Audiovox Detachable Face Stereo Systems User Manual
InstallationInstructionsforInstallationInstructionsfor
InstallationInstructionsfor
InstallationInstructionsforInstallationInstructionsfor
Detachable Face Stereo SystemsDetachable Face Stereo Systems
Detachable Face Stereo Systems
Detachable Face Stereo SystemsDetachable Face Stereo Systems
CALL TOLL-FREE FOR ANSWERS TO INSTALLATION PROBLEMS
Continental U.S. : 1 - 800 - 645 - 4994
Monday - Friday : 9:00 AM - 7:00 PM Eastern Time
Saturday : 9:00 AM - 5:00 PM Eastern Time
IMPORTANT - RETAIN THIS DOCUMENT FORFUTUREREFERENCE.
Consignes d’Installationdes SystèmesStéréoConsignes d’Installationdes SystèmesStéréo
Consignes d’Installationdes SystèmesStéréo
Consignes d’Installationdes SystèmesStéréoConsignes d’Installationdes SystèmesStéréo
avec Panneau Avant Amovibleavec Panneau Avant Amovible
avec Panneau Avant Amovible
avec Panneau Avant Amovibleavec Panneau Avant Amovible
APPELEZ LE NUMERO VERT POUR TOUTE QUESTION CONCERNANT L’INSTALLATION
Territoire Continental Des E.U. : 1 - 800 - 645 - 4994
Lundi au Vendredi : 9H-19HHeure de la Côte Est
Samedi : 9H-17HHeure de la Côte Est
IMPORTANT -CONSERVERCEDOCUMENTPOURTOUTEREFERENCEULTERIEURE.
Instruccionespara la InstalaciónInstruccionespara la Instalación
Instruccionespara la Instalación
Instruccionespara la InstalaciónInstruccionespara la Instalación
de Sistemas Estereofónicosde Sistemas Estereofónicos
de Sistemas Estereofónicos
de Sistemas Estereofónicosde Sistemas Estereofónicos
con Panel Delantero Desmontablecon Panel Delantero Desmontable
con Panel Delantero Desmontable
con Panel Delantero Desmontablecon Panel Delantero Desmontable
LLAME SIN CARGO PARA FORMULAR PREGUNTAS SOBRE PROBLEMAS DE INSTALACION
Territorio Continental De EE.UU. : 1 - 800 - 645 - 4994
Lunes a Viernes : 9:00 AM - 7:00 PM Zona Horaria del Este
Sabados : 9:00 AM - 5:00 PM Zona Horaria del Este
IMPORTANTE - GUARDE ESTAS INSTRUCCIONES PARA CONSULTARLAS ENELFUTURO.
© 1999 Audiovox Corporation, 150 Marcus Blvd., Hauppauge, N.Y. 11788 Form No. 128-5091A (P-88 / P-94)
INSTALLATION INSTRUCTIONS
UNIVERSAL INSTALLATION PROCEDURE
This unit is designed to fit into a standard DIN dashboard opening of 182 x 52 mm, common in many cars. If
your car does not have an existing opening of this size, it will be necessary to cut or file an opening to these
dimensions. The rear side (without the lip) of the mounting sleeve may be used as a template to cut the required
opening.
Insomecases,aspecialinstallation or adaptor kit may berequiredtoproperlymount the unit. For assistance or answers
toinstallationproblems,callAudiovoxtoll-freeat1-800-645-4994(ContinentalU.S.only,9:00AM-7:00PMEastern
Time Monday-Friday, 9:00 AM-5:00 PM Saturday, Holidays excluded), or consult with your local car stereo
specialist shop.
1. Remove the detachable front panel if it is attached to the chassis by pushing the “Release” button. Slide
the mounting sleeve off of the chassis. If it is locked into position, use the removal tools (supplied) to
disengage it.
2. Check the dashboard opening size by sliding the mounting sleeve into it. If the opening is not large enough,
carefully cut or file as necessary until the sleeve easily slides into the opening. Do not force the sleeve into
the opening or cause it to bend or bow.
3. Check that there will be sufficient space behind the dashboard for the radio chassis.
4. In most installations, it is more convenient to complete the wiring before mounting the radio in the dashboard.
Follow the wiring diagram carefully and make certain all connections of the wiring harness are secure and
insulated with wire nuts or electrical tape to insure proper operation of the unit. After completing the wiring
connections, plug the 16-pin connector into the mating socket on the rear of the chassis, attach the front
panel, and turn the unit on to confirm operation (ignition switch must be “on”). If unit does not operate, recheck all wiring until problem is corrected. Once proper operation is achieved, turn off the ignition switch,
un-plug the wiring harness from the chassis, and proceed with final mounting of the chassis.
5. Locate the series of bend tabs along the top, bottom, and sides of the mounting sleeve. With the sleeve
fully inserted into the dashboard opening, bend as many of the tabs outward as necessary so that the sleeve
is firmly secured to the dashboard.
6. Place the radio in front of the dashboard opening so that the wiring (16-pin connector, antenna lead, RCA
leads if used, etc.) can be brought through the mounting sleeve and plugged into the respective sockets
on the rear of the chassis.
7. Carefully slide the radio into the mounting sleeve making sure it is right-side-up until it is fully seated and
the spring clips lock it into place.
8. Attach one end of the perforated support strap (supplied) to the screw stud on the rear of the chassis using
the hex nut provided. Fasten the other end of the perforated strap to a secure part of the dashboard either
above or below the radio using the screw and hex nut provided. Bend the strap to position it as necessary.
CAUTION: The rear of the radio must be supported with the strap to prevent damage to the dashboard
from the weight of the radio or improper operation due to vibration.
9. Re-attach the front panel to the chassis and test radio operation by referring to the Operating Instructions
for the unit.
REMOVING THE RADIO FROM THE MOUNTING SLEEVE
1. Should it be necessary to remove the radio for servicing or other reasons, first remove the detachable front
panel.
2. Remove the rear support strap by taking off the hex nut securing it to the screw stud on the rear of the chassis.
3. Use the removal tools (supplied) to disengage the side spring clips and pull the radio out of the mounting sleeve.
-1-
Form No.128-5091A
Loading...