Page 1
Owner’s Manual
Model FR-200
Two Way Family Radio
TX
BATT
CALL
Family Radio Service
Customer Service
Rev NC Released on 4-21-99.
Rev A 4/22/99 Changed # to 1-800-645-4994
Rev B 4/27/99 1st production-Changed bat save time to 5 sec, ch A
to 462.5625
Rev C 5/11/99 2nd production-Added adj limit conformation, batt
indicator on pwr save call and up/down, added Family radio service
to dwgs, changed turn on from instant to 2 sec button press.
Rev D 5/27/99 3rd production-Removed references to bat low light
except on low batt condition. Added monitor lock feature.
1-800-645-4994
128-5551D
1of12
Page 2
CONGRATULATIONS ON YOUR SELECTION
OF THE FR-200 (FAMILY RADIO)
It is one of the most sophisticated and reliable two way
Family radios available.
BEFORE OPERATING YOUR FR-200 (FAMILY RADIO)
READ THIS MANUAL CAREFULLY
FCC WARNING
Replacement or substitution of transistors, diodes or other
parts of a unique nature, with parts other than those
recommended by the manufacturer, may cause a violation
of the technical regulations of Part 15 of FCC Rules.
128-5551D
2of12
Page 3
FEATURES
Your FR-200 Family Radio is a portable, easy to use, two-way
radio that you can carry almost anywhere. It is skillfully constructed
to give you reliable communications for many different applications.
The FR-200 is ideal for use around the house, in your boat, on
hunting and camping trips, on the ski slopes or at the mall.
PERFORMANCE
Your transceiver will achieve its maximum operating range when
communicating with other transceiver(s) in a flat open area with
no trees or buildings obstructing its signal. Range may be up to
two miles under such conditions. Obstacles such as buildings,
trees or mountains will tend to reduce the transceiver’s effective
range.
-1-
128-5551D
3of12
Page 4
FUNCTION AND LOCATION OF THE CONTROLS
14
15
1
13
2
3
P
M
12
11
TX
BATT
CALL
C
Family Radio Service
8
9
4
10
7
6
16
5
-2-
128-5551D
4of12
Page 5
1. Power Button: Press and hold this button for 2 seconds to turn the
transceiver on or off.
2. Push-to-Talk Button: Press to transmit. Release to
receive.
3. Monitor Button: Press and hold to bypass the squelch and
listen to channel activity.
4. Belt Clip
5. Battery Compartment
6. Speaker
7. Microphone
8. Call Button: Press and hold this button to send a ringing sound to
other radios tuned to the same channel.
9. Up Button: Press this button to increase the volume.
10. Down Button: Press this button to decrease the volume.
11. Low Battery Indicator: Illuminates when the battery level is
low.
12. Transmit Indicator: Illuminates while transmitting.
13. Antenna: Rotate counterclockwise when transceiver is in use
14. Microphone / Charger Jack: For use with an external micro
phone / PTT button and optional battery charger.
15. Speaker Jack: For use with an Audiovox approved headset
accessory only.
16. Channel Select Switch: Selects channel of operation
-3-
128-5551D
5of12
Page 6
BATTERY INSTALLATION
Your FR-200 requires four “AAA” alkaline cells or
four rechargeable “AAA” cells. Alkaline batteries
will provide the best performance from your
transceiver. Remove the battery cover by rotating
the belt clip away from the battery compartment.
Slide the battery cover downward while applying
pressure at its grooved section. Observe the
polarity symbols inside the battery tray when
installing the batteries.
CAUTION:
Incorrect battery installation can damage the unit.
The microphone / charger jack is intended for use with Audiovox
approved charging accessories only. Refer to the documentation
included with the battery charger .
Never attempt to charge alkaline batteries with the optional battery
charger.
-4-
128-5551D
6of12
Page 7
USING YOUR FR-200
Turning the Transceiver on
Pressing the power button for 2 seconds will activate the unit. The
speaker will play a conformation beep tone to confirm the FR-200’s
activation. Toturn the unit off, simply press and hold the power button
for 2 seconds. The unit will play a tone to confirm its shutdown.
Button Conformation Tones
The FR-200 will confirm each press of the up or down buttons with
a conformation tone. The tone will correspond to the current volume setting, the lower the tone, the lower the setting. A unique tone
will indicate that the limit of adjustment has been reached.
Low Battery Alert
When the batteries are in need of replacement or charging, the low
battery indicator LED will flash once every ½ second and the
transceiver will sound a double beep to alert the user.
To Select a Channel
Move the channel select switch upward for
Channel A (FRS Channel 1) or downward for
Channel B (FRS Channel 8)
Call Signals
Channel
Select
Switch
When the call button is pressed, the FR-200
will transmit a three-second ringing sound to all other
transceiver’s tuned to the same channel. This feature
can be used to signal other parties that voice
communication is desired.
-5-
128-5551D
7of12
Page 8
To Transmit
1. Set the desired channel.
2. Press and hold the P (Push-to-Talk) button while speaking slowly
and clearly in a normal voice, approximately 2 to 3 inches
from the microphone.
3. The transmit indicator will illuminate while transmitting.
4. Release the P (Push-to-T alk) button when you finish speaking to
receive incoming signals.
To Receive.
1. Set the desired channel.
2. Adjust the volume control to the desired listening volume by
using the up and down buttons while listening to the button
conformation tones
3. The transceiver will play strong signals through its internal
speaker or through a headset if so equipped.
Monitor Function
The monitor button can be used to play all signals present on a
channel. This is useful when communicating with other parties at
extreme range.
The monitor function can be locked on by pressing its button for
three seconds. A confirmation tone indicates that the monitor
lock has been activated. Pressing the monitor button a second
time will unlock the monitor function.
-6-
128-5551D
8of12
Page 9
WARNING
Remove the batteries from the transceiver if it is not expected to
be used for long periods. This will eliminate the possibility of
battery acid leaking from the batteries and corroding the transceiver.
Avoid exposing the unit to water or extremes of temperature.
Do not use this device in or near a mining facility, which uses
remotely triggered explosives or in areas labeled “Blasting Area”.
Premature or accidental detonation may result.
Do not attempt to modify or in any way increase the output of this
transceiver. Its output is designed to meet the legal limits set by
the FCC.
Do not use this device or change its batteries in potentially explosive
atmospheres as sparks in such areas could result in an explosion.
Turn your transceiver off wherever posted notices restrict the use
of radios or cellular telephones. Facilities such as hospitals may
use equipment that is sensitive to RF energy.
Turn your transceiver off on board aircraft when requested to do so.
Do not place your transceiver in front of a vehicle’s air-bag. If the
air-bag deploys, it could propel the transceiver like a projectile.
This transceiver complies with F.C.C. regulations for use in the
United States. Use in other countries may be prohibited or restricted
by local regulation. Please check with the local regulating agency
before using this device outside of the United States.
-7-
128-5551D
9of12
Page 10
SPECIFICATIONS*
Channels: 2 (FRS CH1&CH8)
Output Power: 500 mW ERP
Battery Life
Alkaline: 30 - 35 Hours
Power Source: 6.0 V DC
* These specifications are subject to change without notice. They
represent typical values, individual units may vary
Channel Frequencies:
Channel MHz Channel MHz
A (FRS #1) 462.5625 B (FRS #8) 467.5625
The FR-200 can be used with any model FRS radio that
operates on one of the channels above.
-8-
128-5551D
10 of 12
Page 11
90 DAY LIMITED WARRANTY
Applies to Audiovox Family Radio Service Products.
AUDIOVOX CORPORATION (the Company) warrants to the original retail
purchaser of this product that should this product or any part thereof, under
normal use and conditions, be proven defective in material or workmanship
within 90 days from the date of original purchase, such defect(s) will be repaired
or replaced with new or reconditioned product (at the Company's option) without
charge for parts and repair labor.
To obtain repair or replacement within the terms of this Warranty, the product is
to be delivered with proof of warranty coverage (e.g. dated bill of sale),
specification of defect(s), transportation prepaid, to the warranty center at the
address shown below.
The Company disclaims liability for communications range of this product.
This Warranty does not apply to any product or part thereof which, in the opinion
of the Company, has suffered or been damaged through alteration, improper
installation, mishandling, misuse, neglect, accident, or by removal or defacement
of the factory serial number/bar code label(s). THE EXTENT OF THE COMPANY'S
LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR
REPLACEMENT PROVIDED ABOVE AND, IN NO EVENT, SHALL THE
COMPANY'S LIABILITY EXCEED THE PURCHASE PRICE PAID BY
PURCHASER FOR THE PRODUCT.
This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED
WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OFMERCHANTABILITY,
SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY.
ANY ACTION FOR BREACH OF ANY WARRANTY HEREUNDER INCLUDING
ANY IMPLIED WARRANTY OF MERCHANTABILITY MUST BE BROUGHT
WITHIN A PERIOD OF 30 MONTHS FROM DATE OF ORIGINAL PURCHASE.
IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL
OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER
WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER. No person or
representative is authorized to assume for the Company any liability other than
expressed herein in connection with the sale of this product.
AUDIOVOX CORPORATION, 150 MARCUS BLVD., HAUPPAUGE, NEW YORK 11788
1-800-645-4994
128-5385
128-5551D
11 of 12
Page 12
© 1999 Audiovox Corporation, 150 Marcus Blvd., Hauppauge, NY 11788
128-5551D
128-5551D
12 of 12
Loading...