Audiovox ACD-27 User Manual

Download

Page 1

WNER'S MANUWNER'S MANU

WNER'S MANU

WNER'S MANUWNER'S MANU

ALAL

AND INSTAND INST

AND INST

AND INSTAND INST

LOC

BAND/LOUD

MODE

MONO

MUTE

PAU SCN RPT SHF

AS/PS

ACD-27ACD-27

ACD-27

ACD-27ACD-27

AM/FM/MPX RADIO

WITH DETACHABLE FRONT PANEL

COMPACT DISC PLAYER,

ALLAALLA

ALLA

ALLAALLA

321456

TION GUIDETION GUIDE

TION GUIDE

TION GUIDETION GUIDE

T/F

VOL

SEL

VOL

POWER

Released 2-28-03.

CD CHANGER CONTROLS

AND QUARTZ CLOCK

128-6691

1 of 16

Page 2

INSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONS

This unit is designed for installation in cars, trucks, and vans with an existing radio opening. In many cases, a special installation kit will be required to mount the radio to the dashboard. These kits are available at electronics supply

IONSIONS

IONS

stores and car stereo specialist shops. Always check the kit application before purchasing to make sure the kit

works with your vehicle. If you need a kit but cannot find it available, call our toll-free “HELP” line (1-800-645-4994).

UNIVERSAL INSTALLATION PROCEDURE USING MOUNTING SLEEVE

1. Remove the detachable front panel if it is attached to the chassis by pushing the “Release” button. Slide the mounting sleeve off of the chassis. If it is locked into position, use the removal tools (supplied) to disengage it.

2. Check the dashboard opening size by sliding the mounting sleeve into it. If the opening is not large enough, carefully cut or file as necessary until the sleeve easily slides into the opening. Do not force the sleeve into the opening or cause it to bend or bow. Check that there will be sufficient space behind the dashboard for the radio chassis.

3. Locate the series of bend tabs along the top, bottom, and sides of the mounting sleeve. With the sleeve fully inserted

ION INSTRUCION INSTRUC

ION INSTRUC

into the dashboard opening, bend as many of the tabs outward as necessary so that the sleeve is firmly secured

to the dashboard.

4. Place the radio in front of the dashboard opening so that the wiring can be brought through the mounting sleeve. Follow the wiring diagram carefully and make certain all connections of the wiring harness are secure and insulated

ALLALL

ALL

with wire nuts or electrical tape to insure proper operation of the unit. After completing the wiring connections, attach the front panel and turn the unit on to confirm operation (ignition switch must be “on”). If unit does not operate, re-check all wiring until problem is corrected. Once proper operation is achieved, turn off the ignition switch and

INSTINST

INST

proceed with final mounting of the chassis.

5. Carefully slide the radio into the mounting sleeve making sure it is right-side-up until it is fully seated and the spring clips lock it into place.

6. Attach one end of the perforated support strap (supplied) to the screw stud on the rear of the chassis using the hex nut provided. Fasten the other end of the perforated strap to a secure part of the dashboard either above or below the radio using the screw and hex nut provided. Bend the strap to position it as necessary.

CAUTION: The rear of the radio must be supported with the strap to prevent damage to the dashboard from the

7. Re-attach the front panel to the chassis. Establish a location for the remote input jack (usually the underside of the dashboard) if it is a feature of the radio. Anchor it in place using two self-tapping screws (M5x6). Do not over-tighten screws. Test radio operation by referring to the Operating Instructions for the unit.

INSTALLATION USING KITS

1. If your vehicle requires the use of an installation kit to mount this radio, follow the instructions included with the installation kit to attach the radio to the mounting plate supplied with the kit.

2. Wire and test the radio as described in Step 4 above.

3. Install the radio/mounting plate assembly to the sub-dashboard according to the instructions of the installation kit.

4. Attach the support strap to the radio and dashboard as described in Step 6 above.

5. Replace the dashboard trim panel.

ISO INSTALLATION PROCEDURE

This unit has threaded holes in the chassis side panels which may be used with the original factory mounting brackets of some Toyota, Nissan, Mitsubishi, Isuzu, Hyundai and Honda vehicles to mount the radio to the dashboard. Please consult with your local car stereo specialist shop for assistance on this type of installation.

1. Remove the existing factory radio from its dashboard or center console mounting. Save all hardware and brackets as they will be used to mount the new radio.

2. Carefully un-snap the plastic frame from the front of the new radio chassis. Remove and discard the frame.

3. Remove the factory mounting brackets and hardware from the existing radio and attach them to the new radio.

CAUTION: DO NOT EXCEED M5 X 6 MM MAXIMUM SCREW SIZE.

4. Wire the new radio to the vehicle as per step 4 of the Installation Instructions.

5. Mount the new radio assembly to the dashboard or center console using the reverse procedure of step 1.

weight of the radio or improper operation due to vibration.

LONGER SCREWS MAY TOUCH AND DAMAGE COMPONENTS INSIDE THE CHASSIS.

128-6691

2 of 16

Page 3

OLL-FREE INSTOLL-FREE INST

OLL-FREE INST

OLL-FREE INSTOLL-FREE INST

The installation and wiring connections for this unit are so simple, we doubt you'll need our help, but, if you do, we're here to help you. Just call our toll-free telephone assistance line at 1-800-645-4994 during the days and hours shown (U.S.A. and Canada only).

DAY

MON. - FRI. SATURDAY

NUT (5MM)

SCREW (5MM)

NUT (5MM)

FASTEN THIS END TO SECURE PART OF DASHBOARD. DRILL HOLE IF NECESSARY.

FOR PROPER OPERATION OF THE CD PLAYER, THE CHASSIS MUST BE MOUNTED WITHIN 20° OF HORIZONTAL. MAKE SURE THE UNIT IS MOUNTED WITHIN THIS LIMITATION.

SIDE VIEW

CHASSIS

PACIFIC

5:30AM - 4PM 6AM - 2PM

UNIVERSAL INSTALLATION USING MOUNTING SLEEVEUNIVERSAL INSTALLATION USING MOUNTING SLEEVE

UNIVERSAL INSTALLATION USING MOUNTING SLEEVE

UNIVERSAL INSTALLATION USING MOUNTING SLEEVEUNIVERSAL INSTALLATION USING MOUNTING SLEEVE

PERFORATED STRAP

FASTEN THIS END TO SCREW STUD ON REAR OF CHASSIS

MOUNTING SLEEVE

CAUTION:

20° MAX.

FRONT PANEL

ALLALL

ALL

ALLALL

MOUNTAIN

6:30AM - 5PM

7AM - 3PM

EXISTING DASH OPENING FILE EDGES TO FIT IF NECESSARY - DO NOT OVERFILE NOTE: IF DASH IS SOLID, USE REAR SIDE (WITHOUT THE LIP) OF MOUNTING SLEEVE AS A TEMPLATE & CUT OPENING

SCREW STUD

ION ASSISTION ASSIST

ION ASSIST

ION ASSISTION ASSIST

7:30AM - 6PM

8AM - 4PM

RADIO

REMOVAL TOOLS

CENTRAL

NCENCE

NCE

NCENCE

EASTERN

8:30AM - 7PM

9AM - 5PM

BEND TOP TABS UPWARD

BEND BOTTOM TABS DOWNWARD

DETACHABLE FRONT PANEL

INST

INSTINST

ALL

ALLALL

AA T

TT ION INSTRUC

ION INSTRUCION INSTRUC

TT IONS

IONSIONS

ISO INSTALLATIONISO INSTALLATION

ISO INSTALLATION

ISO INSTALLATIONISO INSTALLATION

REMOVE THE PLASTIC FRAME FROM THE FRONT OF THE CHASSIS BY CAREFULLY UN-SNAPPING IT.

UN-SNAP AT 2 PLACES EACH ON TOP AND BOTTOM

PLASTIC FRAME

MAXIMUM

SCREW SIZE

M5 x 6

FACTORY MOUNTING BRACKETS

TYPICAL INSTALLATION

MAXIMUM

SCREW SIZE

M5 x 6

128-6691

3 of 16

Page 4

DIO WIRINGDIO WIRING

DIO WIRING

DIO WIRINGDIO WIRING

REFER TO PAGE 5 FOR SPEAKER WIRING

ANTENNA

AUTOMATIC ANTENNA

RADIO WIRING

EXISTING ANTENNA CABLE

BLUE

IMPORTANT

THE BLUE WIRE CAN BE USED TO REMOTELY ACTIVATE AN AUTOMATIC ANTENNA OR AN EXTERNAL AMPLIFIER (SEE ANTENNA OR AMPLIFIER MANUAL)

0.5 AMP FUSE

BLACK

15 AMP FUSE

YELLOW WIRE MUST BE CONNECTED AS SHOWN OR RADIO WILL NOT OPERATE PROPERLY

RED

SCREW

METAL PART OF DASH (DRILL HOLE IF NECESSARY)

YELLOW

IMPORTANT

4-PIN PLUGS

FUSEBLOCK

“RADIO” FUSE +12V ACCESSORY

CAR BATTERY

POSITIVE (+) TERMINAL 12 VOLT BATTERY

ANTENNA LEAD ON REAR OF RADIO

RADIO

9 PIN PLUG (SEE PAGE 5 FOR SPEAKER WIRING)

128-6691

4 of 16

Page 5

SPESPE

SPE

SPESPE

REFER TO PAGE 4 FOR RADIO WIRING

ER WIRINGER WIRING

ER WIRING

ER WIRINGER WIRING

RCA LINE OUT JACKS FOR USE WITH OPTIONAL EXTERNAL AMPLIFIERS

RED=RIGHT REAR WHITE=LEFT REAR

9-PIN PLUGS

SPE

SPESPE

THE AMPLIFIERS IN THIS RADIO ARE ONLY DESIGNED FOR USE WITH 4 SPEAKERS.

NEVER COMBINE (BRIDGE) OUTPUTS FOR USE WITH 2 SPEAKERS.

NEVER GROUND NEGATIVE SPEAKER LEADS TO CHASSIS GROUND.

FAILURE TO WIRE EXACTLY AS SHOWN BELOW MAY CAUSE ELECTRICAL DAMAGE TO THE RADIO.

RADIO

WARNING!

4-PIN PLUGS

AA K

KK ER WIRING

ER WIRINGER WIRING

LEFT FRONT SPEAKER

WHITE w/BLACK STRIPE

GREEN w/BLACK STRIPE

WHITE

GREEN

SEE PAGE 4 FOR RADIO WIRING

GRAY w/BLACK STRIPE

GRAY

VIOLET

VIOLET w/BLACK STRIPE

RIGHT FRONT SPEAKER

HELP!

1-800-645-4994

Monday - Friday

LEFT REAR SPEAKER RIGHT REAR SPEAKER

Saturday

8:30am - 7:00pm Eastern 9:00am - 5:00pm Eastern

128-6691

5 of 16

Page 6

OPEROPER

OPER

OPEROPER

IONSIONS

IONS TT

ING INSTRUCING INSTRUC

ING INSTRUC

ING INSTRUCING INSTRUC

IONSIONS

IONS

IONSIONS

2523

11 16 17

ING INSTRUCING INSTRUC

ING INSTRUC TT

T AA

OPEROPER

OPER

(BEHIND PANEL)

1 ON/OFF POWER BUTTON

Press this button to turn the unit on or off. If the unit is off and the ignition switch is on, the unit will turn on automatically when a disc is inserted, or when the MODE switch or BAND switch is pressed.

2 VOLUME / LEVEL CONTROL

To increase the volume level, press the VOL + button. The volume will increase and the level will be shown on the display panel from a minimum of VOL 00 to a maximum of VOL 100. To increase the volume quickly, keep the button pressed. To decrease the volume level, press the VOL - button. Keep the button pressed to decrease the volume quickly. The display will automatically return to the normal indication 5 seconds after the last volume adjustment or when another function is activated. These buttons are also used in conjunction with the Audio Select (SEL) button the bass, treble, balance, and fader levels as described in

3 AUDIO SELECT (SEL) BUTTON

This button is used to select the audio function (volume, treble, bass, balance, or fade) to be adjusted using the Volume/Level Controls

BAND/LOUD

MODE

28,29

4, 5, 6 and 7.

LOC

MONO

MUTE

PAU SCN RPT SHF

AS/PS

3 to adjust

2. Pressing the SELbutton will select bass

T/F

321456

(BAS on the display), treble (TRB), balance (BAL), fader (FAD) or volume (VOL). The display will automatically return to the normal indication 5 seconds after the last adjustment or when another function is activated.

4 BASS CONTROL

To adjust the bass level, first select the Bass

mode by pressing the SEL button 3 so that

the BAS indication appears on the display panel. Within 5 seconds of choosing the Bass mode, press the VOL + or VOL - button adjust the bass response as desired. The bass level will be shown on the display panel from a minimum of BAS--10 to a maximum of BAS 10 (BAS 00 represents flat response). The display will automatically return to the normal indication 5 seconds after the last adjustment or when another function is activated. Adjusting the bass level will automatically return the equalizer setting to the FLAT mode from its previous setting.

5 TREBLE CONTROL

To adjust the treble level, first select the Treble mode by pressing the SEL button the TRB indication appears on the display panel. Within 5 seconds of choosing the Treble

mode, press the VOL + or VOL - button 2 to

VOL

SEL

VOL

POWER

3 4 5 6 7

2 to

3 so that

128-6691

6 of 16

Page 7

adjust the treble response as desired. The treble level will be shown on the display panel from a minimum of TRB--10 to a maximum of TRB 10 (TRB 00 represents flat response). The display will automatically return to the normal indi cation 5 seconds after the last adjustment or when another function is activated. Adjusting the treble level will automatically return the equalizer setting to the FLAT mode from its previous setting.

6 LEFT/RIGHT BALANCE CONTROL

To adjust the left-right speaker balance, first select the Balance mode by pressing the SEL

button 3 so that the BAL indication appears

on the display panel. Within 5 seconds of choosing the Balance mode, press the VOL + or VOL - button ance as desired. The balance position will be shown on the display panel from BAL 10L (full left) through BAL 10R (full right). When the volume level between the left and right speakers is equal, BAL L=R will be shown on the display panel. The display will automatically return to the normal indication 5 seconds after the last adjustment or when another function is activated.

7 FRONT/REAR FADER CONTROL

To adjust the front-rear speaker balance, first select the Fader mode by pressing the SEL

button 3 so that the FAD indication appears

on the display panel. Within 5 seconds of choosing the Fader mode, press the VOL + or VOL - button balance as desired. The fader position will be shown on the display panel from FAD 10R (full rear) through FAD 10F (full front). When the level between the front and rear speakers is equal, FAD F=R will be shown on the display panel. The display will automatically return to the normal indication 5 seconds after the last ad j ustment or when another function is activated.

2 to adjust the front-rear speaker

2 to adjust the bal-

LOCAL (LOC) OPERATION

This feature is used to select the strength of the signals at which the radio will stop during Automatic Seek Tuning. Pressing the button will select the Local setting (LOCAL will appear on the display panel for 5 seconds and LOC will remain in the center of the display) and only strong (local) stations will be received. Pressing and holding the button again will select the Distant setting (Dx will appear on the display panel for 5 seconds) and the radio will stop at a wider range of signals, including weaker (more distant) stations.

9 AUDIO MUTE (MUTE)

This button is used to mute the volume from the system. By pressing the button, a flashing MUTE indication will appear on the display panel and the volume will be muted. Pressing the Mute button again, or activating any other function of the unit will return the volume level to the setting in use before the Mute function was activated.

blbl

bl BAND/LOUDNESS CONTOUR SELECTION

blbl

(BAND/LOUD)

During radio operation, each momentary press of this button will change the radio band. The indication AM, F1, F2, or F3 will appear on the display panel according to your selection. When listening to music at low volume levels, the loud feature will boost the bass and treble ranges to compensate for the characteristics of human hearing. Press the BAND/LOUD button for at least 2 seconds to activate this feature as indicated by a beep tone and LOUD ON appearing on the display panel for about 5 seconds. (LOUD remains on the display.) Pressing the button again for 2 seconds will sound a beep tone and LOUD OFF will appear on the display for about 5 seconds.

OPER

OPEROPER

AA T

TT ING INSTRUC

ING INSTRUCING INSTRUC

TT IONS

IONSIONS

128-6691

7 of 16

Page 8

bmbm

bm MANUAL UP/DOWN TUNING (+ / -)

bmbm

AUTOMATIC SEEK TUNING

IONSIONS

IONS

Each time the + button is pressed, the

radio will tune higher, seeking the next strong station and stop. Similarly, each press of the

- button will tune lower and stop at the next

strong station. To manually seek a specific station, press the button of the appropriate direction until the desired frequency is reached.

Pressing either button for longer than 2.0 seconds will cause MANUAL to appear on the dis-

ING INSTRUCING INSTRUC

ING INSTRUC TT

play. Now when the Up or Down tuning button

is pressed momentarily, tuning will occur two frequency steps at a time. If either button is pressed and held in Manual mode for 2 sec-

OPEROPER

OPER

onds, the manual Seek Tuning function is initiated, whereby the radio will tune rapidly in the appropriate direction and stop on, or close to, the desired frequency when the button is released.

If no further tuning is performed after 5 seconds, AUTO will appear momentarily on the display, and tuning will revert to the original

tuning mode.

bnbn

bn AUTO-STORE TUNING (AS)

bnbn

PRE-SET SCAN TUNING (PS)

During radio operation, press this button momentarily to scan the 6 stations in the pre-set memories of the FM band in use. The unit will stop at each pre-set station for 10 seconds before continuing to the next pre-set station (the frequency on the display panel will flash during Pre-Set Scan operation). Press the button again momentarily to stop Pre-Set Scan operation and remain on the selected frequency in that band.

Pressing the button for longer than 2 seconds will activate the Auto-Store Tuning feature. The radio will automatically scan the band in use and enter strong stations into the pre-set

memory positions for that band. If you have already set the pre-set memories of that band to your favorite stations, activating the AutoStore Tuning feature will erase those stations and enter the new strong stations. This feature is most useful when traveling in a new area where you are not familiar with the local stations.

bobo

STATION PRE-SET MEMORIES

bobo

To set any of the 6 pre-set memory buttons, use the following procedure:

1. Turn the radio on and select the desired band.

2. Select the first station to be pre-set using the Manual Up/Down or Automatic Seek Tuning Controls

3. Press the pre-set button (1-6) to be set

and continue to hold it in. After approximately 2 seconds, the pre-set number will appear on the display panel, indicating that the station is now set into that preset memory position. The station can now be recalled at any time by pressing that button.

4. Repeat the above procedure for the re-

maining pre-sets on that band and for the other 3 bands on the unit.

bpbp

bp LIQUID CRYSTAL DISPLAY PANEL

bpbp

FUNCTIONS

The Liquid Crystal Display (LCD) panel displays the frequency, time, and all activated functions, including five bar graphs which provide a visual representation of the audio signal level.

NOTE: It is a characteristic of LCD panels that,

if subjected to cold temperatures for an extended period of time, they may take longer to illuminate than under normal conditions. In addition, the visibility of the numbers on the LCD may slightly decrease. The LCD readout will return to normal when the temperature increases to a normal range.

bm .

128-6691

8 of 16

Page 9

bqbq

bq DISC SLOT

bqbq

With the label surface facing up, gently insert the disc into the slot until the soft-loading mechanism engages and disc play begins. S--CDP will appear momentarily; the cation will become animated, and CDP appears together with the track number and elapsed time.

CAUTION: This unit is designed for play

brbr

br TRACK SELECT

brbr

These buttons are used to quickly select the beginning of a particular track. With each momentary press of the Forward Track Select button

), the next higher track number will be

(+ selected as shown on the display panel. Similarly, with each momentary press of the Backward Track Select button ( - ), the next lower track number will be selected.

bsbs

bs CUE/REVIEW FUNCTIONS

bsbs

High-speed audible search to any section of the disc can be made by the Cue and Review functions. Press and hold the Cue button (+ tion or the Review button ( idly in the backward direction. During either function, the elapsed time within each track will automatically be shown on the display panel.

btbt

bt DISC PAUSE (PAU) SELECT

btbt

The Pause function is used to freeze disc play when the CD player is in use.S--PAUSE will appear on the display. Press this button again to resume disc play; the S--PAUSE indication will disappear.

of standard 5" (12cm) Compact

ONLY. Do not attempt to use

Discs 3" (8cm) CD-Singles in this unit, either with or without an adaptor, as damage to the player and/or disc can occur. Such damage will not be covered by the Warranty on this product.

) to advance rapidly in the forward direc-

-) to advance rap-

indi-

bubu

REPEAT PLAY SELECTOR (RPT)

bubu

During disc play, press this button to repeat the play of the selected track (S--RPT will appear on the display panel). Play of the track will continue to repeat until the button is pressed again and the S--RPT indication disappears from the display panel. Repeat Play mode will also be cancelled by activating the Shuffle Play

clcl

cl SHUFFLE PLAY SELECTOR (SHF)

clcl

During disc play, press this button to play the tracks on the disc in a random shuffled order (S--SHF) will appear on the display panel). In Shuffle Play mode, pressing the Forward Track Select (+ lect ( order instead of the normal progression. Additional presses will select tracks in random order. The Shuffle Play mode can be cancelled by pressing the button again (S--SHF) indication will disappear from the display panel) or by activating the Repeat Play

Track Scan cm functions.

cmcm

cm TRACK SCAN (SCN)

cmcm

During disc play, press this button to play the first 10 seconds of each track on the disc (S--SCN will appear on the display panel with the track number). When a desired track is reached, press the Scan button again to cancel the function and play of the selected track will continue. Track Scan mode will also be cancelled by activating the Repeat Play

cncn

cn DISC EJECT ( )

cncn

When this button is pressed, disc play is stopped, the disc is ejected and the unit will change to radio operation. If the disc is not removed from the unit within 15 seconds, the disc will be reloaded (CDP will reappear).

cl or Track Scan cm functions.

) or Backward Track Se-

-) will also select tracks in a random

bu or

bu or Shuffle Play cl functions.

OPER

OPEROPER

AA T

TT ING INSTRUC

ING INSTRUCING INSTRUC

TT IONS

IONSIONS

128-6691

9 of 16

Page 10

coco

co TIME/FREQUENCY SELECTOR (T/F)

coco

This unit can display the clock time, radio fre-

IONSIONS

IONS

quency or CD player functions on the display

panel. Pressing the Time/Frequency Selector button when the radio frequency or CD player track indication is shown, will change the display to show the time. The time display will automatically return to the radio frequency or CD player function indication after 5 seconds.

ING INSTRUCING INSTRUC

ING INSTRUC TT

cpcp

cp FM MONO/STEREO SELECTOR (MONO)

cpcp

During FM radio operation, this button is used to select mono or stereo reception of the broadcast signal. Under normal reception conditions,

OPEROPER

OPER

the unit should be left in the stereo mode, as indicated by tening to an FM stereo signal. If the stereo signal is too weak for comfortable listening, press the button to switch to mono reception (the indication will disappear and MONO appears on the display panel). To return to the stereo reception mode, press the button again so that

ST indication returns.

the

cqcq

cq EQUALIZER SELECTOR (EQ)

cqcq

The EQ button applies preset sound effects to the unit’s audio output signal. The EQ button, when pressed, will activate one of the following operating modes: CLASSICS, POP M, ROCK M, DSP OFF, or FLAT. When the EQ function is active, as displayed ( on the panel, the bass and treble levels can still be changed to accommodate the listener’s ear. However, when the levels are changed, the equalizer function is disabled. When the EQ function is not active, the unit returns to the userset bass and treble levels. The FLAT selection indicates no equalizer enhancement of the program, thereby removing the preset sound effects, unless otherwise desired. DSP OFF disables display of the equalizer setting.

crcr

cr MODE SELECTOR (MODE)

crcr

This button is used to select the radio, or the

1010

playback mode for the CD player. Each press

ST on the display panel when lis-

----CLAS, POP, ROCK)

of the button will select a different mode as indicated on the display panel. During CD player operation, this button may be used to change to radio without ejecting the disc (the the display panel to show that a disc is still loaded in the unit). Press the button again to return to CD player mode.

cscs

cs FRONT PANEL RELEASE BUTTON

cscs

This button is used to release the mechanism that holds the front panel to the chassis. To detach the front panel, press the button so that the left side of the panel is released. Grasp the released side and pull it off of the chassis. To re-attach the panel, position the right side of the panel in place first and then press in the left side of the panel until the mechanism locks it into place.

ctct

ct THEFT-DETERRENT LED

ctct

The theft-deterrent Light Emitting Diode (LED) is located behind the front panel and is accessible when the front panel is removed. The flashing light serves as a visual warning to the would-be thief that the unit has been disabled by removal of the front panel.

cucu

cu RESET BUTTON

cucu

A RESET button is located on the front of the chassis (front panel must be removed to access the button). The RESET circuitry is provided to protect the microprocessor circuitry and should only be activated under the following circumstances as it will erase the time and pre-set memories:

1. Upon initial installation after all wiring is completed.

2. If there is a malfunction of any of the switches on the unit, pressing the RESET button may clear the system and return to normal operation.

CDP indication will remain on

128-6691

10 of 16

Page 11

NOTES ON USE OF FRONT PANEL

1. Make sure the front panel is right-sideup when attaching it to the chass is as it cannot be attached when up-side down.

2. Do not press very hard on the front panel when attaching it to the chassis. No more than light to moderate pressure should be needed.

3. When attaching the front panel, make sure the right side is correctly engaged before pressing the left side to lock it into position.

4. When taking the front panel with you, please use the supplied carrying case to protect the panel from dirt and damage. Make sure there is no dust or dirt on the electrical terminals on the back of the panel as this could cause intermittent operation or other malfunctions.

DETACHING THE FRONT PANEL

Release Button

ATTACHING THE FRONT PANEL

Engage right side first

NONO

NONO TES ON FR

TES ON FRTES ON FR

ONT P

ONT PONT P

AA NEL / REMO

NEL / REMONEL / REMO

TE INPUT JACK / SET

TE INPUT JACK / SETTE INPUT JACK / SET

SETSET

ING THE CLOCKING THE CLOCK

SET

ING THE CLOCK

SETSET

ING THE CLOCKING THE CLOCK

1. Turn the vehicle ignition and radio on (radio frequency or disc track number will be shown on the display panel).

2. Momentarily press the Time/Frequency (T/F) button press and hold the T/F button until the time display flashes.

3. While the display is flashing, press the Up Tuning button (+ ) to adjust the hours and the A or P indication, and the Down Tuning button ( correct time.

4. When the correct time is shown on the display panel, press and release the T/F button (or wait 5 seconds) for the display to return to the normal indication.

co to display the time of day. Then

-) to adjust the minutes to the

128-6691

11 of 16

TT ING THE CLOCK

ING THE CLOCKING THE CLOCK

1111

Page 12

SPECIFICATIONSSPECIFICATIONS

SPECIFICATIONS

SPECIFICATIONSSPECIFICATIONS

IONSIONS

IONS TT

Size: 7" W x 2" H x 6-5/16" D

Operating Voltage: 12 volts DC, negative ground

178 mm x 50 mm x 163 mm

SPECIFICASPECIFICA

SPECIFICA

Output Power: 160 watts maximum

Output Wiring: Floating-ground type designed for 4 speaker use.

Output Impedance: Compatible with 4 ohm speakers.

Low-Level Output: 0.8 volt (800 mv, 600mV Limit)

Tuning Range: AM: 530 - 1,710 kHz. (10 kHz. step)

Sensitivity: 4.0 uV

FM Stereo Separation: 25 dB

CD Frequency Response: 20 - 20,000 Hz. +0 / -3 dB

CD Signal/Noise Ratio: 55 dB

CD Channel Separation: 1kHz Limit: 50 dB, 10kHz Limit: 40 dB

CD Distortion: 0.2%

(40 watts x 4 channels)

Front and rear channels CANNOT be combined (bridged) for use with 2 speakers. RCA low-level outputs (rear channels).

FM: 87.5 - 107.9 MHz. (200 kHz. step)

*Specifications are subject to change without notice.

CD-R AND CD-RW PLAYBACK CAPABILITY

This model can play most CD-R and CD-RW media that contains audio programs. Playback of both CD-R and CD-RW depends on the conditions of the recording equipment

and the CD-R or CD-RW disc quality. In some cases, a CD-R or CD-RW disc cannot be played on this unit.

1212

128-6691

12 of 16

Page 13

CD PLCD PL

CD PL

CD PLCD PL

YER ERRYER ERR

YER ERR

YER ERRYER ERR

OR CODESOR CODES

OR CODES

OR CODESOR CODES

CD PL

CD PL CD PL

If a problem should develop while operating the CD player, an error code (ER-1, ER-2, ER-3, etc.) may appear on the display panel. This can indicate a number of problems with the unit, including a mechanical error or an error in the microprocessor control of the player. If an error code should appear, try ejecting and re-loading the disc into the player. While the disc is out of the unit, make sure it is clean, undamaged, and loaded correctly (label surface up). You may

also try activating the RESET button cu on the unit, but this will also erase the time and pre-set

memories. If the suggested measures do not solve the problem, contact an approved warranty station near

you for further assistance.

AA YER A

YER AYER A

ND CD CH

ND CD CHND CD CH

AA NGER ERR

NGER ERRNGER ERR

OR CODES

OR CODESOR CODES

1313

128-6691

13 of 16

1313

Page 14

CARE AND MAINTENANCECARE AND MAINTENANCE

CARE AND MAINTENANCE

CARE AND MAINTENANCECARE AND MAINTENANCE

The radio section of your new sound system does not require any maintenance. We

NCENCE

NCE

recommend that you keep this manual for reference on the many features found in this unit as well as how to set the clock.

The compact disc player section also requires no routine maintenance, but proper understanding of its use and handling will help you obtain maximum enjoyment of its

INTENAINTENA

INTENA

capabilities. The following points should be observed:

! When cleaning the interior of the vehicle, do not get water or cleaning fluids on the unit. ! The CD player is a precision instrument and will not operate properly in extreme heat or cold.

ND MAND MA

ND MA

In case of such conditions, wait until the interior temperature of the vehicle reaches a normal temperature before using the player.

RE ARE A

! If the temperature inside the player gets too hot, a protective circuit will automatically stop

RE A

play of the disc. In this case, allow the unit to cool off before operating the player again.

CACA

! Never insert anything other than a 5" (12 cm) compact disc into the player as the mechanism

can be damaged by foreign objects.

! Do not attempt to use 3" (8 cm) CD-Single discs in this unit, either with or without an adaptor,

as damage to the player and/or disc may occur. Such damage will not be covered by the Warranty on this product.

! When not using the disc player, always remove the compact disc. Do not leave an ejected

disc sitting in the disc slot as this can expose it to sunlight and other causes of damage.

! Do not attempt to open the unit chassis. There are no user serviceable parts or adjustments inside. ! When the vehicle warms up during cold weather or under damp conditions, moisture may

condense on the lens of the disc player. Should this occur, the player will not operate properly until the moisture has evaporated.

! The unit is designed with a vibration dampening CD mechanism to minimize interruption of

disc play due to normal vibration in a moving vehicle. When driving on very rough roads, however, occasional sound skips may occur. This will not scratch or damage the disc and normal play will resume when the rough conditions cease.

CACA

CACA RE A

RE ARE A

ND MA

ND MAND MA

INTENA

INTENAINTENA

NCE

NCENCE

HANDLING COMPACT DISCS

Dirt, dust, scratches, and warpage can cause skips in the playback and deterioration of sound quality. Please follow these guidelines to take care of your compact discs:

! Use only compact discs with the mark . ! Fingerprints, dust, and dirt should be carefully wiped off the disc’s playing surface (shiny side)

with a soft cloth. Wipe in a straight motion from the inside to the outside of the disc.

! Never use chemicals such as record sprays, household cleaners or thinner to clean compact

discs. Such chemicals can irreparably damage the disc’s surface.

! Discs should be kept in their storage cases when not in use. ! Do not expose discs to direct sunlight, high temperatures or high humidity for extended periods. ! Do not stick paper, tape, or labels on the disc surfaces nor write on them with any type of marker.

128-6691

14 of 16

1414

Page 15

WW A

12 MONTH LIMI12 MONTH LIMI

12 MONTH LIMI

12 MONTH LIMI12 MONTH LIMI

AUDIOVOX ELECTRONICS CORPORATION (the Company) warrants to the original retail purchaser of this product that should this product or any part thereof, under normal use and conditions, be proven defective in material or workmanship within 12 months from the date of original purchase, such defect(s) will be repaired or replaced with new or reconditioned product (at the Company's option) without charge for parts and repair labor.

To obtain repair or replacement within the terms of this Warranty, the product is to be delivered with proof of warranty coverage (e.g. dated bill of sale), specification of defect(s), transportation prepaid, to the warranty center at the address shown below.

This Warranty does not extend to the elimination of car static or motor noise, to correction of antenna problems, to costs incurred for installation, removal, or reinstallation of the product, or damage to tapes, compact discs, speakers, accessories, or vehicle electrical systems.

This Warranty does not apply to any product or part thereof which, in the opinion of the Company, has suffered or been damaged through alteration, improper installation, mishandling, misuse, neglect, accident, or by removal or defacement of the factory serial number/bar code label(s). THE EXTENT OF THE COMPANY'S LIABILITY UNDER THIS WARRANTY IS LIMITED TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE AND, IN NO EVENT, SHALL THE COMPANY'S LIABILITY EXCEED THE PURCHASE PRICE PAID BY PURCHASER FOR THE PRODUCT.

This Warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, SHALL BE LIMITED TO THE DURATION OF THIS WRITTEN WARRANTY. ANY ACTION FOR BREACH OF ANY WARRANTY HEREUNDER INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY MUST BE BROUGHT WITHIN A PERIOD OF 30 MONTHS FROM DATE OF ORIGINAL PURCHASE. IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY CONSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREACH OF THIS OR ANY OTHER WARRANTY, EXPRESS OR IMPLIED, WHATSOEVER. No person or representative is authorized to assume for the Company any liability other than expressed herein in connection with the sale of this product.

Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damage so the above limitations or exclusions may not apply to you. This Warranty gives you specific legal rights and you may also have other rights which vary from state to state.

U.S.A.: AUDIOVOX ELECTRONICS CORPORATION, 150 MARCUS BLVD., HAUPPAUGE, NEW YORK 11788 • 1-800-645-4994

CANADA: CALL 1-800-645-4994 FOR LOCATION OF WARRANTY STATION SERVING YOUR AREA

TED WTED W

TED W

TED WTED W

RRRR

NTNT

RRRR

NTNT

Form No. 128-4270A

AA RR

RRRR

RRRR A

AA NT

NTNT

NTNT Y

1515

128-6691

15 of 16

Page 16

Printed in China

128-6691

16 of 16