Audiovox AVXMTG10UA Installation Manual

10.1-Inch LED Backlit LCD Roof-Mount DVD Player

With DVD/CD/MP3 SYSTEM

AVXMTG10UA

INSTALLATION

GUIDE

TABLE OF CONTENTS

Important Notices �� 2 IR Transmit and Receive Modes M1 or M2) ��3 Materials Included in this Package �� 4 Removing and Installing Snap On Covers �� 5 General Vehicle Installation Approach ��8 Connecting the Dome Lights ��11

IMPORTANT NOTICES

Installation of overhead products requires careful planning and preparation� Be extremely careful when working on a vehicle with side curtain air bags� Do not route wires near any portion of the side curtain air bag assemblies� This includes anchor points in A, B, C or D pillars of the vehicle� Routing wires in these areas or running wires by the side curtain air bags can prevent the side curtain air bag from fully deploying which can result in personal injury to vehicle occupants� If you have any question regarding routing in a vehicle, please contact Audiovox Technical support at 1-800-225-6074�

An LCD panel and/or video monitor may be installed in a motor vehicle and visible to the driver only if the LCD panel or video monitor is used for vehicle information, system control, rear or side observation or navigation� If the LCD panel or video monitor is used for television reception, video or DVD play, the LCD panel or video monitor must be installed so that these features will only function when the vehicle is in “park” or when the vehicle’s parking brake is applied�

When connecting power and ground in a mobile video installation, insure that the ACC wire is fused at the point where it is connected to the vehicle’s ACC wiring� Failure to do so can result in damage to the vehicle if a short circuit develops between the vehicle connection point and the mobile video product�

An LCD panel and/or video monitor used for television reception, video or DVD play that operates when the vehicle is in gear or when the parking brake is not applied must be installed to the rear of the driver seat where it will not be visible, directly or indirectly, to the operator of the motor vehicle�

*** Important Notice***

When installing this overhead monitor there should be no obstructions such as extra cabling, power chokes or any other objects placed between this overhead and supplied mounting bracket� Failure to comply may cause damage to the overhead monitor and will void the warranty�

WARNINGS

• Do not use any solvents or cleaning materials when cleaning the video monitor�

• Do not use any abrasive cleaners, they may scratch the screen�

• Use only lightly dampened lint free cloth to wipe the screen if it is dirty�

• Lock the LCD screen in fully closed position when not in use�

• Before putting on headphones, always adjust the volume setting to OFF or lowest position�

• Remember to leave the dome light switch in the oﬀ or auto position when the vehicle is unattended, as the dome lights, if left on, can drain the vehicle battery�

• Do not put pressure on the screen�

• Caution children to avoid touching or scratching the screen, as it may become dirty or damaged�

Safety Precautions

For safety reasons, when changing video media, it is recommended that the vehicle is not in motion, and that you do not allow children to unfasten seat-belts to change video media or make any adjustments to the system� System adjustments can be accomplished using the remote control, while seat-belts remain fastened� Enjoy your AUDIOVOX entertainment system but remember that the safety of all passengers remains the number one priority�

Licensed under one or more of the following patents, Patent Numbers 5,775,762, 5,927,784, and 6,678,892�

IR TRANSMIT AND RECEIVE MODES M1 OR M2

The AVXMTG10UA has an option that allows the user to select from two IR transmit and receive modes (M1 or M2)� This feature can be used when two AVXMTG10UA units are installed in the same vehicle or if the vehicle has an RSA (Rear Seat Audio) that uses “A” channel headphones� When in the M1 mode the unit will transmit audio on the A channel� When in the M2 mode the unit will transmit audio on the B channel� If two of these units are used in one vehicle it may help to mark one remote with M1 on the back and the other remote with M2 on the back� A unit set to M2 mode will not work with a remote control programmed to the M1 mode� Conversely a unit set to M1 mode will not work with a remote control programmed to the M2 mode� To change from M1 to M2 mode, point the remote control towards the IR receiver on the AVXMTG10UA� Press and hold the M2 button for 5 to 7 seconds� The following screen will be displayed:

Note: The OSD will appear on the screen for 4 – 5 seconds� To change from M2 to M1 mode, point the remote control towards the IR receiver on the AVXMTG10UA� Press and hold the M1 button for 5 to 7 seconds� The following screen will be displayed:

Note: The OSD will appear on the screen for 4 – 5 seconds When the AVXMTG10UA is powered up in DVD mode it will display the following screen showing FM Modulator status and FM channel selection as well as IR Transmitter status (IR ON or IR OFF) and which mode (M1 or M2) the unit is in�

+ 11 hidden pages