Audio Telex ATC5488 Installation
ATC5488 TONE
you
Thank
Evacuatim and Al€rt
Audio Telex
module and a rec€ptacle, already installed
for choosing an Audio Telex
Tones, both to A52220.1-2
manufuchred mixer or amplifier
GENERATOR
MODULE
INSTALLATION I NSTRUCTIONS
ATC5488 tone
standards, as
is made simple by utilising a standard
into the mixer or amplifier. Please follow these easy instructions for installation.
generator
well
module. The ATC5488 has four tones available. These are
as a Bell Tone and
a Pre Announce
qpe
'€nd'
connector
Chime.
lnstallation into
plug
any
supplied on the
E The installation
rttemptcd by a
to scc.ss thc inside
qualified
For
installation into an
heat
sink
towards
the
For installation into an
the reble
towards the right
For
installation into an
betweer
conneclor exit towards the rear
For
on
mixcr-
For
input
connector exit towards the rear
input
lnstallatlon into a
the mixer PCB. Comect the module to
installaUon lnto a
Ch. 8
technicirn
when
looking from the front
rear
ofthe amplifier.
pot
and the master
Ch. 6
pot
of lhe ATC548E involvcs eccess to
qualifed
technicirn. Alwlys
of lhcsc
amplifier:
lC30
AT SERIES amplmer:
volume
hand side ofthe amplifier when
SA SERIES amplifier: Locate the ernpty 7
pot
and the bass tonal contol
ofthe amplifier.
TX6000
TX8200 stereo mlxer: Locate the
and the Left
Channel Mast€r out
ofthe mixer.
inside
thc
turn off the AC
prodlcts.
Plerse contrct
your
'
Locate the empty 7
panel.
pot.
or
Connect the module to this receptacle, ensuring that the wires from the connector
Lo€ate the empty 7
Connect the module
looking from tlre front
pot.
Connect
TX8000 mlxer: Locate the empty 7
this receptaclg ensruing that the wires from the connector
pot.
Connect the module
pin
'and'
lo this receptacle, orsuring that the wires from the connector exit
the
eflpty
of the rmplitrers
power
and rcmove the AC
Errest Audio
connector
pin
'end'
panel.
pin
module to this receptacle, ensuring
pin
'end'
pin
7
'end'
to this receptacle, ensuring that the wtes from
or mixerg Inst tlrtion
power
Telex
oftce for
receptacle on the mixer PCB to the left
connector receptacle on the mixer PCB between
'end' connector receptacle on the mixer PCB
connector receptacle behind input
exit
corulector receptacle on the mixer PCB b€tween
should only bc
cord bcfore attempting
detdls
that the wires
towards the rear
of
your
trefcat
of the
exit
from the
pot
Ch. 5
of the
the
Connectlon to ampllfler:
Connectlons to swltched
Trim Pot Note
urti-clockwise fashion ie,
allow full signal
that the tim
present
though to
hnned
signal:
pot
located
fully
the
Connections
Orange=
:
Black
Blue
=
Red = DC Supply
Black = Common
White
=
Yellow: Bell
Purple
=
Blue
=
positim
in
clockwise will completely
amplifier
RlO on the module attenuates the level out of the
stage.
Output
Grormd
Mute switch to I
(Min.
Evac,uation Tone
Tone
Alert Tone
Pre Annormce
Chime
Notes
att€nuate
the signal
I2VDC, Max. t SVDC)
whilst
outpl$
ATC5488
hrned fully anti-clockwise
and works in an
r\'.1 ri
will
TONE IIODULE
ILACK
I,IHIIE
YB.LII,
PURPLE . ALERT
DLIJE
CEHMEN
=
.
EVAC
BELL
=
PRE
'
ANNT]UNCE
TRI
POT Rlo
ATC54B8
LEVA- rlUT
=
TINE
ORANGE
BLACK -
ELUE
RE!
oln
MEDULE
OU]PUT
=
@IruND
I{UTE
=
-
DC SUPPLY
1aVDC UAX
SITITCH
18VDC)
TE I
Loading...