Audiovox 1286016A User Manual

EZCRG
Owner ’s Manual
A. Introduction
The EZCRG is a self-contained entertainment center in your vehicle which makes your road trips enjoyable. This versatile floor console incorporates a high brightness 5” color TV and vertical eject Video Cassette Player , complete with a built-in speaker, a built-in foil antenna, headphone jacks, AV input jacks, A V output jacks and a universal remote control. Installed between the driver and passenger front seats, with a floor mounting plate available for most cars, vans and trucks. This aesthetic console is constructed of two-tone, gray textured plastic with an extra cup holder, jack cover , protective bar and cigarette lighter jack to compliment your vehicle’s decor . The EZCRG standard manufacture ensures reliability and longevity . Please read the following instructions thoroughly for correct installation and proper operation. Store this manual in a convenient and safe place for future reference.
B. Precaution
1. Use only good quality VHS tapes and discard worn out tapes to prevent video head clogging. If the heads get dirty over a period of time during normal operation of the VCP , and the automatic tracking control will not remove the snow from the picture we recommend using a cleaning cartridges sparingly to restore normal picture.
2 . In order to maintain a safe mounting arrangement, this console must be
secured to the floor of the vehicle according to Installation Guide contained in this manual. Failure to do so may result in the console becoming a projectile in the event of an accident.
3. Before working under the vehicle, block the wheels to prevent accidental injury.
4. Before drilling any holes in the vehicle, verify that the drill bit will not enter into the frame rail(s) of the vehicle of damage electrical wires, fuel lines, brake lines, hoses, exhaust system components or any other items that will impair that operation of the vehicle. The console must be secured to the floor panel of the vehicle. Check under the vehicle to ensure that the holes will be in the proper locations. Also check under the carpet to ensure that there are no wiring harnesses, fuel lines, etc. that could be damaged when drilling through the floor pan of the vehicle.
CAUTION: Children should not be allowed to wear headphones unless
carefully supervised. The headphone wires may become entangled and induce choking.
5. Do not use gasoline, thinners or other thinning liquids to clean the unit.
Remove dust and stains with a damp cloth.
6. Do not cover the unit with a cloth during operation; the internal temperature will rise and may damage the unit.
2
7. In case anything falls into the cabinet, unplug the unit and have it checked by
qualified personnel prior to further operation.
8. Only use the supplied power cord, and not use other power supplies even if
they have the same current characteristics.
9. Always unplug the unit from the cigarette lighter socket of the vehicle if you do
not intend to use it for an extended period of time. In addition, first disconnect
the cord from the cigarette lighter socket before disconnecting the cable from the 4-PIN socket on the back of the unit; never disconnect the cable from the unit connector by pulling the cord.
10. Always remove the VHS tape from the unit after use.
1 1. To avoid electrical hazards, do not disassemble the cabinet.
12.Due to the nature of TV signals, vehicle motion, direction the vehicle is facing, distance from nearby transmitter , nearby surroundings and weather may adversely af fect TV reception. These conditions may result in picture roll, poor reception (snowy picture) and momentary loss of color (especially when the vehicle is in motion).
C. Legend for Figure 1
1. Picture Button
2. Auto Program Button
3. TV/AV Button
4. Volume Up and Down Buttons
5. Channel Up and Down Buttons
6. Infrared Remote Control Sensor
7. Power Button
8. Auto Repeat Button
9. Rewind Button
10. Stop/Eject Button
1 1. (Fast) Forward Button
12. Play Button
13. Headphone Jack #1
14. Video Input Jack
15. Audio Left Input Jack
16. Audio Right Input Jack
17. Headphone Jack #2
18. Speaker Holes
19. Tape Door
20. Protective Bar
21. Cigarette Lighter Jack
22. Jack Cover
3
Figure 1
NOTE: Whenever unit loading exceeds 3 Amperes, the unit power supply
will overload and automatically disconnect the power supply from +12V DC vehicle power at the cigarette lighter jack.
D. Contents in Kit
TV and VCP Floor Console Owner’s Manual Remote Control 12V Cigarette Lighter Cord and Plug (for powering this unit) Cardboard Mounting T emplate (for positioning the mounting holes on the floor) Hardware Package for Securing Console to Vehicle Contains the following: 6 Floor Bolts 6 Sealing Washers 6 Fender Washers 6 Floor Nuts 2 Console Bolts 2 Spring Washers 1 Mounting Plate
E. T ools Required (not supplied)
Electric Drill 1/8” Steel Drill Bit 1/4” Steel Drill Bit Socket Wrench Set with Deep-Wall, 7/16” Socket Box Wrench, Size 7/16” Standard Utility Knife (or Equivalent)
NOTE: Two people are required for inst allation.
F. Installation Guide (Refer to Figure 2)
1. Temporarily place the cardboard mounting template on an appropriate
mounting location on the floor between driver/passenger seats, with the rounded end of the template facing the front of your vehicle. Make sure that you have checked both underneath the vehicle and within the vehicle (under the carpet) for obstructions.
2. Drill 6 small 1/8” pilot holes though the marks on the template to verify
that the holes are in the proper locations.
3. After verifying that the 1/8” pilot holes are in the proper locations, use
the 1/4” drill bit to enlarge the pilot holes.
4. Remove the template and replace it with the mounting plate on the floor
over the drilled holes.
5. Place the 6 floor bolts through the mounting plate and into the holes just
drilled.
4
Loading...
+ 8 hidden pages