Audiovox 1285867, ACD-21 User Manual
OWNER'S MANUAL
ACD-21
AM/FM/MPX RADIO
WITH DETACHABLE FRONT PANEL,
COMP ACT DISC PLAYER
AND QUARTZ CLOCK
INSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONS
This unit is designed for installation in cars, trucks, and vans with an existing radio opening. In many cases, a
special installation kit will be required to mount the radio to the dashboard. These kits are available at electronics
supply stores and car stereo specialist shops. Always check the kit application before purchasing to make sure the kit
works with your vehicle. If you need a kit but cannot find it available, call our toll-free “HELP” line (1-800-645-4994).
UNIVERSAL INSTALLATION PROCEDURE USING MOUNTING SLEEVE
1. Remove the detachable front panel, if it is attached to the chassis, by pushing the RELEASE button. Slide the
mounting sleeve off of the chassis. If it is locked into position, use the removal tools (supplied) to disengage it.
2. Check the dashboard opening size by sliding the mounting sleeve into it. If the opening is not large enough, carefully
cut or file as necessary until the sleeve easily slides into the opening. Do not force the sleeve into the opening
or cause it to bend or bow. Check that there will be sufficient space behind the dashboard for the radio chassis.
3. Locate the series of bend tabs along the top, bottom, and sides of the mounting sleeve. With the sleeve
fully inserted into the dashboard opening, bend as many of the tabs outward as necessary so that the
sleeve is firmly secured to the dashboard.
4. Place the radio in front of the dashboard opening so that the wiring can be brought through the mounting
sleeve. Follow the wiring diagram carefully and make certain all connections of the wiring harness are
INSTALLATION INSTRUCTIONS
secure and insulated with wire nuts or electrical tape to insure proper operation of the unit. After completing
the wiring connections, attach the front panel and turn the unit on to confirm operation (ignition switch must
be “on”). If unit does not operate, re-check all wiring until problem is corrected. Once proper operation is
achieved, turn off the ignition switch and proceed with final mounting of the chassis.
5. Carefully slide the radio into the mounting sleeve making sure it is right-side-up until it is fully seated and
the spring clips lock it into place.
6. Attach one end of the perforated support strap (supplied) to the screw stud on the rear of the chassis using
the hex nut provided. Fasten the other end of the perforated strap to a secure part of the dashboard either
above or below the radio using the screw and hex nut provided. Bend the strap to position it as necessary.
CAUTION: The rear of the radio must be supported with the strap to prevent damage to the dashboard from
7. Re-attach the front panel to the chassis and test radio operation by referring to the Operating Instructions for
the weight of the radio or improper operation due to vibration.
theunit.
INSTALLATION USING KITS
1. If your vehicle requires the use of an installation kit to mount this radio, follow the instructions included with
the installation kit to attach the radio to the mounting plate supplied with the kit.
2. Wire and test the radio as described in Step 4 above.
3. Install the radio/mounting plate assembly to the sub-dashboard according to the instructions of the installation kit.
4. Attach the support strap to the radio and dashboard as described in Step 6 above.
5. Replace the dashboard trim panel.
ISO INSTALLATION PROCEDURE
This unit has threaded holes in the chassis side panels which may be used with the original factory mounting
brackets of some Toyota, Nissan, Mitsubishi, Isuzu, Hyundai and Honda vehicles to mount the radio to the
dashboard. Please consult with your local car stereo specialist shop for assistance on this type of installation.
1. Remove the existing factory radio from its dashboard or center console mounting. Save all hardware and
brackets as they will be used to mount the new radio.
2. Carefully un-snap the plastic frame from the front of the new radio chassis. Remove and discard the frame.
3. Remove the factory mounting brackets and hardware from the existing radio and attach them to the new radio.
CAUTION: DO NOT EXCEED M5 X 8 MM MAXIMUM SCREW SIZE.
4. Wire the new radio to the vehicle as per step 4 above.
1
5. Mount the new radio assembly to the dashboard or center console using the reverse procedure of step 1.
LONGER SCREWS MAY TOUCH AND DAMAGE COMPONENTS INSIDE THE CHASSIS.
TT
OLL-FREE INSTOLL-FREE INST
T
OLL-FREE INST
TT
OLL-FREE INSTOLL-FREE INST
The installation and wiring connections for this unit are so simple, we doubt you'll need our help, but, if you do,
we're here to help you. Just call our toll-free telephone assistance line at 1-800-645-4994 during the days and
hours shown (U.S.A. and Canada only).
DAY
MON. - FRI.
SATURDAY
NUT (5MM)
SCREW
(5MM)
NUT (5MM)
FASTEN THIS END TO SECURE PART OF DASHBOARD. DRILL HOLE IF NECESSARY.
FOR PROPER OPERATION OF THE CD PLAYER, THE CHASSIS
MUST BE MOUNTED WITHIN 20° OF HORIZONTAL. MAKE
SURE THE UNIT IS MOUNTED WITHIN THIS LIMITATION.
SIDE VIEW
OF
CHASSIS
PACIFIC
5:30AM - 4PM
6AM - 2PM
UNIVERSAL INSTALLATION USING MOUNTING SLEEVEUNIVERSAL INSTALLATION USING MOUNTING SLEEVE
UNIVERSAL INSTALLATION USING MOUNTING SLEEVE
UNIVERSAL INSTALLATION USING MOUNTING SLEEVEUNIVERSAL INSTALLATION USING MOUNTING SLEEVE
PERFORATED STRAP
FASTEN THIS END TO SCREW
STUD ON REAR OF CHASSIS
MOUNTING SLEEVE
CAUTION:
20° MAX.
FRONT PANEL
ALLALL
AA
TT
ALL
ALLALL
MOUNTAIN
6:30AM - 5PM
7AM - 3PM
EXISTING DASH OPENING
FILE EDGES TO FIT IF NECESSARY - DO NOT OVERFILE
NOTE: IF DASH IS SOLID, USE REAR SIDE (WITHOUT THE LIP) OF
MOUNTING SLEEVE AS A TEMPLATE & CUT OPENING
SCREW STUD
ION ASSISTION ASSIST
A
T
ION ASSIST
AA
TT
ION ASSISTION ASSIST
TIME ZONE
7:30AM - 6PM
8AM - 4PM
RADIO
REMOVAL TOOLS
CENTRAL EASTERN
AA
A
AA
NCENCE
NCE
NCENCE
8:30AM - 7PM
9AM - 5PM
BEND TOP
TABS UPWARD
BEND BOTTOM
TABS DOWNWARD
DETACHABLE
FRONT PANEL
INSTALLATION INSTRUCTIONS
ISO INSTALLATIONISO INSTALLATION
ISO INSTALLATION
ISO INSTALLATIONISO INSTALLATION
REMOVE THE PLASTIC FRAME FROM THE FRONT OF THE CHASSIS BY CAREFULLY UN-SNAPPING IT.
UN-SNAP AT 2 PLACES
EACH ON TOP AND BOTTOM
PLASTIC FRAME
MAXIMUM
SCREW SIZE
M5 x 8
FACTORY MOUNTING
BRACKETS
TYPICAL INSTALLATION
MAXIMUM
SCREW SIZE
M5 x 8
2
RADIO WIRINGRADIO WIRING
RADIO WIRING
RADIO WIRINGRADIO WIRING
REFER TO PAGE 4 FOR SPEAKER WIRING
ANTENNA
RADIO WIRING
AUTOMATIC
ANTENNA
EXISTING
ANTENNA
CABLE
BLUE
IMPORTANT
THE BLUE WIRE CAN BE USED
TO REMOTELY ACTIVATE AN
AUTOMATIC ANTENNA OR AN
EXTERNAL AMPLIFIER (SEE
ANTENNA OR AMPLIFIER
MANUAL)
1.0 AMP FUSE
BLACK
10 AMP FUSE
E
FILTER
BOX
RED
SCREW
METAL PART OF DASH
(DRILL HOLE IF
NECESSARY)
YELLOW
IMPORTANT
THIS WIRE MUST BE
CONNECTED AS SHOWN
OR RADIO WILL NOT
OPERATE PROPERLY
CAR
FUSEBLOCK
"RADIO" OR
"ACCESSORY" FUSE
CAR BATTERY
POSITIVE (+) TERMINAL
12 VOLT BATTERY
3
ANTENNA LEAD
SOCKET FROM
REAR OF RADIO
4 PIN PLUG
9-PIN PLUG
RADIO
SEE PAGE 4 FOR
SPEAKER WIRING
SPESPE
AA
KK
SPE
SPESPE
ER WIRINGER WIRING
A
K
ER WIRING
AA
KK
ER WIRINGER WIRING
REFER TO PAGE 3
FOR RADIO WIRING
RCA JACKS
LINE OUT
FOR USE
WITH
OPTIONAL
EXTERNAL
AMPLIFIERS
RED=RIGHT
REAR
WHITE=LEFT
REAR
9-PIN PLUGS
LEFT FRONT SPEAKER
SPEAK ER WIRING
l
THE AMPLIFIERS IN THIS RADIO ARE ONLY DESIGNED FOR USE WITH 4 SPEAKERS.
l
NEVER COMBINE (BRIDGE) OUTPUTS FOR USE WITH 2 SPEAKERS.
l
NEVER GROUND NEGATIVE SPEAKER LEADS TO CHASSIS GROUND.
l
FAILURE TO WIRE EXACTLY AS SHOWN BELOW MAY CAUSE ELECTRICAL DAMAGE TO
THE RADIO.
RADIO
WARNING!
4-PIN PLUGS
SEE PAGE 3
FOR RADIO
WIRING
RIGHT FRONT SPEAKER
WHITE w/BLACK STRIPE
WHITE
GREEN
GREEN w/BLACK STRIPE
GRAY w/BLACK STRIPE
GRAY
VIOLET
VIOLET w/BLACK STRIPE
HELP!
1-800-645-4994
Monday - Friday
LEFT REAR SPEAKER RIGHT REAR SPEAKER
Saturday
8:30am - 7:00pm Eastern
9:00am - 5:00pm Eastern
4
Loading...