Page 1
To PRESET RADIO STATIONS
You can tune in a stored station directly by pressing DIRECTORY/PRESET
button.
10 stations on FM band can be preset.
10 stations on AM (MW) band can be preset.
1. Slide the FUNCTION switch to RADIO.
2. Press the BAND button to select a band and tune the TUNING
or button to choose a desired station.
3. Press the PGM button, “MEMORY” indicator will blink on the display.
4. Press the DIRECTORY/PRESET –/+ button to select desired number.
5. Press PGM button again to store the preset station.
6. Repeat steps 2 to 5 until the desired station are presetted (up to 10
stations).
TUNING IN A PRESETTED STATION
Press the DIRECTORY/PRESET –/+ button to select a presetted number.
After pressing the button, the presetted number (such as “P01”) is displayed
2 seconds, then the frequency is displayed.
The “MEMORY” indicator is displayed during the preset tuning.
FOR BETTER RECEPTION
FM : To improve FM reception,
extend the antenna.
Note : After listening, slide the FUNCTION switch to OFF.
NOTE:
While the reception is strong stereo broadcast, the “ ” icon will
appear on the display.
AM : To improve AM (MW)
(MW)
reception, rotate the unit.
-7- -8-
CARE & MAINTEN ANCE
GENERAL GUIDELINES
• Do not touch the laser lens on the CD player.
• Temperature changes can cause condensation to form on the laser lens.
If condensation forms on the lens, leave the disc compartment door
open (without disc) for an hour to remove condensation.
• Exposure to direct sunlight or extreme heat (such as inside a car parked
in the sun) can cause damage or malfunction.
• To prevent dust from reaching internal parts, keep the compartment door
closed when not using (except when necessary to remove condensation).
HANDLING THE COMPACT DISC
It's important that you periodically clean the laser lens:
1. Turn off the unit's power and disconnect the AC
power.
2. Open the CD door and remove the disc.
3. Clean the lens with a soft cloth or use an air blower
brush designed for cameras.
4. If you still are not able to remove dirt particles, moisten
a cotton swab with isopropyl alcohol and gently
apply to the face of the laser lens, rubbing gently
until all traces of dirt are removed.
Although the music tracks in the disc are covered with a
protective layer, it is still advisable to treat the disc
carefully. Always pick up discs by the edge and put them
back in their holders immediately after use.
CLEANING THE UNIT
Do not use volatile chemicals on this unit. Clean by lightly wiping with a soft
cloth.
IMPORTANT NOTICES:
• Should the CD door be opened before the reading of the CD is completed,
a jamming noise may occur. This can be resolved by closing the CD door
and then sliding the FUNCTION switch temporarily to OFF.
• If an abnormal display indication or an operating problem occurs, discon-
nect the AC power cord and remove the batteries. Wait at least 5 seconds,
then reconnect the AC power cord or reinstall the batteries.
Laser lens
PORTABLE CD SYSTEM
OPERATING INSTRUCTION
The lightning flash
and arrowhead
within the triangle is
a warning sign
alerting you of
"dangerous voltage"
inside the product.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NO T EXPOSE
THIS APPLIANCE T O RAIN OR MOISTURE.
WARNING: TO REDUCE THE
RISK OF ELECTRIC SHOCK, DO
NOT REMOVE COVER (OR
BACK) NO USER-SERVICEABLE
PARTS INSIDE. REFER
SERVICING TO QUALIFIED
SERVICE PERSONNEL.
CLASS 1 LASER PRODUCT
CLASS 1 LASER
PRODUCT
This product contains a low power laser device.
INVISIBLE LASER RADIATION WHEN
OPEN AND INTERLOCKS DEFEATED .
CAUTION
AV OID EXPOSURE T O BEAM
The exclamation
point within the
triangle is a warning
sign alerting you of
important instructions
accompanying the
product.
TROUBLE SHOOTING TIPS
Should any problem persistes after you have made the following checks,
consult your nearest service faciility.
CD / MP3
Problems
System does not turn on
Disc in place but unit
won't play
RADIO
Problems
Poor FM reception
Poor AM(MW) reception
Solutions
• Make sure AC power plug is secure in
the outlet and inlet has power.
• Batteries may be dead. Install new
batteries.
• Make sure the FUNCTION switch is
set to CD position.
• Make sure disc is clean and
undamaged.
• Make sure printed side of disc is facing
up.
• Make sure PAUSE mode is not
activated.
• Make sure the unit is on a secure spot.
Vibration or jarring can cause the disc
to skip.
Solutions
• Electrical interference in your home
can cause poor reception. Move the
unit away from them (especially those
with motors and transformers).
• Reposition or turn the unit for better
reception.
SPECIFICATIONS
GENERAL
Power consumption: 15 W
Power source: AC 120V~60 Hz (USA and Canada)
AC 220V ~50Hz (China)
AC 220V ~60Hz (Korea)
AC 230V~50 Hz (Europe and Hong Kong)
AC 240V~50 Hz (Australia)
AC 110-120V/220-240V~50/60Hz (Others)
DC 9V (6 x "C" size or UM-2 batteries)
Specifications are subject to change without notice.
SAFETY PRECA UTIONS
Follow the advice below for safe and appropriate operations.
ON PLACEMENT
• Do not use the unit in places which are extremely hot, cold, dusty or
humid.
• Place the unit on a flat and even surface.
• Do not restrict the air flow of the unit by placing it in a place with poor
air flow, by covering it with a cloth, or by placing it on a carpet.
ON SAFETY
• When connecting and disconnecting the AC cord, grip the plug and not
the cord itself. Pulling the cord may damage it and create a hazard.
• When you are not going to use the unit for a long period of time,
disconnect the AC power cord.
ON AC VOLTAGE
• Before use, check that the rated voltage of your unit matches your
local voltage.
• When there is condensation inside the unit, the unit may not function
normally.
• Let it stand for 1 to 2 hours before turning the power on, or gradually
heat the room up and dry the unit before use.
FCC INFORMATION (for USA)
This device complies with part 15 of FCC Rules. Operations are subject to
the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including
interference that may cause undesirable operations.
-9- -10-
Should any trouble occur, disconnect the AC power cord and refer
servicing to qualified personnel.
RATING PLATE LOCATION
The rating plate location is on the bottom of product.
Printed in China 811-136191-033
Page 2
NAMES OF CONTROLS
3.0
1
2
3
4
5
6
7
8
9
10
15
16
1. FUNCTION selector
2. VOLUME control
3. PHONE jack
4. Handle
5. CD door
6.
Directory/Preset + button
7.
Directory/Preset – button
8. PROGRAME button
9. PLAY MODE button
10. DISPLAY
11. SKIP/SEARCH/TUNING
button
12. SKIP/SEARCH/TUNING
button
13. STOP/BAND button
14. PLAY/PAUSE button
15. Telescopic antenna
16. AC socket
-1- -2- -3-
11
12
13
14
POWERING UP
AC POWER
You can power your portable stereo system by plugging the detachable
AC power cord into the AC inlet on the back of the unit and into a wall
AC power outlet.
Check that the rated voltage of your unit
matches your local voltage. Make sure that
the AC power cord is fully inserted into the
unit.
Caution: (for North America)
To prevent electrical shock, match wide
blade of plug to wide slot, fully insert.
Note : When not being used on mains the
AC Cord should be unplugged from the unit.
BATTER Y POWER
Insert 6 "C" size batteries in the battery compartment. Be sure that the
batteries are inserted correctly to avoid damage to the unit.
• Always remove the batteries when unit will not be used for a long
period of time, as this will cause leakage of the batteries and
subsequently damage to your unit.
• Playback would automatically come to a stop when the batteries
have no more power. Replace all the batteries with new ones.
• Do not mix old and new batteries. Do not mix ALKALINE, standard
(CARBON-ZINC) or rechargeable (NICKEL-CADMIUM) batteries.
1.5V 1.5V
1.5V 1.5V
1.5V 1.5V
n
m
n
To AC inlet
To wall AC outlet
m
3.0
ADJUSTING THE SOUND
VOLUME
Adjust the VOLUME control of the stereo system to a desired level.
FOR PRIVATE LISTENING
Connect headphones (Ø 3.5 mm stereo mini-plug) to the PHONES
jack.
When headphones are connected, speakers automatically disconnected.
CD PLA YBA CK
1. Slide the FUNCTION switch to CD, and then " " is shown
on the display.
2. Open the Disc door. Place a CD in the center with the label side up
and then close the Disc door gently. The total number of tracks will
show on the display.
3. Press the PLAY/PAUSE button to start play.
• Adjust the VOLUME.
TO STOP PLAYBACK
• Press the BAND button to stop disc play.
TO INTERRUPT PLAYBACK
• Press the PLAY/PAUSE button while a CD is playing to pause play
(the " " indicator will blink).
• Press the PLAY/PAUSE button again to resume play.
TO SEARCH A TRACK
• You can search a track in playback mode.
• In stop mode, the display will show the total number of tracks.
Press either one of the SKIP/SEARCH or button according to the
desired direction to search a track. Each press skips one track. During
play , the first press on the skip bac kwards
of the current track.
REPEAT PLAY -- In play mode
This function allows one track or all tracks on a disc to be pla yed repeatedly.
button will go to the beginning
TO REPEAT THE SAME TRACK
• Press the PLAY MODE button once during playback, the repeat one
" " indicator will blink.
TO REPEAT THE WHOLE DISC
• Press the PLAY MODE button a second time to repeat all tracks, the
repeat all " " indicator appears on the display.
TO CANCEL REPEAT PLAY
• Press the PLAY MODE button until the “ ” indicator is turned off.
RANDOM PLAY - Only in stop mode
• Press the PLA Y MODE button in stop mode until “RANDOM” indicator
appears on the display, and then press the PLAY/PAUSE button to
start play. It can play all tracks without sequence.
• To locate the next track: press SKIP/SEARCH button. However,
you can not locate a previous track even if you keep SKIP/SEARCH
button pressed.
MP3 PLAYBACK
TO PLAY MP3
This set can read MP3.
1. Slide the FUNCTION switch to CD. " " is shown on the
display.
2. Open the Disc door. Place a MP3 disc in the center with the label
side up and then close the Disc door gently. The total number of
albums and the “MP3” indicator appear on the display.
3. Press the PLAY/PAUSE button to start play.
4. Press the BAND button to stop playback.
5. In stop mode, press PLAY/PAUSE button to start playback.
TO SEARCH AN ALBUM
Basically this system supports the album search mode to search an album
at high-speed.
1. Press the DIRECTORY/PRESET +/– button to search a desired album
in play/stop mode.
2. After selected a desired album, the number of this album is displayed
2 seconds, then the number of the first track or the total tracks of this
album is displayed.
-4-
3. Press SKIP/SEARCH or button to search a desired track and then
press the PLAY/PAUSE button to play the track.
4. During searching the album, the album number is shown on the displa y.
REPEAT PLAY- In play/stop mode
This function allows one track, all tracks or albums on a disc to be played
repeatedly.
TO REPEAT THE SAME TRACK
• To repeat the same track, press the PLAY MODE button during play
until the " " appears on the display and the “ “ indicator will
blink.
TO REPEAT THE SAME ALBUM
• To repeat the same album, press the PLAY MODE button during play
until " ALBUM " appears on the display.
TO REPEAT THE WHOLE DISC
• Press the PLAY MODE button during play until " " appears on
the display.
TO CANCEL REPEAT PLAY
• Press the PLAY MODE button until the REPEAT indicator is disappear.
RANDOM PLAY - Only in stop mode
• Press the PLA Y MODE button in stop mode until “RANDOM” indicator
appears on the display, and then press the PLAY/PAUSE button to
start play. It can play all tracks of a album without sequence.
• To locate the next track: press SKIP/SEARCH button. However,
you can not locate a previous track even if you keep SKIP/SEARCH
button pressed.
PGM (Programe) PLAY
PROGRAM PLAY (IN STOP MODE)
1. For CD : Press the PGM button until “MEMORY” and “00” blink on
the display.
For MP3 : Press the PGM button until “MEMORY” and “000” blink on
the display.
2. Press DIRECTORY/PRESET button to select an album (in mp3 mode).
3. Press the SKIP/SEARCH or button to select the desired track.
4. Press the PGM button to store a track.
-5- -6-
5. Repeat steps 2 and 4 until all the desired track are programmed (up to
20 tracks).
6. Press the PLAY/PAUSE button to start play . During program playbac k,
“MEMORY” indicator will blink.
TO PLAY PROGRAMMED TRACKS
After storing the desired tracks, press the PLAY/PAUSE button to play
the programmed tracks.
TO CHECK THE PROGRAM
Press PGM button during programming before you press PLAY/PAUSE
button.
Each time PGM button is pressed the previously stored track number
appears on the display.
Note : In MP3 mode, will display the album number two seconds, then
display the track number of this album.
TO STOP PROGRAM PLAY
Press the BAND button to stop playback.
TO CLEAR THE PROGRAM
Press the BAND button twice, open the Disc door or slide the
FUNCTION switch to RADIO or OFF to clear the program.
RADIO OPERA TION
You can listen to your favourite radio stations by sliding the FUNCTION
switch to RADIO, and then
1. Press the BAND button to choose AM(MW) or FM.
2. Press the TUNING or button to choose a desired station.
• Adjust the VOLUME.
TO TUNE FASTER
Hold down the TUNING or button. While the button is being held,
the frequency will change faster.
TO SEARCH FOR A STATION QUICKLY (AUTO Search)
Keep the TUNING or button pressed until the tuner starts searching
for a station. After finding a station the search stops.
To stop the Auto Search manually, press the TUNING or button.
The Auto Search may not stop at stations with very weak signals.
Loading...