Audiovox APS-597 User Manual

Model APS-597

Owner’s Manual

4 Button Remote Security System

IMPORTANT !

system is equipped with selectable manual override circuitry. It is possible that you will need
to manually override your security system if the transmitter becomes lost, or inoperative due
to battery failure. Reading the sections on "MANUALLY OVERRIDING YOUR SYSTEM" is
necessary to fully understand the procedure required to enable your vehicle in such
situations. In addition, the chart on the last page of this manual has a section for the particular
features and options installed in your vehicle as well as the override method selected.

Valet Switch manual override is pre-selected from the factory,

can be configured for "Custom Code" operation. Confirm the override mode selected on the
last page of this manual, and familiarize yourself with the selection on it's operation.

FEATURES :

w 1 Five Button Programmable RF Transmitters

w 1 Five Button Programmable Transceiver

w Five Channel Receiver (Capable Of Accepting Up To 4 Transmitters)
w Code Hopping Technology
w Selectable Manual Override Mode
w Remote Panic in all modes
w Protected Valet
w User Programmable Manual Override Code
w 7 Function LED (Light Emitting Diode) - Arm / Disarm / Zone 1, 2, 3 / Valet / Arming
w Intrusion Alert with Memory
w Audible Arm / Disarm / Defective Zone / Tamper Confirmation
w Instant Siren Activation
w Starter Disable
w Additional Engine Immobilizer Output (optional relay required)
w True Last Door Arming (hardwire only)
w Defective Zone By-Pass
w Hardwire or Voltage Sense Selectable
w Active or Passive Arming Selectable
w Programmable Auto Lock On / Off
w Programmable Auto Unlock On / Off
w Programmable Door Lock Pulse Duration 1 Second / 3.5 Seconds/1 Sec L/ Dbl. U/L
w Programmable Active or Passive Door Locks
w User Programmable Permanent Chirp Delete
w On Command RF Chirp Delete from Transmitter
w 6 Tone Multi Tone Siren
w RF Inhibit with ignition on
w Parking Light Flasher
w Plug In Dual Stage Shock Sensor

OPTIONS:

w Remote Trunk Release ( must have electronic trunk release )
w Remote Keyless Entry ( must have power door locks )
w Multiple Vehicle Capable
w Remote Starter
w Remote Power Window Roll Up
w Remote Garage Door Interface
w Two Step Unlock Configurable
w Headlight Illumination During Arming, Disarming, Or Both

with Dual Stage Shock Sensor

In order to provide the highest possible level of security to your vehicle, this

however, the system

Page 1

128-7406

1 of 16

YOUR “ Code Hopping “ TRANSMITTERS

The transmitters included with your new security system use the most ad­vanced and secure form of radio frequency transmission available on any
current automotive security system. Some of today’s sophisticated auto
thieves use a device known as a code grabber, which will receive and store
the signal from your keychain transmitter, and retransmit at a later time to
disarm your system.
Y our anti code hopping transmitters will change their signal every time the
button is pressed, so when a thief grabs then retransmits your signal, the
alarm system
If your transmitter button is pressed more than fifty times while it is out of
range of the vehicle ( children playing with your keys ), the transmitter will
not operate when you return to the vehicle and will need to be realigned to
the receiver. To do this, simply press the lock button two times within a one
second time period. The system will now respond to that transmitter each
time a button is pressed.
NOTE: Your system has the option of using a siren, the vehicle horn, or both

Y our System is also packaged with a two way confirming transmitter

beeps.

2) Press the Trunk/Key button until Homepage Select Set appears.

3) Press "F" to display the selections of text or icons.

4) Use the Trunk/Key or Option buttons to toggle between text or icon
modes.

5) Use the "F" key to select.

6) Press the "F" button for 5 seconds to exit the program mode.
Other features that are selectable or programmable on your two way

transmitter are:
(a) Alarm Trigger History (Will display the last 4 trigger events)
(b) Y ou can assign a Name for a output channel function
(c) Y ou can personalize the Homepage to display name, or have the digital

clock displayed

will not

respond.

for the sounding device. Where the siren is referenced below, the
horn or both may in fact chirp, or beep.

shown left which can be set for Icon mode or text mode to
indicate the function and status of your vehicle.

To change modes, press and hold the "F" button for 5
seconds. This puts the transmitter into the program mode.
The program modes lets you make selections by pressing
the Trunk/Key Icon button to scroll up, or the Option button
to scroll down. Once you come to the selection of choice,
press the "F" button to select the option, and then use the
Trunk/Key , Option, or lock/unlock buttons to toggle between
choices.

Example: To change between text or icon modes, do the
following:

1) Press the "F" button for 5 seconds until the transmitter

Page 2

128-7406

2 of 16

(d) Y ou can select Icon Mode or Text mode
(e) Y ou can select Language of text from English, Spanish or French
(f) Set the temperature readout to display in "Fahrenheit or Celsius
(Available on certain model remote start units)
(g) Set the melody for the Alarm Clock
(h) Y ou can set the unit to provide a Tone, or Vibrate upon activation
(i) Y ou can set the Countdown Timer
(j) You can set the Alarm Clock
(k) You can set the Clock

Y our transmitter has a battery indicator that is shown in the upper right
corner of the screen as shown below. This icon indicates a new

battery shown with 3 bars. As the battery deteriorates, the bars will
disappear. 1 bar indicates the battery should be replaced. Replace battery
with a fresh 1.5V AAA battery and dispose of the used battery properly .

Other icons that will be displayed at times when certain functions and

features are active in the vehicle or on the remote:
Range Indicator. The range indicator will have bars to the side of the

icon if the unit is out of range.
Vibrate Mode On, this icon will be displayed if you select vibrate

instead of tones. Locate vibrate/tone select in the transmitter program

section and set for vibrate.
Alarm Clock. This icon will be toggled on and off when the "F" +

Trunk/Key buttons are pressed simultaneously. The feature must be
set in the feature selection menu of the transmitter.

Count Down Timer . This icon is toggled on and off by pressing the "F"
+ Option buttons simultaneously . The feature must be set for a time in

the feature selection menu of the transmitter.
Parking Meter Count Down Timer .
The transmitter has a built in timer that can count down from 10, 20, 30,

60, 90, or 120 minutes. This feature is useful when parking the vehicle in a
metered parking lot. If the time on the parking meter is 30 minutes, you
can set the count down timer to 20 minutes. The transmitter will emit a
beep tone when the timer expires to remind you to get back to your vehicle.
To use the parking meter timer, Press the "F" + Option buttons more than
one time. Once activated the Count Down Timer as described above.
Activating the "F" + Option a second time will set the parking meter count
down to 10 minutes, a third time will set it to 20 minutes, a fourth time will
set it to 30 minutes, etc... up to 120 minutes, then the cycle will repeat,
countdown activation, 10 minutes, 20 minutes and so on. Once you stop
at a setting, the unit will count down and when it reaches the set time will
alert you with a beep tone as a reminder that you have to get back to the
vehicle.

Page 3

128-7406

3 of 16

Power Save Feature. Press the "F" and Lock buttons simultaneously to
toggle this feature on and off. With this mode on, the battery in the

transmitter will go into a power down mode when the unit is disarmed.

24 Hour start Timer . This icon is displayed when the 24 hour start timer

is activated. Press the option+lock buttons simultaneously for 3

second. The transmitter will beep and display the 24 hr timer. The vehicle
will start automatically when the time set is reached. (See chart for time

toggle this feature on of off, from the Locked/Armed mode, press the Option
and Lock buttons simultaneously . (Only available on certain remote start
models).

Throughout this manual you will find screen shots where they apply if using
the two way transmitter. If using the one way transmitter while the two way
transmitter is within range of the vehicle, the two way transmitter will update
it's screen.

the preferred setting.

settings). Pressing this button combination a second time
will toggle this feature off. Note the transmitter must be within
range of the vehicle to set this feature and within range to
cause the vehicle to start at the preset time. The unit will
start at the prescribed time once only . This function must be
selected each time you want the vehicle to start. T o activate
this function, (a) Turn the ignition switch off. (b) Within 10
seconds of step (a), depress and hold the brake pedal, while
pressing the key icon transmitter button 2 times. (c) the unit
will emit 2 chirps, the transmitter will beep and the start timer
icon on the display will remain on. (Only available on certain

remote start models).

T emperature Start Mode. This icon will appear when the

temp start mode is activated. The vehicle will start one
time automatically when the temperature reaches 0*. Caution,
Be certain vehicle is outside before activating this mode. T o

When the Lock button on the transmitter is pressed and the
command is received and acted upon by the unit in the vehicle,
the vehicle doors will lock and the alarm system will arm. The two
way transmitter, if within range of the vehicle, will beep once, and
display locked and armed either in text or by icons dependent on

When the Unlock button on the transmitter is pressed and the
command is received and acted upon by the unit in the vehicle,

The two way transmitter, if within range of the vehicle will beep twice. And
display unlocked and disarmed in text or by icons dependent on the
preferred setting.

the vehicle doors will unlock and the alarm system will disarm.

When the Trunk button on the transmitter is pressed for three seconds
and the command is received and acted upon, if the trunk release

Page 4

128-7406

4 of 16

option is installed, the vehicle's trunk will open. The two way transmitter, if within
range, will display the trunk opened in text or by the icon as shown.

ARMING THE SYSTEM - ACTIVE

1. Turn off the engine, exit the vehicle and close all doors, hood lid and trunk lid.

2. Press and release the Lock button on the keychain transmitter.

þ Dash mounted LED begins to flash slowly.
þ Parking Lights flash one time.
þ Siren sounds one chirp.

If the siren/horn sounds 3 chirps, then you have left a door, trunk, or hood lid ajar.
Simply close the opened entry point to provide full protection. If the siren "chirped"
three times, sometime after arming, the exclusive delayed dome light learn circuit
has been programmed and the system detected a open entry point after the
learned delay expired. Again, closing the hood, trunk, or doors will correct the
problem and you do not need to disarm the system to make the correction. If the
siren/horn did not sound when arming, then the chirps have been turned off and
you should refer to the section titled "ELIMINA TING THE ARM/DISARM CHIRPS" in
this manual.

o Doors Lock - Optional
o Headlight Illumination - Optional

SILENT ARMING - ACTIVE (Must be activated during programming)

1. Turn off the engine, exit the vehicle, and close all doors, hood lid, and trunk lid.

2. Press and hold the Lock button on the keychain transmitter for 2 seconds.

þ Dash mounted LED begins to flash slowly.
þ Parking Lights flash one time.
þ Siren will not sound.

If the siren "chirped" three times, sometime after arming, the exclusive delayed
dome light learn circuit has been programmed and the system detected a open
entry point after the learned delay expired. Closing the hood, trunk, or doors will
correct the problem and you do not need to disarm the system to make the correc­tion.

o Doors Lock - Optional
o Headlight Illumination - Optional

ARMING THE SYSTEM - P ASSIVE ( AUTOMATIC ) (Must be activated during pro­gramming)

1. Turn off the engine, exit the vehicle, and close and lock all doors, hood lid and
trunk lid.
þ Dash mounted LED begins to flash rapidly, indicating 30 second passive
arming has begun.

2. Opening any protected entry point during the 30 second passive arming cycle
will immediately suspend automatic arming and the 30 second passive
arming cycle will restart when all doors are closed. At the end of the passive
arming cycle;
þ Dash mounted LED begins to flash slowly.

Page 5

128-7406

5 of 16

þ Parking Lights flash one time.

If the siren did not sound when arming, then the chirps have
been turned off, and you should refer to the section titled
"ELIMINATING TH E ARM / DISARM CHIRPS" in this manual.
o Doors Lock - Optional
Door locking during passive arming is a selectable feature.
The alarm can be programmed to allow the doors to lock only
when arming using the keychain transmitter and they will not
automatically lock during passive arming.

PROTECTION WHILE THE SYSTEM IS ARMED

þ Opening any protected door, hood, or trunk lid will cause the alarm to
immediately sound. The alarm will continue to sound for 30 seconds, then stop
and continue to monitor all protected entry points. If the thief left a door opened, the
alarm will sound for six 30 second cycles, remain armed and ignore that triggered
zone.
þ Whenever the system is armed, the dash mounted LED indicator will slowly
flash. This serves as a visual deterrent to the potential thief. The LED is a very low
current bulb and will not cause the vehicle’s battery to drain, even when left unat­tended for extended periods.
þ Whenever the system is triggered, the vehicle’s parking lights will flash for the
full 30 second alarm cycle, attracting visual attention to the vehicle.
þ Optional - Whenever the system is armed, the vehicle’s starting circuit will be
bypassed. If the thief should choose to ignore the siren, the vehicle can not be
started.
þ Any mild impact to the vehicle’s glass will cause the alarm to sound a short
series of warning tones.
þ Any strong impact to the vehicle’s glass will cause the alarm to trigger for the full
30 second alarm cycle.

Whenever the system is armed and then triggered from either entry point or any
additional sensor device, the two way transmitter, if within range, will display the
entry point in text or by icon dependent on the preferred setting.

Note: Upon trig- ger, the hand held
unit can be se- lected to vibrate or
mimic the sound of the siren.
Some of the trig- gered displays are shown below.

þ Siren sounds one chirp

1. As you approach the vehicle, press and release the Unlock button on the key­chain transmitter.

þ Dash mounted LED turns off.
If passive arming was selected during the installation, then the LED will start

DISARMING THE SYSTEM

Page 6

128-7406

6 of 16

flashing rapidly, indicating that the system is re-arming automatically. Open any
door to suspend the automatic arming.
þ Parking Lights flash two times.
If the parking lights flashed three times, then the alarm was triggered in your
absence. Before turning the key on, examine the LED to identify which zone was
triggered.
þ Siren sounds two chirps.
If the siren sounds 4 chirps, then the alarm was triggered in your absence. Before
turning the key on, examine the LED and refer to the INTRUSION WARNING
SIGNALS section of this manual to identify which zone was triggered.
If the siren did not sound when disarming, then the chirps have been turned
off, and you should refer to the section titled “ELIMINATING THE ARM /
DISARM CHIRPS“ in this manual.
o Doors Unlock - Optional
Note: If the optional 2 step door unlock circuit is installed, when the unlock
transmitter button is activated, the drivers door only will unlock, pressing the
unlock button a second time will cause all doors to unlock. If your transmitter has
a separate lock unlock buttons, pressing the unlock button anytime after the first
unlock command will cause all the vehicle doors to unlock.
o Headlight Illumination - Optional

SILENT DISARMING (Must be activated during programming)

1. As you approach the vehicle, press and hold the Unlock button on the keychain
transmitter for 2 seconds.

þ Dash mounted LED turns off.
If passive arming was selected during the installation, then the LED will start
flashing rapidly, indicating that the system is re-arming automatically. Open any
door to suspend the automatic arming.
þ Parking Lights flash two times.
If the parking lights flashed three times, then the alarm was triggered in your
absence. Before turning the key on, examine the LED to identify which zone was
triggered.
þ Siren will not sound.
If the siren sounds 4 chirps, then the alarm was triggered in your absence. Before
turning the key on, examine the LED and refer to the INTRUSION WARNING
SIGNALS section of this manual to identify which zone was triggered.
o Doors Unlock - Optional
Note: If the optional 2 step door unlock circuit is installed, when the unlock
transmitter button is activated, the drivers door only will unlock, pressing the
unlock button a second time will cause all doors to unlock. If your transmitter has
a separate lock/unlock buttons, pressing the unlock button anytime after the
first unlock command will cause all the vehicle doors to unlock.
o Headlight Illumination - Optional

WHILE THE SYSTEM IS SOUNDING

If during a triggered state, you wish to shut off the siren without disarming your
security system, simply press and release any transmitter button other than the

Page 7

128-7406

7 of 16

disarm button. This action will turn off the siren yet leave the vehicle fully armed
and protected. This feature is particularly useful if you are aware of children play­ing near your vehicle that may accidently trigger your security system. In this case
you can cancel the siren sounding without disarming your alarm.

INTRUSION WARNING SIGNALS

This system will inform you if an intrusion attempt has occurred while you were
away from the vehicle. If an intrusion attempt has occurred, the siren will chirp 4
times and the parking lights will flash 3 times when disarming the system. Enter
the vehicle and observe the dash mounted LED to identify which zone was trig­gered.

 If the LED is flashing one time...pause...one time...pause...etc., then an

intrusion attempt was made to the shock sensor, or an accessory
triggering device that may have been added to the system.

 If the LED is flashing two times...pause...two times...pause...etc., then an

intrusion attempt was made to a hood or trunk pin switch that was added
to the system, or to a light activated entry point if the alarm was installed
using the voltage sensing feature.

 If the LED is flashing three times...pause...three times...pause...etc., then

an intrusion attempt was made through one of the vehicle’s doors.

These intrusion warning indicators are stored in the system’s memory and will

ing the manual override sequence.

1. From the disarmed condition, turn the ignition key to the on position.

2. Press and hold the valet pushbutton switch until the dash mounted LED, turns

on. The LED will remain on as long as the system is in valet mode.

3. To return to normal operation, press and release the push button switch any

time the ignition is on.

NOTE: Always remember to return the system to the NON VALET mode, after

servicing, to ensure that the vehicle remains protected at all times.

Page Call Out:
From within the vehicle, if the valet push button is pressed for three seconds,
the alarm unit in the vehicle will transmit to the LCD remote and a beep tone will
be heard and a phone icon will be displayed on the hand held transmitter
indicating that someone is calling you to the vehicle.

only be erased when the ignition key is turned on.
VALET SWITCH The valet switch allows you to temporarily by­pass all alarm functions, eliminating the need to hand your trans­mitter to parking attendants or garage mechanics. When the
system is in valet mode, all alarm functions are bypassed, how­ever the remote panic feature and remote door locks will remain
operational. To use the valet mode, the system must first be
disarmed either by using your keychain transmitter, or by operat-

MANUALL Y OVERRIDING YOUR SYSTEM:
USING THE V ALET SWITCH MANUAL OVERRIDE

Your Security System can be disarmed without the use of the keychain transmitter.
This is necessary, since you will need the ability to operate your vehicle if the
transmitter is lost or its battery fails. If your system has been selected for Valet

Page 8

128-7406

8 of 16

Switch manual override as indicated on the last page of this manual, to by-pass
the alarm system.

1. Open the vehicle door. The alarm will sound.

2. Turn the ignition key to the on position.

3. Within 5 seconds, press and release the valet push button switch.
The alarm system will stop sounding and enter the disarmed mode. You can now
start and operate the vehicle normally.
Typically this override mode is used only if the transmitter has become inoperative.
Y ou may elect to enter the VALET mode until repair or replacement of the transmitter,
after which, returning the system to the full operation mode is necessary. To do
so, see item 3 under the heading VALET SWITCH.

PROGRAMMING YOUR CUSTOM CODE OVERRIDE:

Unlike override switches easily found, and defeated, this security system allows
the consumer to program a personal override code, offering a higher level of
security. To take advantage of this option, programmable feature # 10 must be
selected for the Custom Code Option. Consult your installation center for
programming details. The system comes from the factory with a pre-programmed
override code of 11. To change this default override code, do the following:

1. Disarm the system by use of the transmitter, or by use of the emergency
override sequence. Turn the ignition switch to the on position.

2. Within 10 seconds, press and release the valet/override switch, 3 times.

3.Within 10 seconds turn the ignition switch off, on, off, on, off, on.
(The siren or horn will beep and the lights will flash one time.)

4. Within 10 seconds, begin to enter your chosen 10ths digit by pressing and
releasing the pushbutton switch from 1 up to 9 times.

5. Within 10 seconds of the last entered 10ths digit, turn the ignition switch off
then on.

6. Within 10 seconds, begin to enter your chosen units digit by pressing and
releasing the pushbutton switch from 1 up to 9 times.

7.Finish by turning the ignition switch to the off position.

If the new code was accepted, the unit will report back the newly entered code, by
flashing the LED, first indicating the 10ths digit, pause and then the units digit.
The unit will report the new code three times with a one second pause between
each code, then the system will begin arming. If the LED flash pattern reports the
previously stored code, the new code was not entered correctly. Please repeat
steps 1 through 7 above considering the following.
NOTE: Acceptable digits 10ths or units are 1 through 9. The unit will not recognize

a 0 (Zero), or no digit entered in any place, units or tenths.

NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for

more then 5 seconds during any of the above steps, the unit will revert
back to the last successfully stored code.

Custom Code Programming Example:

To Change the code from the factory pre-assigned code of 11 to “52” you would do
the following:

1. Disarm the system by use of the transmitter, or by use of the emergency
override sequence.

Page 9

128-7406

9 of 16

2. Turn the ignition switch to the on position.

3. Within 10 seconds, press and release the valet/override switch, 3 times.

4. Within 10 seconds turn the ignition switch off, on, off, on, off, on.
(The siren or horn will beep and the lights will flash one time.)

5. Within 10 seconds, begin to press and release the push button switch to set
the tenths digit.
(As per the example, press and release 5 times to set the tenths digit to 5)

6. Within 10 seconds of the last press of the pushbutton, turn the ignition switch
off then on.

7. Within 10 seconds, begin to press and release the push button switch to set
the units digit.
(As per the example, press and release 2 times to set the units digit to 2).

8. Turn the ignition switch to the off position. Immediately observe the LED flash
pattern.

You will note the LED flashing five times, pause, and then flash two times, pause.
This pattern will be repeated three times indicating the new code (52) has been
accepted and stored in memory.
NOTE: If after step 8, the LED flashes a code other than what was just entered, this

indicates that the code has not been changed. You will have to repeat

steps 1 through 7 above being certain to note the following:
Acceptable digits 10ths or units are 1 through 9. The unit will not recognize a 0
(Zero), or no digit entered in any place, units or tenths.
NOTE: If 15 seconds of inactivity expire, or if the ignition switch is turned off for more

then 5 seconds during any of the above steps, the unit will revert back to the
last successfully stored code.

MANUALL Y OVERRIDING YOUR SYSTEM:
USING THE CUSTOM CODE OVERRIDE

Assuming the override code programmed has not been changed, and the default
override code of 11 is in the system's memory.

1) Enter the vehicle and turn the ignition switch to the on position.
Note: The siren will sound.

2) Within 5 seconds, press and release the pushbutton switch 1 time.

3) Within 5 seconds, turn the ignition switch off then on.

4) Within 5 seconds, press and release the pushbutton switch 1 time.

5) Turn the ignition switch off then on and start the vehicle.
Note: If you have changed the programmed override code then substitute your

new code tenths for step 2 above, and units for step 5 above.

ELIMINA TING THE NORMAL ARM / DISARM CHIRPS

As explained earlier in the manual, you can eliminate the chirps selectively any
time you arm or disarm the system, if the feature has been activated, simply by
holding the ARM / DISARM button for two seconds. If you find the normal arming
and disarming chirps annoying, they can be turned off permanently, eliminating the
need to hold the ARM / DISARM button for two seconds. To do this,

1. Turn the ignition key on then off.

2. Within 10 seconds, press and release the valet push button switch three
times.

3. If the chirps were on before you started, then you will hear 2 chirps indicating
they have been turned off.

Page 10

128-7406

10 of 16

If the chirps were off before you started, then you will hear one chirp indicating they
have been turned on.
NOTE: Whenever the chirps are by-passed, the 4 chirp intrusion indicator and 3

chirp defective zone indicator will always operate. Since these are important
warnings to you that something has happened, they cannot be eliminated.

REMOTE PANIC OPERA TION

on the keychain transmitter for 3 or more seconds. The alarm will immediately
sound.

2. T o stop the alarm, press and hold the ARM or DISARM button on the transmitter
again for 3 seconds. If the button is not pressed, the alarm will automatically
stop after 30 seconds. Also if any transmitter button other than the ARM or
DISARM button is pressed and released, the Panic mode will be turned off
immediately. The normal function of this transmitter button will be suspended
during the Panic sounding period.

3. During the panic mode, the Lock and Unlock buttons can be used to lock and
unlock the doors, (if the option is installed), however once the unlock/disarm
button is pressed, the vehicle's starter inhibit device, (where installed) will be
disabled allowing the vehicle to start.

NOTE: While in the Panic mode, pressing and releasing the ARM or DISARM

buttons will, if the option is installed, lock and unlock the doors respectively.
While in the panic mode, anytime the DISARM button is pressed, the panic
feature will continue for the allotted 30 seconds, however, the security
system will be disarmed allowing the vehicle to start.

The ARM or DISARM button on your keychain
transmitter also functions as a panic switch for
use in emergency situations. To use remote
panic,

1. Press and hold the ARM or DISARM button

ADDITIONAL REMOTE FUNCTION ( CHANNEL 3 )

when the appropriate transmitter button is depressed for 4 seconds. Although
this output is intended to activate the trunk release option, any other optional
devices may be connected to this channel. Consult your installation center for
more information about this output.

ADDITIONAL REMOTE FUNCTION ( CHANNEL 4 )

Trunk/Key Button
Other Transmitter button configurations are also available. Con-

sult your installation center for other configurations not listed above
that may have been programmed to operate a specific feature of
your system.

This security system is equipped with an output which will activate

This security system has an additional feature that can be con­nected to a number of different optional accessories. Some of the
more common uses for this channel are:
o Remote Trunk Release o Remote Car Starter

Page 11

128-7406

11 of 16

o Remote Window Closure

To activate the optional accessory, press the programmed button on the keychain
transmitter for up to 8 seconds for continuous output, or press and release for
momentary activation. The optional accessory will immediately engage. Check
with your installation center for more information on the optional accessory that
may have been installed and how it is accessed.

o Remote Garage Door Interface

ADDITIONAL REMOTE FUNCTION ( CHANNEL 5 )

To activate the optional accessory, press the programmed button on the keychain
transmitter for up to 8 seconds for continuous output, or press and release for
momentary activation. The optional accessory will immediately engage. Check
with your installation center for more information on the optional accessory that
may have been installed and how it is accessed.

IGNITION CONTROLLED LOCK UNLOCK: (Unlock Drivers Only, or Unlock All Doors)
Your security system has a selectable safety feature that allows the vehicle doors
to lock when the ignition switch is turned on, (Providing all doors are closed), and
to unlock the doors when the ignition switch is turned off. In addition, the unlocking
of the doors is further selectable, in a two step unlock configuration, to unlock only
the drivers door or all doors.

TELEMATIC UPGRADE:

This system has the ability to have a telematic upgrade module connected to it.
This is a upgrade that can give you control of certain functions of your vehicle from
a Telephone, or in some cases a computer interface. Please check with your
installation center for most recent Telematic Upgrades. If you had a Telematic
Upgrade installed, the manual supplied with the upgrade unit will provide a op­erators manual advising of the features of the system and means available to
control these features of your vehicle.

This security system has an additional feature that can be
connected to a number of different optional accessories. Some
of the more common uses for this channel are;

o Remote Trunk Release o Remote Car Starter
o Remote Window Closure
o Remote Garage Door Interface

Page 12

128-7406

12 of 16

THIS P AGE LEFT BLANK INTENTIONALL Y

Page 13

128-7406

13 of 16

SYSTEM FUNCTIONS A T A GLANCE

DASH LED INDICAT ORS

RAPID FLASHING = PASSIVE ARMING
SLOW FLASHING = ARMED
OFF = DISARMED
ON SOLID = VALET MODE
3 FLASH...PAUSE = INTRUSION ZONE 3
2 FLASH...PAUSE = INTRUSION ZONE 2
1 FLASH...PAUSE = INTRUSION ZONE 1

SIREN CHIRP INDICATORS

*1 CHIRP = ARM
*2 CHIRPS = DISARM
3 CHIRPS = ARM / DOOR OPENED
4 CHIRPS = DISARM / INTRUSION

* These chirps are optional, and can be de - activated.

PARKING LAMP INDICA T ORS

1 FLASH = ARM
2 FLASHES = DISARM
3 FLASHES = DISARM / INTRUSION

APS-597

Your System Has These Features Activated

o Starter Disable
o Remote Keyless Entry
o Auto Lock with ignition key
o Auto Unlock with ignition key
o Passive Arming
o No Lock in passive mode
o Hardwire doors, hood, and trunk
o Custom Code Override
o Valet Switch Override

Page 14

128-7406

14 of 16

THIS P AGE LEFT BLANK INTENTIONALL Y

Page 15

128-7406

15 of 16

© 2005 Audiovox Electronic Corporation, 150 Marcus Blvd., Hauppauge, N.Y. 11788

Page 16

128-7406

16 of 16

128-7406