Audiovox 128-4638D User Manual
Model APS 600
Installation Manual
Note : The method of manual override can either be selected to operate from the valet switch or operate as custom code. Be
certain to place a check mark indicating the method used in the box located on the last page of the owner's manual.
Dip Switch Selectable Features :
SELECTABLE FEATURES
Switch Number ON Position OFF Position Factory Default
Dip Switch 1 Custom Code Override Valet Switch Override Custom Code Override
Dip Switch 2 Voltage Sense Hardwire Voltage Sense
Note : When both Passive Arming and Voltage Sensing are selected, you must hardwire the driver’s door pin switch in order to
begin the passive arming sequence.
RF Programmable Features :
Feature Selection 1 Chirp 2 Chirps Default
First 1 Second Door Locks 3.5 Second Door Locks 1 Second
Second Auto Lock On Auto Lock Off Auto Lock Off
Third Auto Unlock On Auto Unlock Off AutoUnlock Off
Fourth Headlight Output On Headlight Output Off Headlight On
Fifth Passive Door Locks Active Door Locks Passive Locks
Sixth Passive Arming Active Arming Active Arming
To program these selectable features;
Action System Response
Turn ignition on No response
Flip valet switch on then off 3 times 1 Chirp - LED 1 flash
Within 3 seconds, turn ignition Off Short chirp, then long chirp
First Then On 1 chirp = 1 second door locks
Second Flip valet switch on then off 2 chirps = auto locks off
Third Flip valet switch on then off 2 chirps = auto unlock off
Fourth Flip valet switch on then off 1 chirp = headlight output on
Fifth Flip valet switch on then off 1 chirp = passive locks
Sixth Flip valet switch on then off 1 chirp = passive arming
Press transmitter button 1 to change 2 chirps = 3.5 second door locks
or
Press tranmitter button 1 to change 1 chirp = auto locks on
or
Press transmitter button 1 to change 1 chirp = auto unlock on
or
Press transmitter button 1 to change 2 chirps = headlight output off
or
Press transmitter button 1 to change 2 chirps = active locks
or
Press transmitter button 1 to change 2 chirps = active arming
Flip valet switch on then off Exit program mode
Turn ignition key off Exit program mode
Note : Once you enter the feature programming mode, do not allow more than 15 seconds to pass between steps, or the program-
ming will be terminated.
or
or
Page 1
INSTALLATION OF MAJOR COMPONENTS
Control Module :
Select a mounitng location inside the passenger compartment ( up behind the dash ), and secure using
the two screws provided. The control module can also be secured in place using cable ties.
Do not mount the control module in the engine compartment, as it is not waterproof. You should also
avoid mounting the unit directly onto factory installed electronic components. These components may
cause RF interference, which can result in poor transmitter range or intermittent operation.
Siren :
Select a mounting location in the engine compartment that is well protected from access below the
vehicle. Avoid areas near high heat components or moving parts within the engine compartment. To
prevent water retention, the flared end of the siren must be pointed downward when mounted.
Mount the siren to the selected location using the screws and bracket provided.
Hood or Trunk Pin Switch :
A pin switch is included for use in protecting the hood or trunk ( or hatchback ) of the vehicle. The switch
must always be mounted to a grounded, metal surface of the vehicle. It is important to select a location
where water cannot flow or collect, and to avoid all drip gutters on hood and trunk fender walls. Choose
locations that are protected by rubber gaskets when the hood or trunk lid is closed.
The pin switch can be mounted using the bracket provided, or direct mounted by drillinga¼“diameter
mounting hole. Keep in mind that when properly mounted, the plunger of the pin switch should depress
at least ¼ “ when the hood or trunk lid is closed.
Dash Mounted L.E.D. :
A small red L.E.D. is included that will serve as a visual indicator of the alarm status. It should be
installed in the dash, located where it can be easily seen from outside the vehicle, yet not be distracting
to the driver.
Once a location has been selected, check behind the panel for wire routing access, and to confirm the
drill will not damage any existing components as it passes through the panel.
Drilla¼“diameter hole, and pass the red and blue wires from the L.E.D. through the hole, from the front
of the panel. Firmly press the body of the L.E.D. into the hole until fully seated.
Valet Switch :
Select a mounting location for the switch that is easily accessible to the driver of the vehicle. The switch
does not have to be concealed, however, concealing the switch is always recommended, as this provides an even higher level of security to the vehicle.
The valet switch can be mounted to the lower side of the dash by drillinga¼“diameter hole in the
selected location.
Be sure to check behind the dash for adequate clearance for the body of the switch, and to confirm that
the drill will not damage any existing components as it passes through the dash. You should also make
certain that the back of the switch is accessible for wiring later in the installation.
Shock Sensor :
Select a solid mounting surface for the shock sensor on the firewall inside the passenger compartment,
and mount the sensor using the two screws provided. The shock sensor can also be secured to any fixed
brace behind the dash using tie straps.
Whichever mounting method is selected, make certain that the sensitivity adjustment is accessible for
use later in the installation.
Page 2
WIRING THE SYSTEM
Large 10 Pin Edge Connector :
Red Fused Wire : + 12 VDC CONSTANT BATTERY SOURCE
This wire controls the sensitivity of the voltage sensing circuit, which detects the turning on of an interior
light when a door is opened. It will also detect the switching on of parking or headlamps, and in many
cases will trigger the alarm when a thermostatically controled electronic radiator cooling fan switches on.
When installing this system into vehicles with electronic “ after fans “, it is recommended you disable the
voltage sense circuit.
In voltage sensing applications, the closer to the battery that the red wire is connected, the less sensitive
the voltage sense circuitry will be. Moving this connection point to the fuse panel will increase the sensitivity, and connecting to the courtesy lamp fuse in the vehicle will provide maximum sensitivity of the
voltage sense circuit.
When hardwiring the control module to pin switches at all entry points, the voltage sense circuit must be
disabled. Move dip switch#2totheoffposition, then connect the red wire toa+12VDCconstant battery
source.
White Wire : + 12 VDC PULSED PARKING LIGHT OUTPUT ( 15 Amp Max )
This wire is provided to flash the vehicle’s parking lights. Connect the white wire to the positive side of
one of the vehicle’s parking lights.
Orange Wire : 300 mA GROUND OUTPUT WHEN ARMED - N. C. STARTER DISABLE
This wire is provided to control the starter cut relay. Connect the orange wire to terminal 86 of the relay.
Connect relay terminal 85 to an ignition wire in the vehicle that is live when the key is in the on and crank
positions, and off when the key is in the off position. ( This is where the yellow wire from the alarm should
be connected ).
Cut the low current starter solenoid wire in the vehicle, and connect one side of the cut wire to relay
terminal 87A. Connect the other side of the cut wire to relay terminal 30.
Note : This is a normally closed starter cut arrangement, and when power is removed from the
security system, the starter disable feature will not operate, allowing the vehicle to start.
Audiovox does not recommend using the Orange wire to interrupt anything but the starting circuit of the vehicle.
2 Dark Blue Wires : DELAYED PULSED OUTPUT / CHANNEL 2 ( TRUNK RELEASE )
The dark blue wires are controlled via an independent RF channel from the keychain transmitter. These
are the N.O. and COMMON contacts of an on board, 10 Amp relay, so they can be connected to positive
or negative switched circuits.
Connect one of the dark blue wires to the output of the trunk release pushbutton switch, and the other
dark blue wire to either chassis ground, or to a fused + 12 VDC battery source, depending on the polarity
of the trunk release circuit in the vehicle.
When using this channel for an accessory other than trunk release, connect one dark blue wire to the
accessory, and the other dark blue wire to either chassis ground, or, to a fused + 12 volt battery source,
depending upon the requirements of the accessory.
WARNING ! Never attempt to pull more than 10 Amperes of current through this relay. The circuit
will be damaged. Always check the requirements of accessories prior to connecting
them to the circuit.
Black Wire : CHASSIS GROUND
Connect this wire to a solid, metal part of the vehicle’s chassis. Do not confuse this wire with the thin black
antenna wire that exits the control module independently.
Page 3
2 Dark Green w/ White Trace Wires : ENTRY ILLUMINATION
The dark green w/ white trace wires provide the entry lighting, and flash the vehicle’s dome light while the
alarm is sounding. These are NO ( normally open ) and COM ( common ) contacts of an on board, 10
Amp maximum relay.
Connect one of the dark green w/ white trace wires to the wire in the vehicle that turns on the interior
courtesy light. Connect the other dark green w/ white trace wire to either chassis ground if the vehicle
switches ground to the courtesy lights, or a fused + 12 volt constant battery source if the vehicle
switches 12 volts to the courtesy lights.
NOTE : When wiring this feature in vehicles with factory equipped delay lighting circuits, it is
best to connect to the output of the timer which feeds the dome light, rather than at the
door switch. This will ensure that the dome light pulses when the alarm is triggered.
White w/ Black Trace Wire : POSITIVE OUTPUT TO SIREN
Route this wire through a rubber grommet in the firewall, and to the siren location.
Connect the white / black wire to the positive wire of the siren. Secure the black ground wire of the siren
to chassis ground.
Mini 10 Pin Edge Connector :
Light Green Wire : ( - ) INSTANT TRIGGER ZONE 1
This is an instant on ground trigger wire. This wire ( zone ) should be reserved for connection to optional
ground output trigger devices such as motion and / or shock impact sensors.
White w/ Blue Trace Wire : HEADLIGHT OUTPUT - ARM & DISARM
The white w/ blue trace wire is provided to control the optional headlight illumination feature of the
system. This is a transistorized, low current ( 300 mA ) output, and should only be used to drive an
external relay coil.
This wire provides a 30 second ground signal whenever the system is remotely armed or disarmed..
Connect the white w/ blue trace wire to terminal 86 of the AS 9256 relay ( or an equivalent 30 Amp
automotive relay ), and connect relay terminal 85 to a fused + 12 VDC battery source. Connect relay
terminal 87 to one of the low beam headlight wires in the vehicle, and connect relay terminal 30 to
either chassis ground or a fused ( 15 Amp Min)+12VDCbattery source, depending on the polarity of
the headlight circuit in the vehicle.
Yellow Wire : + 12 VDC IGNITION SOURCE
Connect this wire to a source that is live when the key is in the on and crank positions. Be sure that this
source is off when the key is in the off position.
Purple Wire : + DOOR TRIGGER
If the vehicle’s door courtesy light switches havea+12volt output when the door is opened ( most
Fords and some Imports ), you must connect this wire to the positive output from one of the door
switches. In most cases, the purple wire will only need to be connected to one door switch, no matter
how many doors the vehicle has.
WARNING : Do not use the purple wire if the vehicle has ground output type door switches. ( see Brown
Wire ).
Brown Wire : - DOOR TRIGGER
If the vehicle’s courtesy light switches havea(-)ground output when the door is opened ( GM and
most Imports ), you must connect this wire to the negative output from one of the door switches.
WARNING : Do not use the brown wire if the vehicle has + 12 volt output type door switches. ( see
Purple Wire ).
Page 4
Dark Green Wire : ( - ) INSTANT TRIGGER ZONE 2
This is an instant on ground trigger wire. It must be connected to the previously installed hood and trunk pin
switches.
Orange w/ White Trace Wire:300mA GROUND OUTPUT WHEN DISARMED-N.O. STARTER DISABLE
This wire is provided to control the starter cut relay. Connect the orange w/white wire to terminal 86 of the
relay. Connect relay terminal 85 to an ignition wire in the vehicle that is live when the key is in the on and
crank positions, and off when the key is in the off position. ( This is where the yellow wire from the alarm
should be connected ).
Cut the low current starter solenoid wire in the vehicle, and connect one side of the cut wire to relay
terminal 87. Connect the other side of the cut wire to relay terminal 30.
Note : This is a normally opened starter cut arrangement, and when power is removed from the
security system, the starter disable feature will remain operational, and the vehicle will not
start. Audiovox does not recommend using the Orange w/ White trace wire to interrupt
anything but the starting circuit of the vehicle.
Black w/ White Trace Wire : 300 mA HORN OUTPUT
The black w/ white trace wire is provided to beep the vehicle’s horn. This is a transistorized low current
output, and should only be connected to the low current ground output from the vehicle’s horn switch.
If the vehicle usesa+12VDChorn switch, then connect the black w/ white trace wire to terminal 86 of the
AS 9256 relay ( or an equivalent 30 Amp automotive relay ), and connect relay terminal 85 to a fused + 12
VDC battery source. Connect relay terminal 87 to the vehicle’s horn switch output, and connect relay
termianl 30 to a fused + 12 VDC battery source.
Dark Green w/ Black Trace Wire : LATCHING OUTPUT / CHANNEL 3
The green w/ black trace wire latches to ground via an independant RF channel from the keychain transmitter. This is a transistorized, low current ( 300 mA ) output, and should only be used to drive an external
relay coil.
This wire provides an immediate ground signal, and stays at ground for as long as the button(s) on the
keychain transmitter remain pressed.
WARNING ! Connecting the dark green w/ black trace wire to the high current switched output of
trunk release circuits will damage the control module.
Connect the dark green w/ black trace wire to terminal 86 of the AS 9256 relay ( or an equivalent 30 Amp
automotive relay ), and wire the remaining relay contacts to perform the selected function of channel 3.
Light Blue Wire : LATCHING OUTPUT / CHANNEL 4
The light blue wire latches to ground via an independant RF channel from the keychain transmitter. This is
a transistorized, low current ( 300 mA ) output, and should only be used to drive an external relay coil.
This wire provides an immediate ground signal, and stays at ground for as long as the button(s) on the
keychain transmitter remain pressed.
WARNING ! Connecting the light blue wire to the high current switched output of trunk release
circuits will damage the control module.
Connect the light blue wire to terminal 86 of the AS 9256 relay (or an equivalent 30 Amp automotive
relay), and wire the remaining relay contacts to perform the selected function of channel 4.
2 Pin Blue Connector : VALET SWITCH
Route the grey and black wires in the 2 pin connector from the valet switch to the control module, and plug
it into the mating blue connector on the side of the module.
Page 5
2 Pin White Connector : DASH MOUNTED L.E.D.
Route the red and blue wires in the 2 pin white connector from the L.E.D. to the control module, and plug
it into the mating white connector on the side of the module.
4 Pin White Connector : SHOCK SENSOR
Route the red, black, blue, and green wires in the 4 pin white connector from the shock sensor to the
control module, and plug one end into the shock sensor, and the other end into the mating white connector on the side of the module.
NORMAL DOOR LOCK OPERATION
6 Pin Door Lock Output Connector :
The orange, blue w/ white tracer, yellow, white, green, and blue wires in the 6 conductor connector are
the contacts of the on board door lock relays. The function of each of these wires is listed below;
Lock Relay Unlock Relay
Blue w/ White Trace = N.O. Relay Contact Orange = N.O. Relay Contact
Dark Green = N.C. Relay Contact Dark Blue = N.C. Relay Contact
Yellow = Common Relay Contact White = Common Relay Contact
3 Wire Ground Switched Door Lock Circuits :
In these vehicles, the dark green and dark blue door lock wires are not used.
The white and yellow wires must be connected to a chassis ground source.
The blue w/ white stripe wire is the ground pulse “ lock “ output, and should be connected to the negative
lock wire in the vehicle.
The orange wire is the ground pulse “ unlock “ output, and should be connected to the negative unlock
wire in the vehicle.
3 Wire Positive Switched Door Lock Circuits :
In these vehicles, the dark green and dark blue wires are not used.
The orange and blue w/ white stripe wires must be connected toa+12volt battery source.
The yellow wire is the positive pulse “ lock “ output, and should be connected to the positive lock wire in
the vehicle.
The white wire is the positive pulse “ unlock “ output, and shouls be connected to the positive unlock wire
in the vehicle.
5 Wire Alternating Door Lock Circuits :
In this application, it is necessary to cut the existing door lock by - pass wires. These wires run from the
master door lock switch to the slave door lock switch, and then on to the door lock motors.
Cut the existing lock wire, and connect the yellow wire to the slave switch or motor side of the cut wire.
Connect the green wire to the master switch side of the cut wire.
Cut the existing unlock wire, and connect the white wire to the slave switch or motor side of the cut wire.
Connect the blue wire to the master switch side of the cut wire.
The orange and blue w/ white stripe wires must be connected to a fused + 12 VDC battery source.
Refer to the door lock wiring supplement for proper connection of these wires into the various locking
circuits available in current vehicles.
Page 6
2 STEP UNLOCK OPERATION
6 Pin Door Lock Output Connector :
When wiring for 2 step unlock operation, you must connect the outputs of the on board unlock relay to the
driver’s door lock motor. Wire these outputs as follows;
Orange = N.O. Relay Contact to + 12 VDC Battery
Dark Blue = N.C. Relay Contact to Motor leg switch side
White = Common Relay Contact to Motor leg motor side
Wire the transistorized negative “ all doors unlock “ output directly to the negative unlock wire from the
door lock switch in vehicles with 3 wire ground switched circuits.
In vehicles with 3 wire positive or 5 wire alternating switched circuits, you must add a 30 Amp automotive
relay to provide the “ all doors unlock “ feature.
Red w/ Black & Green w/ Black 2 Pin Red Connector : 2 STEP UNLOCK CONNECTOR
The green w/ black tracer wire provides a 300 mA ground pulse output for the all doors unlock signal, and
can be connected to the negative door unlock wire in 3 wire negative switched vehicles.
The red w/ black trace wire provides a low current (300 mA) + 12 VDC source for those applications that
require a relay for the all doors unlock feature. This wire should be connected to the relay coil only. A
separate +12 VDC source must be used for the high current relay contacts.
COMPLETING THE INSTALLATION
Antenna Wire : Be sure to extend the thin black antenna wire to it’s full length, and cable tie into place
where it cannot be damaged. Avoid wrapping this wire around major, high current wire looms.
Adjusting the Shock Sensor : The sensitivity of the pre - detect circuit is automatically set 30% less
sensitive than the full trigger circuit.
Using a small screwdriver, gently turn the adjustment screw fully counterclockwise. ( DO NOT over turn
this screw. Maximum rotation for this adjustment is 270° ). Close the hood and trunk lids, and arm the
alarm. Wait 6 seconds for the accessories trigger zone to stabilize, then firmly strike the rear bumper with
the side of a closed fist considering the amount of force required to break a window.
CAUTION : Never perform this test on the vehicle’s glass, as you may break the window.
Turn the adjustment screw clockwise ( increasing sensitivity ) about ¼ turn and re - test. Repeat this
procedure until the alarm sounds. Ultimately, one firm strike to the rear bumper will cause the alarm to
emit pre - detect warning tones.
WARNING ! Setting the sensitivity too high can cause false alarms due to noise vibrations from passing
trucks and heavy equipment. To decrease sensitivity, turn the adjustment screw counter
clockwise.
Wire Dressing : Always wrap the alarm wires in convoluted tubing, or with a spiral wrap of electrical tape.
Secure these looms along the routing using cable ties. This will ensure that the alarm wires are not
damaged by falling onto hot or sharp moving surfaces in the vehicle.
Operation : Take a few moments to check off the appropriate option boxes in the owner’s manual, and to
fully explain the operation of the system to your customer.
Audiovox Corp., 150 Marcus Blvd., Hauppauge, N.Y. 11788
Page 7
128-4638D
SIREN
WHITE w/BLACK
BLACK
SHOCK SENSOR
Red, Black, Blue, and
Green WIres.
BLACK
GREEN w/WHITE
ENTRY ILLUMINATION
Connect to +12 VDC Battery
for Positive Switched Dome
Light or Chassis Ground for
Negative Switched Dome Light
DOOR PIN SWITCH
DOME LIGHT
GREEN w/WHITE
GROUND SOURCE
Connect to Vehicle's Chassis
EXISTING
BLACK
(-) TO VEHICLE'S
CHASSIS GROUND
RED w/
WHITE
5A
FUSE
RED
RED
15A
FUSE
+12 VDC BATTERY
Connect to a +12 Volt
Battery Source.
(See Note on Voltage
Sensing)
EXISTING PARKING LIGHT
APS-600
CONTROL MODULE
GREEN
WHITE
YELLOW
BLUE w/WHITE
BLUE
ORANGE
DOOR LOCK
OUTPUTS
TRUNK RELEASE
Connect to +12 VDC Battery for
Positive Switched Trunk Release
or
Chassis Ground for Negative
Switched Trunk Release
EXISTING TRUNK
RELEASE SWITCH
EXISTING SWITCHED
OUTPUT
DARK BLUE
DARK BLUE
Page 8
WHITE
ORANGE
EXISTING LOW CURRENT SOLENOID
FEED WIRE (+12VDC, CRANKING ONLY)
TO
START
SOLENOID
RED
TO +12 VDC
IGN./CRANK
85
87
87A
CUT
30
86
TO
IGNITION
SWITCH
CHANNEL 4
Negative Latching Output
for Optional Remote Start
or Window Roll-Up
APS-600
CONTROL MODULE
LT. BLUE
GREEN w/BLACK
CHANNEL 3
Negative Latching Output
for Optional Remote Start
or Window Roll-Up
BLACK w/WHITE
HORN OUTPUT
Connect to Low Current Negative
Wire from Horn Switch
GROUND OUTPUT
when DISARMED
Connect To Relay For
Normally Opened Starter-
Cut Fearture
HOOD OR TRUNK
PIN SWITCH
ORANGE w/WHITE
GREEN w/
BLACK
RED
LT. BLUE
LT. GREEN
VALET SWITCH
GREY
BLACK
RED w/
BLACK
2 STEP UNLOCK
RELAY OUTPUTS
To Relay Terminal #85
To Relay Terminal #86
L.E.D.
ZONE 1
Optional Negative Triggering
AlarmAccessories
EXISTING
DOME LIGHT
+
DARK GREEN
EXISTING
NEGATIVE SWITCHING
DOOR PIN SWITCH (GM TYPE)
BROWN
EXISTING DOME LIGHT
-
Page 9
PURPLE
WHITE w/BLUE
YELLOW
HEADLIGHT OUTPUT
30 Second Ground Output
During Arm & Disarm
(Optional Relay Required)
IGNITION SOURCE
To +12 Volts
Ignition / Crank
+
Loading...