Audiovox ACD-13 User Manual
OO
WNER'S MANUWNER'S MANU
O
WNER'S MANU
OO
WNER'S MANUWNER'S MANU
ALAL
AL
ALAL
TRACK/SKIP
BAND
Released 9-19-02
ACD-13
ACD-17ACD-17
ACD-17
ACD-17ACD-17
T/F
AA
CD-17CD-17
A
CD-17
AA
CD-17CD-17
AM/FM/MPX RADIO
WITH DETACHABLE FRONT PANEL,
COMPACT DISC PLAYER
AND QUARTZ CLOCK
MUTE
N
I
N
G
U
VOL
SEL
VOL
T
128-6496
1 of 16
RELEJECT
THIS PAGE INTENTIONALLY LEFT BLANK
22
2
22
128-6496
2 of 16
INSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONS
This unit is designed for installation in cars, trucks, and vans with an existing radio opening. In many cases,
a special installation kit will be required to mount the radio to the dashboard. These kits are available at
electronics supply stores and car stereo specialist shops. Always check the kit application before purchasing to
make sure the kit works with your vehicle. If you need a kit but cannot find it available, call our toll-free “HELP” line at
1-800-645-4994.
UNIVERSAL INSTALLATION PROCEDURE USING MOUNTING SLEEVE
1. Remove the front panel from the unit by pressing the RELease button at the top right corner; then slide the mounting
sleeve off of the chassis. If it is locked into position, use the removal tools (supplied) to disengage it.
2. Check the dashboard opening size by sliding the mounting sleeve into it. If the opening is not large enough, carefully
cut or file as necessary until the sleeve easily slides into the opening. Do not force the sleeve into the opening
or cause it to bend or bow. Check that there will be sufficient space behind the dashboard for the radio chassis.
3. Locate the series of bend tabs along the top, bottom, and sides of the mounting sleeve. With the sleeve
fully inserted into the dashboard opening, bend as many of the tabs outward as necessary so that the
sleeve is firmly secured to the dashboard.
4. Place the radio in front of the dashboard opening so that the wiring can be brought through the mounting
sleeve. Follow the wiring diagram carefully and make certain all connections of the wiring harness are
secure and insulated with wire nuts or electrical tape to insure proper operation of the unit. After completing
the wiring connections, turn the unit on to confirm operation (ignition switch must be “on”). If unit does not
operate, recheck all wiring until problem is corrected.
5. Carefully slide the radio into the mounting sleeve making sure it is right-side-up until it is fully seated and
the spring clips lock it into place.
6. Attach one end of the perforated support strap (supplied) to the screw stud on the rear of the chassis using
the hex nut provided. Fasten the other end of the perforated strap to a secure part of the dashboard either
above or below the radio using the screw provided. Bend the strap to position it as necessary.
CAUTION:The rear of the radio must be supported with the strap to prevent damage to the dashboard
7. Test radio operation by referring to the Operating Instructions.
INSTALLATION USING KITS
1. If your vehicle requires the use of an installation kit to mount this radio, follow the instructions included with
the installation kit to attach the radio to the mounting plate supplied with the kit.
2. Wire and test the radio as described in Step 4 above.
3. Install the radio/mounting plate assembly to the sub-dashboard according to the instructions of the installation kit.
4. Attach the support strap to the radio and dashboard as described in Step 6 above.
5. Replace the dashboard trim panel.
ISO INSTALLATION PROCEDURE
This unit has threaded holes in the chassis side panels which may be used with the original factory mounting
brackets of some Toyota, Nissan, Mitsubishi, Isuzu, Hyundai and Honda vehicles to mount the radio to the
dashboard. Please consult with your local car stereo specialist shop for assistance on this type of installation.
1. Remove the existing factory radio from its dashboard or center console mounting. Save all hardware and
brackets as they will be used to mount the new radio.
2. Carefully unsnap the plastic frame from the front of the new radio chassis. Remove and discard the frame.
3. Remove the factory mounting brackets and hardware from the existing radio and attach them to the new radio.
CAUTION: DO NOT EXCEED M5 X 6 MM MAXIMUM SCREW SIZE.
4. Wire the new radio to the vehicle as per step 4 above.
5. Mount the new radio assembly to the dashboard or center console using the reverse procedure of step 1.
from the weight of the radio or improper operation due to vibration.
LONGER SCREWS MAY TOUCH AND DAMAGE COMPONENTS INSIDE THE CHASSIS.
INST
INSTINST
INSTINST
ALL
ALLALL
ALLALL
A
AA
AA
T
TT
TT
ION INSTRUC
ION INSTRUCION INSTRUC
ION INSTRUCION INSTRUC
T
TT
TT
IONS
IONSIONS
IONSIONS
33
3
33
128-6496
3 of 16
TT
OLL-FREE INSTOLL-FREE INST
T
OLL-FREE INST
TT
OLL-FREE INSTOLL-FREE INST
The installation and wiring connections for this unit are so simple, we doubt you'll need our help, but, if you
do, we're here to help you. Just call our toll-free telephone assistance line at 1-800-645-4994 during the days
IONSIONS
IONSIONS
IONS
and hours shown (U.S.A. and Canada only).
TT
TT
T
DAY
MON. - FRI.
SATURDAY
NUT (5MM)
ION INSTRUCION INSTRUC
ION INSTRUCION INSTRUC
ION INSTRUC
TT
TT
T
AA
AA
A
SCREW
ALLALL
ALLALL
ALL
(5MM)
INSTINST
INSTINST
INST
FASTEN THIS END TO SECURE
PART OF DASHBOARD.
DRILL HOLE IF NECESSARY.
NOTE: PLASTIC FRAME MUST BE REMOVED (UNSNAP ON LEFT
AND RIGHT SIDES) TO USE REMOVAL TOOLS.
PACIFIC
5:30AM - 4PM
6AM - 2PM
UNIVERSAL INSTALLATION USING MOUNTING SLEEVEUNIVERSAL INSTALLATION USING MOUNTING SLEEVE
UNIVERSAL INSTALLATION USING MOUNTING SLEEVE
UNIVERSAL INSTALLATION USING MOUNTING SLEEVEUNIVERSAL INSTALLATION USING MOUNTING SLEEVE
PERFORATED STRAP
FASTEN THIS END TO SCREW
STUD ON REAR OF CHASSIS
SCREW STUD
MOUNTING SLEEVE
ALLALL
AA
TT
ALL
ALLALL
ION ASSISTION ASSIST
A
T
ION ASSIST
AA
TT
ION ASSISTION ASSIST
AA
A
AA
NCENCE
NCE
NCENCE
TIME ZONE
MOUNTAIN
6:30AM - 5PM
7AM - 3PM
EXISTING DASH OPENING
FILE EDGES TO FIT IF NECESSARY - DO NOT OVERFILE
NOTE: IF DASH IS SOLID, USE REAR SIDE (WITHOUT THE LIP) OF
MOUNTING SLEEVE AS A TEMPLATE & CUT OPENING
RADIO
REMOVAL TOOLS
CENTRAL EASTERN
7:30AM - 6PM
8AM - 4PM
8:30AM - 7PM
9AM - 5PM
BEND TOP
TABS UPWARD
BEND BOTTOM
TABS DOWNWARD
33
3
33
FOR PROPER OPERATION OF THE CD PLAYER, THE CHASSIS MUST BE
MOUNTED WITHIN 20° OF HORIZONTAL. MAKE SURE THE UNIT IS
MOUNTED WITHIN THIS LIMITATION.
REMOVE THE PLASTIC FRAME FROM THE FRONT OF THE CHASSIS BY CAREFULLY UNSNAPPING IT.
44
4
44
CAUTION:
UNSNAP ON LEFT AND
RIGHT SIDES
PLASTIC FRAME
ISO INSTALLATIONISO INSTALLATION
ISO INSTALLATION
ISO INSTALLATIONISO INSTALLATION
MAXIMUM
SCREW SIZE
M5 x 6
FACTORY MOUNTING
BRACKETS
SIDE VIEW
OF
CHASSIS
20° MAX.
FRONT PANEL
TYPICAL INSTALLATION
MAXIMUM
SCREW SIZE
M5 x 6
128-6496
4 of 16
RR
AA
DIO WIRINGDIO WIRING
R
A
DIO WIRING
RR
AA
DIO WIRINGDIO WIRING
REFER TO PAGE 6 FOR SPEAKER WIRING
CONTAINS:
1- 15A FUSE
1- 0.5A FUSE
RADIO WIRING
6
55
5
55
128-6496
5 of 16
Loading...