PORTABLE CD SYSTEM
OPERATION INSTRUCTION
I RISK ~ ~~ SHOCK I
~~:~~~~
The lightning flash and WARNING: TO REDUCETHE RISK OF
[arrowhead within the
\triangle is a warning sign COVER (OR BACK) NO USER-
alerting you of "dangerous SERVICEABLE PARTS INSIDE.
voltage" inside the product. REFER SERVICING TO OUALIFIED
This product contains a low power laser device.
I ELECTRIC SHOCK, 00 NOT REMOVE
SERVICE PERSONNEL
I The exclamation point within
the triangle Is a warning sign
alerting you of important
Instructions accompanying
the product.
SAFETY PRECAUTIONS
Follow the. advice below for safe and appropriate operations.
ON PLACEMENT
.Do not use the unit in places which are extremely hot, cold, dusty or
humid.
.Place the unit on a flat and even surface.
.Do not restrict the air flow of the unit by placing it in a place with poor air
flow, by covering it with a cloth, or by placing it on a carpet.
""'.0",=
ON SAFETY
.When connecting and disconnecting the AC cord, grip the plug and not
the cord itself. Pulling the cord may damage it and create hazard.
.When you are not going to use the unit for a long period of time, disconnect
the AC power cord.
ON AC VOLTAGE
.Before use, check that the rated vQltage of your unit matches your local
voltage.
.When there is condensation inside the unit, the unit may not function
normally-
.Let it stand for 1 to 2 hours before turning the power on, or gradually heat
the room up and dry the unit before use.
FCC INFORMATION
This device complies with part 15 of FCC Rules. Operations are subject to
the following two conditions: .
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesirable operations.
Should any trouble occur, disconnect the AC power cord and refer servicing
to qualified personnel.
PRINTED IN CHINA
811-128391-010
NAMES OF CONTROLS
.="'-=
17
18
USING THE CD PLA YER
1. Set the FUNCTION switch to
CD. "- -" is shown in the dis-
play.
FUI\K;nON
CD DISPLAY
2. Open the CD door .Place a disc
in the center with the label side
up and then close the CD door
gently. The total number of
tracks will show in the display.
~
~
,
",
I
~
B
3. Press PLAY/PAUSE button (H)
to start CD play. The Play /
PAUSE indicator will light.
.Adjust the VOLUME.
! All! PlAY
a3a-..,D~ ,-,PAUSE
TO INTERRUPT PLAYBACK
.Press ( ~II )PLAY/PAUSE button
while a CD is playing to pause
play (the PLAY/PAUSE indicator
will blink).
V(I-18IE
,
c '-:::-1
.ALL .PlAY
&8: ':: DIE ':: PAUSE
~
TO STOP PLA YBACK
.Press ( .) STOP to stop disc play.
.Press ( ~II )PLAY/PAUSE again
to resume play.
0]
.AU. .ptAy
mm;:,DNE ;:,PAtH
dn 9NI}I~MOd
POWERING UP
t
m
~
16 61
\.
AC POWER
You can power your portable stereo
system by plugging the detachable AC
power cord into the AC inlet on the
back of the unit and into a wall AC
power outlet.
Check that the rated voltage of your
unit matches your local voltage.
Make sure that the AC power cord is
fully inserted into the unit.
Caution: To prevent electrical shock,
match wide blade of plug to wide slot,
fully insert.
BAnERY POWER
Insert 8 "C" size batteries in the
,
~
battery Compartment. Be sure that the
batteries are inserted correctly to avoid
damage to the unit. Always remove
the batteries when unit will not be
used for a long period of time, as this
will cause leakage to the batteries and
subsequently damage to your set.
ADJUSTING THE SOUND
,, """--co:-;
PROGRAM PLAY (IN STOP MODE)
;-:-:
~'
",.
t'
~j
~
'1
.'
-..
"i;
~;
J-'
!
1
&;
'1:,
".
~
RADIO OPERA TION
.=~-~
-:'
"
~
;f
Note: After listening, set the FUNCTION switch to TAPE.
I
TO CLEAR THE PROGRAM
.Set the FUNCfION switch to TAPE or RADIO.
OR
.Open the CD door (during stop mode).
REPEAT PLAY (IN PLAY MODE)
This function allows one track, all tracks on a disc or the programmed tracks
only to be played repeatedly.
Note: After listening, set the FUNCTION switch to TAPE.
USING THE CASSETTE COMPARTMENT
""'""~
CARE & MAINTENANCE
TROUBLE SHOOTING TIPS
,,"0'==
..;
}C;
~'
0;;
SPECIFICATION
,,{
~.
A-~-,=..,,~
Loading...