Audiovox ACC56M Owner's Manual And Installation Manual

OWNER’S MANUAL

AND

INSTALLATION GUIDE

10-DISC CD CHANGER

MADE IN CHINA

Visit us at www.asaelectronics.com to see our full line of mobile audio and video products.

ACC56M

1

I N T R O D U C T I O N

F E A T U R E S

Congratulations on your purchase of the AQUATRONICS ACC56M REMOTE-CONTROL
10-DISC CD CHANGER.

This system allows you to easily upgrade your existing audio system to include a quality CD
entertainment function. Best of all, the CD Changer is easy to install. There is only one cable to
plug in to the rear of the already equipped radio. Just follow the simple step-by-step instructions
that follow.

■ Remote mount changer holds up to 10 compact discs.

■ Advanced technology includes 8x oversampling digital filter and twin1-bit digital/analog

converters

■ The special design allows horizontal, vertical or 45-degree mounting.

■ Designed to work with Aquatronics and Voyager CDC ready radios.

I N D E X

Introduction and Contents
Packing List
Before Installing the Unit Page
Where to Install the Changer
Installation
Overall Wiring View

Hints for Correct and Safe Operation
Handling the Discs
Use of the CD Magazine
Specifications
Troubleshooting

page 1
page 2
page 3
page 4
page 5
page 9

page 10
page 11
page 12
page 14
page 15

32

PACKING LIST

Main Unit

Installation Parts

Other Accessories

The mechanism in the CD changer is "locked" into place during
shipment by three transport lock screws. Be sure to remove the
screws prior to installation.

CAUTION:

After removing the transport lock screws, place the
supplied seals (A) over the screw holes. These
seals are used to keep dust out of the unit, which
could cause a malfunction.

1. To prevent a short-circuit,

●

Be sure to turn off the ignition and remove the negative (-) battery cable, prior to installation.

●

Connect power wires last.

NOTE: If the changer is to be installed in a vehicle that is equipped with an on-board drive or

navigation computer, do not disconnect the battery cable. If the cable is disconnected,
5 the computer memory may be lost. Under these conditions, use extra caution during
installation not to cause a short circuit.

2. Do not install the unit in the following locations.

●

Locations exposed to direct sunlight.

●

Where hot air is discharged from the car heater.

●

In areas subject to extreme temperatures.

3. Incorrect installation can cause the disc to skip when playing.
Be sure to mount the unit firmly in place, using the supplied brackets and screws.

4 .●Be sure to use the supplied screws.

●

Be careful not to snag any wires when tightening screws.

●

Be careful not to damage the vehicle wiring.

5. ●This unit cannot be installed on its side, end, or upside down.

Installation in such positions will cause malfunctioning of the mechanism.

BEFORE INSTALLING THE UNIT

lnstallation and Wiring Precautions

Transport Lock Screws

1pc.

1pc. 4pcs.

2pcs.

1pc.

4pcs. 1pc.

1pc.

1pc.

1pc.

1pc.

Bracket(L) Bracket(R) Hexagonal bolt

with washer (M5 x 10)

Screw (C) phillips

Head Self-Tapping Screw

(T3 x12)

5Meter Din Cable

CD Magazine(P/N 10CD56M)

lndex label sheet

Owner’s Manual

and lnstallation Guide

Self-tapping screw

(T5 x12)

Seals(A) Seals(B)

B O T T O M

F R O N T

R E A R

TRANSPORT LOCK SCREWS

(2 RIGHT SIDE,1 LEFT SIDE)

OWNER’S MANUAL

AND

INSTALLATION GUIDE

10-DISC CD CHANGER

ACC56M