®
AOM701
7” FLAT PANEL COLOR OBSERVATION
MONITOR OWNER'S MANUAL
UDIOVOX
PECIALIZED
A
B
+
–
AOM701 Features:
– 7” High Performance Color LCD
– Built-in Audio Speaker with Volume Control
and 12V Trigger
–2 Camera (A/V) Input with A/B Select Control
– Backlit Controls and Day/Night Picture Modes
for Nighttime Use
– Auto/Manual Power On
– Sun Visor Included
PPLICATIONS, L.L.C.
Visit us at http://www.asaelectronics.com
e 4
Patent Pending
Important! – Please Read This Manual Before Installing!
Congratulations on your purchase of a Voyager AOM701 LCD Observation Monitor.
With proper installation and use, your AOM701 is designed to provide you with years
of trouble-free operation. This manual contains important information required to
properly install and operate the unit. Please read this manual thoroughly before
beginning.
All Voyager Observation products are strictly intended to be installed as a supplement
aid to standard rear-view mirror systems that may already exist in your vehicle.
Voyager observation products are not intended for use as substitutes for rear-view
mirror devices, or for any other standard motor vehicle equipment required to be
installed on vehicles by law.
While Voyager observation products contribute to improving the vehicle operator’s
field of view, these products are no substitute for proper defensive driving techniques
and observance of traffic laws and motor vehicle safety regulations.
Warnings!
Installation Location
It is unlawful in most jurisdictions for a person to drive a motor vehicle equipped with
a television viewer or screen located at any point forward of the back of the driver’s
seat or in any location that is visible, directly or indirectly, to the driver while
operating the vehicle. The AOM701 product is designed to be used primarily as a rear
observation device in conjunction with closed circuit cameras. In any installations
where the AOM701 is used to display television broadcasts or recorded video
playback, installation location must adhere to local laws and regulations.
Tampering
To prevent electrical shock, DO NOT OPEN THE MONITOR CASE. There are
potentially harmful voltages inside the monitor. There are no user serviceable parts
inside. If evidence of tampering is detected, the warranty will be considered void.
Moisture
Your Voyager AOM701 was designed to be water-resistant. While it will withstand
short periods of exposure to moisture, this product does contain sensitive electronic
components and exposure to moisture should be limited by the user / installer. This
product is not designed for applications where constant exposure to moisture or
immersion can be encountered. This unit should NEVER be cleaned with a power
washer or used where direct power washer spray may be encountered.
2
90 DAY/ 12 MON TH LIM ITE D WAR R ANT Y
PA C K I N G C ON T E NT S:
WA R RA NT Y CAR D
QT Y . 1
SPL IT G ROM ME T
1” O.D. 3/16 I .D.
QT Y . 1
L CD M ONI TOR
QT Y . 1
5’ INT E RM EDI ATE HA RNE SS
QT Y . 1
POW ER HA R NES S QT Y . 1
1 • 1 •
2 • 2 •
3 • 3 •
4 • 4 •
DI ST ANC E M AR K ER
ST IC K ER
STO P
STO P
QT Y .1
• • •
• • •
• • •
• • •
SU N SH IE LD
QT Y . 1
#8 X ¾” SEL F DRI L L B L AC K SCR EW S
(H AR DWA R E B AG )
CO NNE CT ION CA BL E
4” X 2” V EL CR O
QT Y .4
#10 X 5/16” PHP TH RE AD
FOR MI NG BL A CK SC RE W
(H AR DWA R E B AG )
QT Y . 4
QT Y .1
QT Y . 1
4” BL AC K W IR E T I E
QT Y . 4
3
CONTROLS AND OPERATION
A
B
1 2 3 4 5
+
–
1. Power/Stand-By Button
The Power / Stand-by Button has two possible operations modes.
a. Manual mode - Turned on manual by the user by pressing the Power #1
button.
b. Stand-by mode - Turned on by a stand by trigger wire generally connected
to the vehicles 12V reverse backup lights.
Manual Mode wiring - For manual mode operation, the AOM701 should be
wired as follows:
ACC (+12V) Red wire should be connected to the vehicles accessory feed.
GND - ground wire should be connected to chassis ground.
Standby Mode wiring - For Standby mode operation, the AOM701 should be
wired as follows:
ACC (+12V) Red wire should be connected to the vehicles accessory feed.
GND - ground wire should be connected to chassis ground.
Standby / Reverse trigger blue wire should be connected to the reverse feed
of the vehicles backup lighting system.
The power button #1 features dual illumination. It will be brighly lit when the
unit is turned on and will be dimly lit when the unit is turned off.
When the unit is turned on all other buttons will be illuminated. When off only
the Power button will be lit.
* Note: Please note that when the unit is in the standby mode, trigger wire is
triggered, the Power button #1 will not function.
4