Audiovox AX-2K4MS, AX-2K4S, AX-2K4, AX-2K4MSFL User Manual

Model AX-2K4 AX-2K4S, AX-2K4MS, & AX-2K4MSFL
Transmitter Programming Guide
These transmitters makes use of icons (symbols) to identify the reac­tion your security system/keyless entry/and or remote start system, where applicable, will have when any icon (button) is pressed. These icons are programmed at time of installation to meet the needs of the individual and to complement the vehicle that the system is installed in. To replace a transmitter or add transmitters, please follow the programming instructions listed on the pages of this manual.
BUTTON
RECEIVER CHANNEL
1
2
1
3
3
4
5
Lock And Arm Alarm, also initiate and terminates *Panic
Unlock And Disarm, also initiates and terminates *Panic. Programmable to unlock drivers door and or all doors.
Lock and arm/unlock and disarm. May be programmed to unlock driver's door or all doors. Also will initiate and terminate *Panic.
Pulsed or switched output to control Remote Trunk Release or optional device connected to channel 3.
When pressed and release two times, will provide pulsed output or activate the Remote Start option when installed.
When so equipped, this button can be used to operate an optional device connected to channel 4.
When so equipped, this button can be used to operate an optional device connected to channel 5.
SYSTEM FUNCTION
* Where So Equipped
128-6987
1 of 6
Some of the more popular options available for the unused Option Buttons of your transmitter are:
AS 9554 Remote Garage Door Interface AS 9075 Remote car starter AS 9153 Remote window roll up AS 9256 Remote trunk release relay
Although the most common use of the transmitter buttons are shown on the front page of this guide, any button or button combination can be programmed into any receiver channel. Additionally, if all 4 buttons are used and you require access to a 5th channel, you would program a combination of buttons to control the 5th function. i.e... You have programmed lock for arm, unlock for disarm, trunk for trunk release, and Opt1 for garage door operation, and you've added a window up module that you want independent control of, you would program un­lock and trunk buttons pressed simultaneously into the receiver to con­trol this function independently. Also, if you do not program a transmit­ter button into channel 2 which is the separate unlock/disarm chan­nel, then whatever button is programmed into channel 1 will serve as both lock/arm & unlock/disarm.
PROGRAMMING TRANSMITTERS: NOTE: It is important to remember that during the programming mode,
each individual step must be completed within 15 seconds of the previous step. If the 15 second time limit expires between steps, the unit will automatically exit the program mode. This
is indicated by a long chirp from the siren. Non alarm models will flash the parking lights only to confirm the transmitter code has been learned and stored. NOTE: Because the system may be capable of sounding a siren, the
vehicle horn, or both, where the siren chirp is referenced be-
low, the siren may chirp, the horn may beep, or both devices
may sound.
TO PROGRAM ADDITIONAL TRANSMITTERS:
1) Enter the vehicle, and turn the ignition switch to the on position.
2) Press and release the valet push button switch three times.
3) The dash mounted LED will flash 1x, and the siren will chirp 1x, indicating that the system is ready to accept programming of channel #1 which is arm/lock, disarm/unlock/unlock 2, and panic functions.
4) Press and hold the lock or lock/unlock symbol button of the transmit­ter you wish to program for 4 seconds or until a long chirp is heard from the siren.
"Repeat step 4 for each transmitter you wish to program". NOTE: If your transmitter button has the Lock/Unlock icon on one
button, press and release the valet push button switch 2 times then move on to step #8.
5) Press and release the valet push button switch one time to advance to
2
128-6987
2 of 6
Loading...
+ 4 hidden pages