Audiovox 1285807 User Manual

OWNER'S MANUAL

MANUEL D'UTILISATION

MANUAL DEL USUARIO

ACD-16ACD-16

ACD-16

ACD-16ACD-16

DETACHABLE FRONT PANEL, AM/FM/MPX RADIO WITH COMPACT DISC

PLAYER, CD CHANGER CONTROLS

AND QUARTZ CLOCK

AUTORADIO AM/FM/MPX AVEC FAÇADE AMOVIBLE, DOTÉ D'UN LECTEUR

DE DISQUES COMPACTS, DE COMMANDES DE CHANGEUR DE CD ET D'UNE

MONTRE À QUARTZ

PANEL DELANTERO DESMONTABLE CON

RADIO AM/FM/MPX, CON REPRODUCTOR Y CAMBIADOR

DE DISCOS COMPACTOS Y RELOJ DE CUARZO

INSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONS

This unit is designed for installation in cars, trucks, and vans with an existing radio opening. In many cases, a

IONSIONS

IONS

special installation kit will be required to mount the radio to the dashboard. These kits are available at electronics

supply stores and car stereo specialist shops. Always check the kit application before purchasing to make sure the kit works with your vehicle. If you need a kit but cannot find it available, call our toll-free “HELP” line at 1-800-645-4994.

UNIVERSAL INSTALLATION PROCEDURE USING MOUNTING SLEEVE

1. Slide the mounting sleeve off of the chassis. If it is locked into position, use the removal tools (supplied) to disengage it.

2. Check the dashboard opening size by sliding the mounting sleeve into it. If the opening is not large enough, carefully cut or file as necessary until the sleeve easily slides into the opening. Do not force the sleeve into the opening or cause it to bend or bow. Check that there will be sufficient space behind the dashboard for the radio chassis.

ION INSTRUCION INSTRUC

ION INSTRUC

3. Locate the series of bend tabs along the top, bottom, and sides of the mounting sleeve. With the sleeve

fully inserted into the dashboard opening, bend as many of the tabs outward as necessary so that the

sleeve is firmly secured to the dashboard.

4. Place the radio in front of the dashboard opening so that the wiring can be brought through the mounting

ALLALL

ALL

sleeve. Follow the wiring diagram carefully and make certain all connections of the wiring harness are secure and insulated with wire nuts or electrical tape to insure proper operation of the unit. After completing the wiring connections, turn the unit on to confirm operation (ignition switch must be “on”). If unit does not

INSTINST

INST

operate, re-check all wiring until problem is corrected. NOTE: Adjust AM antenna trimmer NOW. Refer to label on right side of chassis for adjustment instructions. Once proper operation is achieved, turn off the ignition switch and proceed with final mounting of the chassis.

5. Carefully slide the radio into the mounting sleeve making sure it is right-side-up until it is fully seated and the spring clips lock it into place.

6. Attach one end of the perforated support strap (supplied) to the screw stud on the rear of the chassis using the hex nut provided. Fasten the other end of the perforated strap to a secure part of the dashboard either above or below the radio using the screw provided. Bend the strap to position it as necessary.

CAUTION: The rear of the radio must be supported with the strap to prevent damage to the dashboard

7. Test radio operation by referring to the Operating Instructions.

INSTALLATION USING KITS

1. If your vehicle requires the use of an installation kit to mount this radio, follow the instructions included with the installation kit to attach the radio to the mounting plate supplied with the kit.

2. Wire and test the radio as described in Step 4 above.

3. Install the radio/mounting plate assembly to the sub-dashboard according to the instructions of the installation kit.

4. Attach the support strap to the radio and dashboard as described in Step 6 above.

5. Replace the dashboard trim panel.

ISO INSTALLATION PROCEDURE

This unit has threaded holes in the chassis side panels which may be used with the original factory mounting brackets of some Toyota, Nissan, Mitsubishi, Isuzu, Hyundai and Honda vehicles to mount the radio to the dashboard. Please consult with your local car stereo specialist shop for assistance on this type of installation.

1. Remove the existing factory radio from its dashboard or center console mounting. Save all hardware and brackets as they will be used to mount the new radio.

2. Carefully un-snap the plastic frame from the front of the new radio chassis. Remove and discard the frame.

3. Remove the factory mounting brackets and hardware from the existing radio and attach them to the new radio. CAUTION: DO NOT EXCEED M5 X 6 MM MAXIMUM SCREW SIZE.

4. Wire the new radio to the vehicle as per step 4 above.

5. Mount the new radio assembly to the dashboard or center console using the reverse procedure of step 1.

from the weight of the radio or improper operation due to vibration.

LONGER SCREWS MAY TOUCH AND DAMAGE COMPONENTS INSIDE THE CHASSIS.

OLL-FREE INSTOLL-FREE INST

OLL-FREE INST

OLL-FREE INSTOLL-FREE INST

The installation and wiring connections for this unit are so simple, we doubt you'll need our help, but, if you do, we're here to help you. Just call our toll-free telephone assistance line at 1-800-645-4994 during the days and hours shown (U.S.A. and Canada only).

DAY

MON. - FRI. SATURDAY

NUT (5MM)

SCREW (5MM)

FASTEN THIS END TO SECURE PART OF DASHBOARD. DRILL HOLE IF NECESSARY.

NOTE: PLASTIC FRAME MUST BE REMOVED (UN-SNAP ON LEFT

AND RIGHT SIDES) TO USE REMOVAL TOOLS.

PACIFIC

5:30AM - 4PM 6AM - 2PM

UNIVERSAL INSTALLATION USING MOUNTING SLEEVEUNIVERSAL INSTALLATION USING MOUNTING SLEEVE

UNIVERSAL INSTALLATION USING MOUNTING SLEEVE

UNIVERSAL INSTALLATION USING MOUNTING SLEEVEUNIVERSAL INSTALLATION USING MOUNTING SLEEVE

PERFORATED STRAP

FASTEN THIS END TO SCREW STUD ON REAR OF CHASSIS

SCREW STUD

MOUNTING SLEEVE

ALLALL

ALL

ALLALL

MOUNTAIN

6:30AM - 5PM

7AM - 3PM

EXISTING DASH OPENING FILE EDGES TO FIT IF NECESSARY - DO NOT OVERFILE NOTE: IF DASH IS SOLID, USE REAR SIDE (WITHOUT THE LIP) OF MOUNTING SLEEVE AS A TEMPLATE & CUT OPENING

ION ASSISTION ASSIST

ION ASSIST

ION ASSISTION ASSIST

7:30AM - 6PM

8AM - 4PM

RADIO

REMOVAL TOOLS

CENTRAL EASTERN

NCENCE

NCE

NCENCE

8:30AM - 7PM

9AM - 5PM

BEND TOP TABS UPWARD

BEND BOTTOM

TABS DOWNWARD

INST

INSTINST

ALL

ALLALL

AA T

TT ION INSTRUC

ION INSTRUCION INSTRUC

TT IONS

IONSIONS

FOR PROPER OPERATION OF THE CD PLAYER, THE CHASSIS MUST BE MOUNTED WITHIN 20° OF HORIZONTAL. MAKE SURE THE UNIT IS MOUNTED WITHIN THIS LIMITATION.

REMOVE THE PLASTIC FRAME FROM THE FRONT OF THE CHASSIS BY CAREFULLY UN-SNAPPING IT.

CAUTION:

UN-SNAP ON LEFT AND RIGHT SIDES

PLASTIC FRAME

ISO INSTALLATIONISO INSTALLATION

ISO INSTALLATION

ISO INSTALLATIONISO INSTALLATION

MAXIMUM

SCREW SIZE

M5 x 6

FACTORY MOUNTING BRACKETS

SIDE VIEW

CHASSIS

20° MAX.

FRONT PANEL

TYPICAL INSTALLATION

MAXIMUM

SCREW SIZE

M5 x 6

DIO WIRINGDIO WIRING

DIO WIRING

DIO WIRINGDIO WIRING

REFER TO PAGE 4 FOR SPEAKER WIRING

ANTENNA

RADIO WIRING

AUTOMATIC

ANTENNA

EXISTING ANTENNA CABLE

BLUE (0.5 AMP FUSE) IMPORTANT

THE BLUE WIRE CAN BE USED TO REMOTELY ACTIVATE AN AUTOMATIC ANTENNA OR AN EXTERNAL AMPLIFIER (SEE ANTENNA OR AMPLIFIER MANUAL)

RED (0.5 AMP FUSE)

SCREW

BLACK

YELLOW (5 AMP FUSE)

IMPORTANT

THIS WIRE MUST BE CONNECTED AS SHOWN OR RADIO WILL NOT OPERATE PROPERLY

SEE PAGE 4 FOR SPEAKER WIRING

METAL PART OF DASH (DRILL HOLE IF NECESSARY)

CAR

FUSEBLOCK

"RADIO" OR "ACCESSORY" FUSE

CAR BATTERY

POSITIVE (+) TERMINAL 12 VOLT BATTERY

ANTENNA SOCKET ON REAR OF RADIO

RADIO

SPEAKER WIRINGSPEAKER WIRING

SPEAKER WIRING

SPEAKER WIRINGSPEAKER WIRING

REFER TO PAGE 3 FOR RADIO WIRING

RCA JACKS

LINE OUT

FOR USE WITH

OPTIONAL

EXTERNAL

AMPLIFIERS

RED=RIGHT REAR

WHITE=LEFT REAR

9-PIN PLUGS

WARNING!

l THE AMPLIFIERS IN THIS RADIO ARE ONLY DESIGNED FOR USE WITH 4 SPEAKERS.

NEVER COMBINE (BRIDGE) OUTPUTS FOR USE WITH 2 SPEAKERS.

NEVER GROUND NEGATIVE SPEAKER LEADS TO CHASSIS GROUND.

l FAILURE TO WIRE EXACTLY AS SHOWN BELOW MAY CAUSE ELECTRICAL

NOTE: CHECK WITH YOUR RAMPAGE/AUDIOVOX CAR STEREO SPECIALIST OR CALL 1-800-645-4994 FOR RECOMMENDATIONS OF THE MODELS THAT WILL WORK WITH YOUR RADIO.

RADIO

DIN CABLE (SUPPLIED WITH CD CHANGER).

8-PIN DIN SOCKET FOR CONNECTION TO OPTIONAL CD CHANGER

4-PIN PLUGS

OPTIONAL CD CHANGER

COMPACT

SPE

SPESPE

AA K

KK ER WIRING

ER WIRINGER WIRING

LEFT FRONT SPEAKER

WHITE w/BLACK STRIPE

GREEN w/BLACK STRIPE

WHITE

GREEN

SEE PAGE 3 FOR RADIO WIRING

GRAY w/BLACK STRIPE

GRAY

VIOLET

VIOLET w/BLACK STRIPE

RIGHT FRONT SPEAKER

HELP!

1-800-645-4994

Monday - Friday Saturday

LEFT REAR SPEAKER RIGHT REAR SPEAKER

8:30am - 7:00pm Eastern 9:00am - 5:00pm Eastern

+ 11 hidden pages