Audiovox AMP-610 User Manual
Model AMP-610
500 Watt Stereo Amplifier
OwOw
Ow
OwOw
ManualManual
Manual
ManualManual
nene
ne
nene
r'sr's
r's
r'sr's
INDEX
Specifications .............................................................................1
Precautions ................................................................................2
Installation Instructions ................................................................3
Controls and Indicators.............................................................4 - 7
Wiring Instructions .......................................................................7
4-Channel and Mixed -Mono Input Wiring Diagram .........................8
4-Channel and Mixed -Mono Output Wiring Diagram ......................9
3-Channel Input Wiring Diagram ..............................................10
3-Channel Output Wiring Diagram Wiring Diagram .......................11
2-Channel Mono (Bridged) Input Wiring Diagram ...................12
2-Channel Mono (Bridged) Output Wiring Diagram ...................13
Warranty .........................................................................................14
HIGH PERFORMANCE STEREO AMPLIFIER
This power amplifier has been designed to provide high quality performance with a
minimum of maintenance. However, it's performance will only be as good as the care
and quality of components with which it is installed. We therefore advise that you read
these instructions very carefully to familiarize yourself with the product and it's
features.
Should you require assistance with the installation or wiring of this unit, please call
our toll-free "HELP" line at 1-800-645-4994 during the days/hours shown.
SPECIFICATIONS
HELP!
1-800-645-4994
Monday - Friday
Saturday
8:30am - 7:00pm Eastern
9:00am - 5:00pm Eastern
Maximum Output Power
4-Channel Operation: 125 watts x 4
2-Channel Operation: 500 watts x 2
Output Power @ 1% T.H.D.
4-Channel Operation: 600 watts RMS x 4
2-Channel Operation: 120 watts RMS x 2
Output Impedance: 2 - 8 ohms (stereo)
4 - 8 ohms (mono)
Frequency Response: 10 - 50,000 Hz. ± 1 dB
Channel Separation: 55 dB
* Due to continuing improvement, Audiovox reserves the right to change features and design without notice.
Signal / Noise Ratio: 90 dB (A-Weighted)
Input Impedance: low-level 10K ohms
high-level 100 ohms
Input Sensitivity: low-level 200 mv. - 5 v.
high-level 2 - 10 v.
Supply Voltage: 12 volts, negative ground
Fuse Rating: 20 amps.
Dimensions (W x H x D): 9" x 2-1/4" x 10-5/8"
230 mm x 57 mm x 270 mm
-1-
PRECAUTIONS
1. Although this unit is designed with built-in self-protection circuits, there may be a possibility of damage if it is not wired
correctly. Please follow the wiring instructions carefully for the type of system being used.
2. The last lead to be connected is the wire to the positive (+) terminal of the battery. Connect this wire only after having
completed and checked all other connections to the amplifier.
3. By nature of its design, a power amplifier generates heat and requires good air circulation around it to dissipate that
heat. Do not install the amplifier in an enclosed area which does not permit adequate air circulation. Should the
temperature of the unit rise too high, the internal thermal sensors will shut off operation until it has cooled down
sufficiently.
4. If fuse replacement is necessary, use only fuses of the same ampere rating as originally supplied with the unit. The
use of fuses with incorrect ratings may cause serious damage to the amplifier. If fuses blow consistently, carefully
check all electrical connections to the unit.
5. Supply of adequate battery voltage is critical to the proper operation of the power amplifier. The leads to the battery
and chassis ground
#16 gauge wire or thicker (smaller gauge #) for the battery and ground leads.
must be of a thick enough gauge to provide this voltage to the amplifier. We recommend
6. Make certain that the speaker(s) to be used with this amplifier are capable of handling the output power (wattage)
of the unit. Use of speaker(s) not rated for the output of this amplifier may cause damage to or failure of the
speaker(s) for which Audiovox will not be liable.
-2-
INSTALLATION INSTRUCTIONS
1. Select a mounting area where the amplifier will
have sufficient air circulation for proper cooling.
Inadequate air circulation will cause the temperature
of the amplifier to rise and will trigger the
thermal protection mode.
2. Place the amplifier on the mounting surface
and mark the locations of the four mounting
holes as shown in the illustration.
3. Remove the amplifier and drill a 1/8" hole at
each of the four locations.
CAUTION: Before drilling the holes, look at the
underside of the mounting surface. Always
check carefully to avoid drilling into wiring,
braces, fuel or brake lines.
YOU DRILL !
CHECK BEFORE
INSTALLATION DIAGRAM
4. Secure the amplifier to the mounting surface
using the self-tapping screws provided.
-3-
Loading...