Audiovox 1285567 User Manual
OWNER'S MANUAL
AND INSTALLATION GUIDE
AA
V-427V-427
A
V-427
AA
V-427V-427
DETACHABLE FRONT PANEL AM/FM/MPX RADIO
WITH AUTO-REVERSE CASSETTE PLAYER,
CD CHANGER CONTROLS AND QUARTZ CLOCK
INSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONSINSTALLATION INSTRUCTIONS
This unit is designed for installation in cars, trucks, and vans with an existing radio opening. In many cases, a special
installation kit will be required to mount the radio to the dashboard. These kits are available at electronics supply stores
IONSIONS
IONSIONS
IONS
TT
TT
T
and car stereo specialist shops. Always check the kit application before purchasing to make sure the kit works with
your vehicle. If you need a kit but cannot find it available, call our toll-free “HELP” line at
1-800-645-4994.
UNIVERSAL INSTALLATION PROCEDURE USING MOUNTING SLEEVE
1. Remove the detachable front panel if it is attached to the chassis by pushing the “Release” button. Slide the mounting
sleeve off of the chassis. If it is locked into position, use the removal tools (supplied) to disengage it.
2. Check the dashboard opening size by sliding the mounting sleeve into it. If the opening is not large enough, carefully
ION INSTRUCION INSTRUC
ION INSTRUCION INSTRUC
ION INSTRUC
TT
TT
T
AA
AA
A
ALLALL
ALLALL
ALL
INSTINST
INSTINST
INST
cut or file as necessary until the sleeve easily slides into the opening. Do not force the sleeve into the opening or
cause it to bend or bow. Check that there will be sufficient space behind the dashboard for the radio chassis.
3. Locate the series of bend tabs along the top, bottom, and sides of the mounting sleeve. With the sleeve fully inserted
into the dashboard opening, bend as many of the tabs outward as necessary so that the sleeve is firmly secured to
the dashboard.
4. Place the radio in front of the dashboard opening so that the wiring can be brought through the mounting sleeve.
Follow the wiring diagram carefully and make certain all connections of the wiring harness are secure and insulated
with wire nuts or electrical tape to insure proper operation of the unit. After completing the wiring connections, attach
the front panel and turn the unit on to confirm operation (ignition switch must be “on”). If unit does not operate, recheck all wiring until problem is corrected. Once proper operation is achieved, turn off the ignition switch and proceed
with final mounting of the chassis.
5. Carefully slide the radio into the mounting sleeve making sure it is right-side-up until it is fully seated and the spring
clips lock it into place.
6. Attach one end of the perforated support strap (supplied) to the screw stud on the rear of the chassis using the hex
nut provided. Fasten the other end of the perforated strap to a secure part of the dashboard either above or below
the radio using the screw and hex nut provided. Bend the strap to position it as necessary.
CAUTION: The rear of the radio must be supported with the strap to prevent damage to the dashboard from the
weight of the radio or improper operation due to vibration.
7. Re-attach the front panel to the chassis and test radio operation by referring to the Operating Instructions for the unit.
INSTALLATION USING KITS
1. If your vehicle requires the use of an installation kit to mount this radio, follow the instructions included with the
installation kit to attach the radio to the mounting plate supplied with the kit.
2. Wire and test the radio as described in Step 4 above.
3. Install the radio/mounting plate assembly to the sub-dashboard according to the instructions of the installation kit.
4. Attach the support strap to the radio and dashboard as described in Step 6 above.
5. Replace the dashboard trimpanel.
11
1
11
ISO INSTALLATION PROCEDURE
This unit has threaded holes in the chassis side panels which may be used with the original factory mounting brackets
of some Toyota, Nissan, Mitsubishi, Isuzu, Hyundai and Honda vehicles to mount the radio to the dashboard. Please
consult with your local car stereo specialist shop for assistance on this type of installation.
1. Remove the existing factory radio from its dashboard or center console mounting. Save all hardware and brackets
as they will be used to mount the new radio.
2. Carefully un-snap the plastic frame from the front of the new radio chassis. Remove and discard the frame.
3. Remove the factory mounting brackets and hardware from the existing radio and attach them to the new radio.
CAUTION : DO NOT EXCEED M5 X 8 MM MAXIMUM SCREW SIZE.
LONGER SCREWS MAY TOUCH AND DAMAGE COMPONENTS INSIDE THE CHASSIS.
4. Wire the new radio to the vehicle as per step 4 above.
5. Mount the new radio assembly to the dashboard or center console using the reverse procedure of step 1.
TT
oll-Froll-Fr
T
oll-Fr
TT
oll-Froll-Fr
The installation and wiring connections for this unit are so simple, we doubt you'll need our help, but, if you do, we're
here to help you. Just call our toll-free telephone assistance line at 1-800-645-4994 during the days and hours shown
(U.S.A. and Canada only).
DAY
MON.-FRI.
SATURDAY
PACIFIC
5:30AM - 4PM
6AM - 2PM
ee
e Inse Ins
tt
e
e Ins
ee
e Inse Ins
allatallat
t
allat
tt
allatallat
MOUNTAIN
6:30AM - 5PM
7AM - 3PM
ion Asion As
ion As
ion Asion As
TIME ZONE
sissis
tt
ancanc
sis
sissis
7:30AM - 6PM
8AM - 4PM
ee
t
anc
e
tt
ancanc
ee
CENTRAL
EASTERN
8:30AM - 7PM
9AM - 5PM
UNIVERSAL INSTALLATION USING MOUNTING SLEEVE
EXISTING DASH OPENING (FILE EDGES TO FIT IF NECESSARY-DO NOT OVERFILE)EXISTING DASH OPENING (FILE EDGES TO FIT IF NECESSARY-DO NOT OVERFILE)
EXISTING DASH OPENING (FILE EDGES TO FIT IF NECESSARY-DO NOT OVERFILE)
EXISTING DASH OPENING (FILE EDGES TO FIT IF NECESSARY-DO NOT OVERFILE)EXISTING DASH OPENING (FILE EDGES TO FIT IF NECESSARY-DO NOT OVERFILE)
NOTENOTE
: IF DASH IS SOLID, USE MOUNTING SLEEVE AS A TEMPLATE & CUT OPENING: IF DASH IS SOLID, USE MOUNTING SLEEVE AS A TEMPLATE & CUT OPENING
NOTE
: IF DASH IS SOLID, USE MOUNTING SLEEVE AS A TEMPLATE & CUT OPENING
NOTENOTE
: IF DASH IS SOLID, USE MOUNTING SLEEVE AS A TEMPLATE & CUT OPENING: IF DASH IS SOLID, USE MOUNTING SLEEVE AS A TEMPLATE & CUT OPENING
NUTNUT
NUT
NUTNUT
SCREWSCREW
SCREW
SCREWSCREW
PERFORATED STRAPPERFORATED STRAP
PERFORATED STRAP
PERFORATED STRAPPERFORATED STRAP
FASTEN THIS END TOFASTEN THIS END TO
FASTEN THIS END TO
FASTEN THIS END TOFASTEN THIS END TO
SCREW STUD ONSCREW STUD ON
SCREW STUD ON
SCREW STUD ONSCREW STUD ON
REAR OF CHASSISREAR OF CHASSIS
REAR OF CHASSIS
REAR OF CHASSISREAR OF CHASSIS
BEND TOP TABSBEND TOP TABS
BEND TOP TABS
BEND TOP TABSBEND TOP TABS
UPWARD UPWARD
UPWARD
UPWARD UPWARD
RADIORADIO
RADIO
RADIORADIO
SCREW STUDSCREW STUD
SCREW STUD
SCREW STUDSCREW STUD
BEND BOTTOM TABSBEND BOTTOM TABS
BEND BOTTOM TABS
BEND BOTTOM TABSBEND BOTTOM TABS
DOWNWARDDOWNWARD
DOWNWARD
DOWNWARDDOWNWARD
INST
INSTINST
INSTINST
ALL
ALLALL
ALLALL
A
AA
AA
T
TT
TT
ION INSTRUC
ION INSTRUCION INSTRUC
ION INSTRUCION INSTRUC
T
TT
TT
IONS
IONSIONS
IONSIONS
MOUNTING SLEEVE MOUNTING SLEEVE
MOUNTING SLEEVE
MOUNTING SLEEVE MOUNTING SLEEVE
FASTEN THIS END TO SECURE PARTFASTEN THIS END TO SECURE PART
FASTEN THIS END TO SECURE PART
FASTEN THIS END TO SECURE PARTFASTEN THIS END TO SECURE PART
OF DASHBOARD.OF DASHBOARD.
OF DASHBOARD.
OF DASHBOARD.OF DASHBOARD.
DRILL HOLE IF NECESSARY.DRILL HOLE IF NECESSARY.
DRILL HOLE IF NECESSARY.
DRILL HOLE IF NECESSARY.DRILL HOLE IF NECESSARY.
ISO INSTALLA TION
REMOVE THE PLASTIC FRAME FROM THEREMOVE THE PLASTIC FRAME FROM THE
REMOVE THE PLASTIC FRAME FROM THE
REMOVE THE PLASTIC FRAME FROM THEREMOVE THE PLASTIC FRAME FROM THE
FRONT OF THE CHASSIS BY CAREFULLYFRONT OF THE CHASSIS BY CAREFULLY
FRONT OF THE CHASSIS BY CAREFULLY
FRONT OF THE CHASSIS BY CAREFULLYFRONT OF THE CHASSIS BY CAREFULLY
UN-SNAPPING IT.UN-SNAPPING IT.
UN-SNAPPING IT.
UN-SNAPPING IT.UN-SNAPPING IT.
UN-SNAP AT 2 PLACESUN-SNAP AT 2 PLACES
UN-SNAP AT 2 PLACES
UN-SNAP AT 2 PLACESUN-SNAP AT 2 PLACES
EACH ON TOP ANDEACH ON TOP AND
EACH ON TOP AND
EACH ON TOP ANDEACH ON TOP AND
BOTTOMBOTTOM
BOTTOM
BOTTOMBOTTOM
PLASTIC FRAMEPLASTIC FRAME
PLASTIC FRAME
PLASTIC FRAMEPLASTIC FRAME
TYPICAL INSTALLATION TYPICAL INSTALLATION
TYPICAL INSTALLATION
MAX. SIZEMAX. SIZE
MAX. SIZE
MAX. SIZEMAX. SIZE
M5 x 8M5 x 8
M5 x 8
M5 x 8M5 x 8
FACTORY MOUNTING BRACKETSFACTORY MOUNTING BRACKETS
FACTORY MOUNTING BRACKETS
FACTORY MOUNTING BRACKETSFACTORY MOUNTING BRACKETS
TYPICAL INSTALLATION TYPICAL INSTALLATION
REMOVALREMOVAL
REMOVAL
REMOVALREMOVAL
TOOLS TOOLS
TOOLS
TOOLS TOOLS
DETACHABLEDETACHABLE
DETACHABLE
DETACHABLEDETACHABLE
FRONT PANELFRONT PANEL
FRONT PANEL
FRONT PANELFRONT PANEL
MAX. SIZEMAX. SIZE
MAX. SIZE
MAX. SIZEMAX. SIZE
M5 x 8M5 x 8
M5 x 8
M5 x 8M5 x 8
22
2
22
RR
AA
DIO WIRINGDIO WIRING
R
A
DIO WIRING
RR
AA
DIO WIRINGDIO WIRING
REFER TO PAGE 4 FOR SPEAKER WIRING
DIO WIRINGDIO WIRING
DIO WIRINGDIO WIRING
DIO WIRING
AA
AA
A
RR
RR
R
ANTENNAANTENNA
ANTENNA
ANTENNAANTENNA
AUTOMATICAUTOMATIC
AUTOMATIC
AUTOMATICAUTOMATIC
ANTENNAANTENNA
ANTENNA
ANTENNAANTENNA
EXISTINGEXISTING
EXISTING
EXISTINGEXISTING
ANTENNAANTENNA
ANTENNA
ANTENNAANTENNA
CABLECABLE
CABLE
CABLECABLE
BLUEBLUE
BLUE
BLUEBLUE
IMPORTANTIMPORTANT
IMPORTANT
IMPORTANTIMPORTANT
THE BLUE WIRE CAN BE USED TO
REMOTELY ACTIVATE AN AUTOMATIC ANTENNA OR AN EXTERNAL
AMPLIFIER (SEE ANTENNA OR AMPLIFIER MANUAL)
REDRED
RED
REDRED
SCREWSCREW
SCREW
BLACKBLACK
BLACK
BLACKBLACK
SCREWSCREW
METAL PART OF DASHMETAL PART OF DASH
METAL PART OF DASH
METAL PART OF DASHMETAL PART OF DASH
(DRILL HOLE IF NECESSARY)(DRILL HOLE IF NECESSARY)
(DRILL HOLE IF NECESSARY)
(DRILL HOLE IF NECESSARY)(DRILL HOLE IF NECESSARY)
FUSEBLOCKFUSEBLOCK
FUSEBLOCK
FUSEBLOCKFUSEBLOCK
“RADIO” FUSE“RADIO” FUSE
“RADIO” FUSE
“RADIO” FUSE“RADIO” FUSE
+ 12V ACCESSORY+ 12V ACCESSORY
+ 12V ACCESSORY
+ 12V ACCESSORY+ 12V ACCESSORY
CAR BATTERYCAR BATTERY
CAR BATTERY
CAR BATTERYCAR BATTERY
33
3
33
ANTENNA LEAD ONANTENNA LEAD ON
ANTENNA LEAD ON
ANTENNA LEAD ONANTENNA LEAD ON
REAR OF RADIOREAR OF RADIO
REAR OF RADIO
REAR OF RADIOREAR OF RADIO
YELLOWYELLOW
YELLOW
YELLOWYELLOW
IMPORTANTIMPORTANT
IMPORTANT
YELLOW WIRE MUST BE CONNECTED AS SHOWNYELLOW WIRE MUST BE CONNECTED AS SHOWN
YELLOW WIRE MUST BE CONNECTED AS SHOWN
YELLOW WIRE MUST BE CONNECTED AS SHOWNYELLOW WIRE MUST BE CONNECTED AS SHOWN
OR RADIO WILL NOT OPERATE PROPERLY OR RADIO WILL NOT OPERATE PROPERLY
OR RADIO WILL NOT OPERATE PROPERLY
OR RADIO WILL NOT OPERATE PROPERLY OR RADIO WILL NOT OPERATE PROPERLY
RADIORADIO
RADIO
RADIORADIO
IMPORTANTIMPORTANT
4 PIN PLUGS4 PIN PLUGS
4 PIN PLUGS
4 PIN PLUGS4 PIN PLUGS
9 PIN PLUG9 PIN PLUG
9 PIN PLUG
9 PIN PLUG9 PIN PLUG
(SEE PAGE 4 FOR SPEAKER WIRING)(SEE PAGE 4 FOR SPEAKER WIRING)
(SEE PAGE 4 FOR SPEAKER WIRING)
(SEE PAGE 4 FOR SPEAKER WIRING)(SEE PAGE 4 FOR SPEAKER WIRING)
POSITIVE (+) TERMINALPOSITIVE (+) TERMINAL
POSITIVE (+) TERMINAL
POSITIVE (+) TERMINALPOSITIVE (+) TERMINAL
12V BATTERY12V BATTERY
12V BATTERY
12V BATTERY12V BATTERY
Loading...