, when
running the wire for the external antenna do not kink or pinch th e an te nn a
cable. A sharp 90 degree bend or slight "nick" to the outer cable sheath will
cause signal degradation. The wiring diagram will help you identify the
proper connections.

Technical Assistance

If you require assistance, contact Technical Support at 1-800-323-4815
from 8:30am to 7:00pm EST Monday through Friday and from 9:00am to
5:00pm EST on Saturday.

REMOVAL KEYS