Audiovox 1285882C User Manual
Model APS-800
Owner’s Manual
4 Button Remote Security System
IMPORTANT !
system is equipped with selectable manual override circuitry. It is possible that you will need
to override you security system if the transmitter becomes lost, or inoperative due to battery
failure. Reading the sections on "Manually Overriding Your System" is necessary to fully
understand the procedure required to enable your vehicle in such situations. In addition, the
chart on the last page of this manual has a section for the particular features and options
installed in your vehicle as well as the override method selected. Although the default mode
is "Valet Switch" operation, the system can be configured for "Custom Code" operation for
enhanced security. Confirm the override mode selected on the last page of this manual, and
familiarize yourself with the section on it's operation.
FEATURES :
w 2 Four Button S.A.W. Anti-Code Grabbing Transmitters
w Six Channel Code Learning Programmable Receiver
w External Superheterodyne Receiver Antenna
w Single Or Two User Programmable W/Separate Control Outputs
w Single Button Lock/Unlock or Separate Button Lock/Unlock or Both
w Single Step Unlock Or Two Step Unlock
w New Enhanced Panic Feature
w Smart Disarm (If triggered, elect to shut off siren, or disarm entire unit )
w Adjustable Shock Sensor Via The Transmitter
w Safe Start Output Controlled From Channel 3 (Option Channel 3 For Trunk, Or For R/S)
w Remote Panic In All Modes
w Improved Custom Code Override, User Selectable and Programmable
w Protected Push Button Valet/Override Switch
w 7 Function LED
w Intrusion Alert With Memory
w Instant Siren Activation
w Starter Disable Output
w Additional Engine Immobilizer Output, (Optional Relay Required)
w True Last Door Arming (Hardwire Only)
w Defective Zone By-Pass
w Defective Zone Chirp Confirmation (Unit Chirps To Report Zone Cleared)
w 6 Tone Mini Siren
w Car Horn Output For Additional Alarm Response
w Additional Negative Trigger Input (Hood & Trunk)
w RF Inhibit With Ignition On
w Parking Light Flasher (Relay On Board)
w Plug In Dual Stage Shock Sensor (Pre-detect, Full Trigger, and “City Mode”)
w Audible Arm, Disarm, Defect, And Tamper Chirp Indications
w Headlight Control Output
w Illuminated Entry Control Output
OPTIONS :
w Remote Trunk Release (must have electronic trunk release)
w Remote Keyless Entry (must have power door locks)
w Multiple Vehicle Capable
w Remote Starter
w Remote Power Window Roll Up
w Remote Garage Door Interface
In order to provide you with the highest level of security to your vehicle, this
with Dual Stage Shock Sensor
(Any button other than unlock stops siren, no change to the units state)
(Pre-Detect Off, Pre & Full Detect Off, City Mode)
(Press & Hold Lock/Unlock Button For 3 Seconds To Engage)
(Improved Timing To Minimize RF Interference.)
YOUR “ANTI CODE GRABBING“ TRANSMITTERS
The transmitters included with your new security system use the most advanced and
secure form of radio frequency transmission available on any current automotive security
system. Some of today’s sophisticated auto thieves use a device known as a code grabber,
which will receive and store the signal from your keychain transmitter, and re transmit at a
later time to disarm your system.
Your Keeloq Code Hopping transmitters will change their signal every time the button is
pressed, so when a thief grabs then re-transmits your signal, the alarm system
respond.
If your transmitter button is pressed more than fifty times while it is out of range of the
vehicle (children playing with your keys), the transmitter will not operate when you return
to the vehicle, and will need to be re aligned to the receiver. To do this, simply press button
1 two times within a one second time period. The system will now respond to that transmitter each time a button is pressed.
NOTE: This system is custom configurable and can be set up to operate with a number of
options controlled from any transmitter button or button combination. For reference, we will
describe operation assuming that your system is programmed for sperate lock and unlock
buttons. Also, reference will be made to the icons as shown on the buttons below.
Consult your installation center if your system has been configured differently.
NOTE: Your system has the option of using a siren, the vehicle horn, or both for the
sounding device. Where the siren is referenced below, the horn or both may in fact chirp,
or beep.
ARMING THE SYSTEM - ACTIVE
1. Turn off the engine, exit the vehicle, and close all doors, hood lid, and trunk lid.
2. Press and release button Lock/Arm button on the keychain transmitter.
þ The dash mounted LED begins to flash slowly.
þ Parking Lights flash one time.
þ Siren sounds one chirp.
If the siren sounds 3 chirps, then you have left a door, trunk, or hood lid
ajar. Simply close the opened entry point to provide full protection. If the
siren did not sound when arming, then the chirps have been turned off,
and you should refer to the section titled “ELIMINATING THE ARM /
DISARM CHIRPS“ in this manual.
o Doors Lock - Optional
NOTE: If the optional headlamp illumination feature has been added, and has been selected
for operation when arming, as an added convenience, the system will turn on the
headlights when the system is armed.
SILENT ARMING - ACTIVE (Must be activated during programming)
1. Turn off the engine, exit the vehicle, and close all doors, hood lid, and trunk lid.
2. Press and hold button the Lock/Arm button on the keychain transmitter for 2 seconds.
þ The dash mounted LED begins to flash slowly.
þ Parking Lights flash one time.
þ Siren will not sound.
If the siren sounds 3 chirps, then you have left a door, trunk, or hood lid
ajar. Simply close the opened entry point to provide full protection
o Doors Lock - Optional
will not
Page 2
NOTE: If the optional Headlamp illumination feature has been added, and has been selected
for operation when arming, as an added convenience, the system will turn on the
headlights when the system is armed.
ARMING THE SYSTEM - PASSIVE ( AUTOMATIC )
1. Turn off the engine, exit the vehicle, and close and lock all doors, hood lid, and trunk lid.
þ The dash mounted LED begins to flash rapidly, indicating 30 second passive
arming has begun.
2. Opening any protected entry point during the 30 second passive arming cycle will immedi-
ately suspend automatic arming, and the 30 second passive arming cycle will re start when
all doors are closed. At the end of the passive arming cycle:
þ The dash mounted LED begins to flash slowly.
þ Parking Lights flash one time.
þ Siren sounds one chirp
If the siren did not sound when arming, then the chirps have been turned
off, and you should refer to the section titled “ELIMINATING THE ARM /
DISARM CHIRPS“ in this manual.
o Doors Lock - Optional
Door locking during passive arming is a selectable feature.The alarm can
be programmed to allow the doors to lock only when arming using the
keychain transmitter, and they will not automatically lock during passive
arming.
PROTECTION WHILE THE SYSTEM IS ARMED
þ Opening any protected door, hood, or trunk lid will cause the alarm to immediately
sound.The alarm will continue to sound for 30 seconds, then stop and continue to
monitor all protected entry points. If the thief left a door opened, the alarm will sound
for six 30 second cycles, remain armed and ignore that triggered zone.
þ Whenever the system is armed, the red dash mounted LED indicator will slowly flash.
This serves as a visual deterrent to the potential thief. The LED is a very low current
bulb, and will not cause the vehicle’s battery to drain, even when left unattended for
extended periods.
þ Whenever the system is triggered, the vehicle’s parking lights will flash for the full 30
second alarm cycle, attracting visual attention to the vehicle.
þ Optional - Whenever the system is armed, the vehicle’s starting circuit will be by-
passed. If the thief should choose to ignore the siren, the vehicle can not be started.
þ Any mild impact to the vehicle’s glass will cause the alarm to sound a short series of
warning tones.
þ Any strong impact to the vehicle’s glass will cause the alarm to trigger for the full 30
second alarm cycle.
NOTE: If the optional interior illumination circuit was installed, the interior light will flash as
well for the full 30 second alarm cycle.
DISARMING THE SYSTEM
NOTE:If the optional 2 step door unlock circuit is installed, when the unlock transmitter button
is activated, the drivers door only will unlock, pressing the unlock button a second time
will cause all doors to unlock.
NOTE: If your transmitter has been configured with single button Lock/Unlock as shown, to
activate the all door unlock feature operate the Lock/Unlock button a second time
within 3 seconds of the first unlock command.
Page 3
1. As you approach the vehicle, press and release the Unlock/Disarm button on the
keychain transmitter.
þ The dash mounted LED turns off.
The LED will start flashing rapidly, indicating that the system is re-arming
automatically. Open any door to suspend the automatic arming.
þ Parking Lights flash two times.
If the parking lights flashed three times, then the alarm was triggered in
your absence. Before turning the key on, examine the LED to identify
which zone was triggered.
þ Siren sounds two chirps.
If the siren sounds 4 chirps, then the alarm was triggered in your
absence. Before turning the key on, examine the LED and refer to the
INTRUSION WARNING SIGNALS section of this manual to identify
which zone was triggered.
If the siren did not sound when disarming, then the chirps have been
turned off, and you should refer to the section titled “ ELIMINATING
THE ARM / DISARM CHIRPS “ in this manual.
o Doors Unlock - Optional
o 2 Step Doors Unlock - Optional
NOTE: If the optional Headlamp illumination feature has been added, and has been selected
for operation when disarming, as an added convenience, the system will turn on the
headlights when the system is disarmed.
SILENT DISARMING (Must be activated during programming)
NOTE: If the optional 2 step door unlock circuit is installed, when the unlock transmitter
button is activated, the drivers door only will unlock, pressing the unlock button a
second time will cause all doors to unlock.
NOTE: If your transmitter has been configured with single button Lock/Unlock as shown, to
activate the all door unlock feature operate the Lock/Unlock button a second time
within 3 seconds of the first unlock command.
1. Press and hold button the Unlock/Disarm button on the keychain transmitter for 2 seconds.
þ The dash mounted LED turns off.
The LED will start flashing rapidly, indicating that the system is re-arming
automatically. Open any door to suspend the automatic arming.
þ Parking Lights flash two times.
If the parking lights flashed three times, then the alarm was triggered in
your absence. Before turning the key on, examine the LED to identify
which zone was triggered.
þ Siren will not sound.
If the siren sounds 4 chirps, then the alarm was triggered in your
absence. Before turning the key on, examine the LED and refer to the
INTRUSION WARNING SIGNALS section of this manual to identify
which zone was triggered.
o Doors Unlock - Optional
o 2 Step Doors Unlock - Optional
Page 4
Loading...