Audiovox DV354 User Manual

MODE

SEL

VOL

MUTE

DV354

Owner’s Manual

Thank You!

Thank you for choosing a JENSEN product. We’ve tried to make the instructions in this owner’s manual clear and easy to follow. If you take a few minutes to look through it, you’ll learn how to use all of the features of your new JENSEN DV354 Mobile Multimedia DVD/CD/MP3 Player for maximum enjoyment.

VIDEO IN 2 L AUDIO IN 2 R

Introduction ..................................................................................................................................... 2

Preparation...................................................................................................................................... 2

Installation...................................................................................................................................... 3

Wiring.............................................................................................................................................. 5

Controls and Indicators ................................................................................................................... 7

Basic Operation ............................................................................................................................. 9

Disc Operation ................................................................................................................................ 9

Setup Menu................................................................................................................................... 13

Disc Symbols and Properties........................................................................................................ 14

Troubleshooting ............................................................................................................................ 15

Specifications ................................................................................................................................ 16

Warranty........................................................................................................................................ 16

DV354

Introduction

Congratulations on your purchase of the JENSEN DV354 Mobile Multimedia DVD/CD/MP3 Player.

Features

• High temperature deck and OPU

• Slot type drive

• Front and rear AV jacks for system expansion

• Din size with mounting brackets included

• LCD display with blue back lighting

• Green back lit buttons

• Dolby digital sound

• IR remote control included

• 12 volt operation

• Compatible with PAL and NTSC DVD (Video CD)

• L/R stereo analog audio outputs for connection to existing head unit aux inputs

• Composite video output

Precautions

• Use the Proper Power Supply. This product is designed to operate with a 12 volt DC, negative ground battery system (the regular system in a North American car).

• Protect the Disc Mechanism. Avoid inserting any foreign objects into the slot of this player. Failure to observe this may cause malfunction due to the precise mechanism of this unit.

• Use Authorized Service Centers. Do not attempt to disassemble or adjust this precision product; contact a professional for assistance.

• Avoi d Moisture. To reduce the risk of fire or electric shock, do not expose this equipment to rain or moisture.

• Use Recommended Accessories: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK AND ANNOYING INTERFERENCE, USE ONLY THE RECOMMENDED ACCESSORIES.

CAUTION: This mobile DVD player is a Class I laser product that uses a visible/invisible laser beam which could cause hazardous radiation exposure if improperly directed. Be sure to operate the mobile DVD player as instructed. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure. Do not open covers and do not attempt to repair the unit yourself. Refer servicing to qualified personnel.

Preparation

It’s a good idea to read all of the instructions before beginning the installation. We recommend having your JENSEN DV354 installed by a reputable installation shop.

Tools and Supplies

You will need these tools and supplies to install your DV354:

• Torx type, flat-head and Philips screwdrivers

• Wire cutters and strippers

• Tools to remove existing radio (screwdriver, socket wrench set or other tools)

• Electrical tape

• Crimping tool

• Volt meter/test light

• Crimp connections

• 18 gauge wire for power connections

• 16 – 18 gauge speaker wire

Disconnecting the Battery

To prevent a short circuit, be sure to turn off the ignition and remove the negative (-) battery cable prior to installation.

NOTE: If the DV354 is to be installed in a vehicle equipped with an on-board drive or navigation computer, do not disconnect the battery cable. If the cable is disconnected, the computer memory may be lost. Under these conditions, use extra caution during installation to avoid causing a short circuit.

DV354

Installation

DIN Front-Mount Installation

1. Use the supplied release keys to remove the half-sleeve from the unit.

2. Install the half-sleeve.

a. Install adapter if necessary (optional).

b. Install half-sleeve into adapter or dashboard using the supplied screws. Do not force the

sleeve into the opening or cause it to bend or bow.

c. Locate the series of bend tabs along the top, bottom and sides of the mounting sleeve.

With the sleeve fully inserted into the dashboard opening, bend as many of the tabs outward as necessary to firmly secure the sleeve to the dashboard.

DVD/ CD / MP3 PLAYER

UTE

CAUTION! Be careful not to damage the vehicle’s wiring.

3. Place the unit in front of the dashboard opening so the wiring can be brought through the mounting sleeve.

4. Complete wiring connections (see “Wiring” on page 5).

5. After completing the wiring connections, turn the unit on to confirm operation (ignition switch must be on). If unit does not operate, recheck all wiring until problem is corrected. Once the unit is properly operating, turn off the ignition switch and proceed with final mounting of the chassis.

6. Carefully slide the DVD player into the half-sleeve making sure it is right-side-up until it is fully seated and the spring clips lock it into place.

NOTE: For proper operation of the CD/DVD player, the chassis must be mounted within 30° of horizontal. Make sure the unit is mounted within this limitation.

7. Attach one end of the perforated support strap (supplied) to the screw stud on the rear of the chassis using the hex nut provided. Fasten the other end of the perforated strap to a secure part of the dashboard either above or below the unit using the screw and hex nut provided. Bend the strap to position it as necessary.

CAUTION! The rear of the unit must be supported with the strap to prevent damage to the dashboard from the weight of the unit or improper operation due to vibration.

8. Replace any items you removed from the dashboard.

DIN Front-Mount Installation

Install Half-Sleeve

ODE

V O

/ C

SEL

/ M

L A

U T

VIDEOIN2 L AUDIOIN 2 R

DV354

DIN Rear-Mount Installation

With some vehicles, you can use the screw holes located on both sides of the unit to fasten the unit to the factory radio mounting brackets supplied with your vehicle. To install this unit using factory mounting plates, perform the following steps:

1. Remove trim ring.

NOTE: The outer trim ring, sleeve and the metal strap are not used for DIN rear-mount installation.

2. Align the screw holes on the bracket with the screw holes on the unit, then tighten the screws (5x5mm) on each side.

3. Reinstall the dash panel.

DIN Rear-Mount Installation

ODE

V O

/ C

SEL

/ M

L A

U T

VIDEOIN2 L AUDIOIN 2 R

Removing the Unit

1. Make sure the ignition is turned off, then disconnect the cable from the vehicle battery’s negative (-) terminal.

2. Remove the metal strap attached the back of the unit (if attached).

3. Lift the top of the outer trim ring then pull it out to remove it.

4. Insert both of the supplied keys into the slots at the middle left and right sides of the unit, then pull the unit out of the dashboard.

Removing the Unit

VOL

DVD/ CD / MP3 PLAYER

MUTE

Reconnecting the Battery

When wiring is complete, reconnect the battery negative terminal.

DV354

Wiring

Power/Accessory Connections

WIRED REMOTE CONNECTOR

1. – Connect to DWR52 wired remote.

P.A.

2. – Connect to PADIN4.

REMOTE CONTROL EXTENDER

3. – Position extender where you are likely to use the remote control. Point remote at eye to control the unit.

CONSTANT POWER WIRE

4. (yellow) – Connect the 12V PLUS constant power wire to a live 12 volt wire in the vehicle. Before making a connection, check that the wire you intend to connect it to is always live, even when the car’s ignition is turned off. If a live wire is not found, route the wire to the car’s fuse block and connect it to a live circuit there.

ACC POWER WIRE

5. (red) – Connect to a +12 volt circuit that is only live when the ignition is on. The best connection point is at the car’s fuse block at the “RADIO” or “ACCESSORY” identified terminals.

GROUND WIRE

6. (black) – Securely fasten the Ground wire to a grounded metal part of the car’s chassis. If you cannot find an existing bolt or screw to fasten it to, drill a hole in the metal and secure it with a screw. To ensure a good ground, remove any paint or grease from areas where the wire will contact the surface.

DC12V OUT

– Provides 12VDC at 300mA when DVD is on.

IR REMOTE CONTROL EXTENDER EYE

POWER WIRING HARNESS

3A FUSE

1A FUSE

YELLOW

BLACK

RED

+ 11 hidden pages